Subject: [PATCH 1/2] i2c: qup: add ACPI support

From: [email-masked] (Sricharan)
Date: Tue, 10 May 2016 11:35:55 +0530

+additional lists

> Add support to get the device parameters from ACPI. Assume that the clocks
> are managed by firmware.
> 
> Signed-off-by: Naveen Kaje <[email-masked]>
> ---
<snip>
> +	bool input_clk_ctrl = true;
> 
>  	qup = devm_kzalloc(&pdev->dev, sizeof(*qup), GFP_KERNEL);
>  	if (!qup)
> @@ -1372,7 +1378,14 @@ static int qup_i2c_probe(struct platform_device
> *pdev)
>  	init_completion(&qup->xfer);
>  	platform_set_drvdata(pdev, qup);
> 
> -	of_property_read_u32(node, "clock-frequency", &clk_freq);
> +	ret = device_property_read_u32(qup->dev, "clock-frequency",
> &clk_freq);
> +	if (ret) {
> +		dev_warn(qup->dev, "using default clock-frequency values");
> +		clk_freq = DEFAULT_CLK_FREQ;
> +	}
> +
> +	if (ACPI_HANDLE(qup->dev) && !node)
> +		input_clk_ctrl = false;
> 
>  	if (of_device_is_compatible(pdev->dev.of_node, "qcom,i2c-qup-
> v1.1.1")) {
>  		qup->adap.algo = &qup_i2c_algo;
> @@ -1454,20 +1467,29 @@ nodma:
>  		return qup->irq;
>  	}
> 
> -	qup->clk = devm_clk_get(qup->dev, "core");
> -	if (IS_ERR(qup->clk)) {
> -		dev_err(qup->dev, "Could not get core clock\n");
> -		return PTR_ERR(qup->clk);
> -	}
> +	if (input_clk_ctrl) {
     The above ACPI_HANDLE check can be directly used here and avoid the
variable.

> +		qup->clk = devm_clk_get(qup->dev, "core");
> +		if (IS_ERR(qup->clk)) {
> +			dev_err(qup->dev, "Could not get core clock\n");
> +			return PTR_ERR(qup->clk);
> +		}
> 
> -	qup->pclk = devm_clk_get(qup->dev, "iface");
> -	if (IS_ERR(qup->pclk)) {
> -		dev_err(qup->dev, "Could not get iface clock\n");
> -		return PTR_ERR(qup->pclk);
> +		qup->pclk = devm_clk_get(qup->dev, "iface");
> +		if (IS_ERR(qup->pclk)) {
> +			dev_err(qup->dev, "Could not get iface clock\n");
> +			return PTR_ERR(qup->pclk);
> +		}
> +		qup_i2c_enable_clocks(qup);
> +		src_clk_freq = clk_get_rate(qup->clk);
> +	} else {
> +		ret = device_property_read_u32(qup->dev,
> +				"src-clock-hz", &src_clk_freq);
> +		if (ret) {
> +			dev_warn(qup->dev, "using default src-clock-hz");
> +			src_clk_freq = DEFAULT_SRC_CLK;
> +		}
>  	}
> 
> -	qup_i2c_enable_clocks(qup);
> -
>  	/*
>  	 * Bootloaders might leave a pending interrupt on certain QUP's,
>  	 * so we reset the core before registering for interrupts.
> @@ -1514,7 +1536,6 @@ nodma:
>  	size = QUP_INPUT_FIFO_SIZE(io_mode);
>  	qup->in_fifo_sz = qup->in_blk_sz * (2 << size);
> 
> -	src_clk_freq = clk_get_rate(qup->clk);
>  	fs_div = ((src_clk_freq / clk_freq) / 2) - 3;
>  	hs_div = 3;
>  	qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); @@ -1534,6 +1555,8
> @@ nodma:
>  	qup->adap.dev.parent = qup->dev;
>  	qup->adap.dev.of_node = pdev->dev.of_node;
>  	qup->is_last = true;
> +	if (ACPI_HANDLE(qup->dev))
> +		ACPI_COMPANION_SET(&qup->adap.dev,
> ACPI_COMPANION(qup->dev));
    Can we move this inside the above check.
> 
>  	strlcpy(qup->adap.name, "QUP I2C adapter", sizeof(qup-
> >adap.name));
> 
> @@ -1639,6 +1662,13 @@ static const struct of_device_id
> qup_i2c_dt_match[] = {  };  MODULE_DEVICE_TABLE(of, qup_i2c_dt_match);
> 
> +#if IS_ENABLED(CONFIG_ACPI)
> +static const struct acpi_device_id qup_i2c_acpi_match[] = {
> +	{ "QCOM8010"},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(acpi, qup_i2c_acpi_ids); #endif
>  static struct platform_driver qup_i2c_driver = {
>  	.probe  = qup_i2c_probe,
>  	.remove = qup_i2c_remove,
> @@ -1646,6 +1676,7 @@ static struct platform_driver qup_i2c_driver = {
>  		.name = "i2c_qup",
>  		.pm = &qup_i2c_qup_pm_ops,
>  		.of_match_table = qup_i2c_dt_match,
> +		.acpi_match_table = ACPI_PTR(qup_i2c_acpi_match),
 Should this also be in #if IS_ENABLED(CONFIG_ACPI) check ?

Regards,
 Sricharan