Subject: Re: [PATCH v4 4/6] media: synopsys: Add PHY stopstate wait for i.MX93

From: Alexander Stein <[email-masked]>
Date: Wed, 20 May 2026 13:12:20 +0200

Hi,

Am Dienstag, 19. Mai 2026, 04:07:41 CEST schrieb Guoniu Zhou:
> Implement waiting for D-PHY lanes to enter stop state on i.MX93. This
> ensures proper PHY initialization by verifying that the clock lane and
> all active data lanes have entered the stop state before proceeding with
> further operations.
> 
> Reviewed-by: Frank Li <[email-masked]>
> Signed-off-by: Guoniu Zhou <[email-masked]>
> ---
> Changes in v2:
> - Removes redundant register availability check
> - Uses read_poll_timeout() with dw_mipi_csi2rx_read() instead of
>   readl_poll_timeout() with direct register address
> - Fixes stopstate condition logic
> - Check PHY stopstate after sensor enable instead of before to ensure
>   correct timing.
> - Optimize PHY stopstate polling parameters (1000us->10us, 2s->1ms) to
>   balance performance and responsiveness.
> ---
>  drivers/media/platform/synopsys/dw-mipi-csi2rx.c | 36 ++++++++++++++++++++++++
>  1 file changed, 36 insertions(+)
> 
> diff --git a/drivers/media/platform/synopsys/dw-mipi-csi2rx.c b/drivers/media/platform/synopsys/dw-mipi-csi2rx.c
> index 92178a3dec5d..8a34aec550ad 100644
> --- a/drivers/media/platform/synopsys/dw-mipi-csi2rx.c
> +++ b/drivers/media/platform/synopsys/dw-mipi-csi2rx.c
> @@ -11,6 +11,7 @@
>  #include <linux/clk.h>
>  #include <linux/delay.h>
>  #include <linux/io.h>
> +#include <linux/iopoll.h>
>  #include <linux/module.h>
>  #include <linux/of.h>
>  #include <linux/phy/phy.h>
> @@ -35,6 +36,8 @@
>  #define DW_REG_EXIST		BIT(31)
>  #define DW_REG(x)		(DW_REG_EXIST | (x))
>  
> +#define DPHY_STOPSTATE_CLK_LANE		BIT(16)
> +
>  #define DPHY_TEST_CTRL0_TEST_CLR	BIT(0)
>  
>  #define IPI_VCID_VC(x)			FIELD_PREP(GENMASK(1, 0), (x))
> @@ -65,6 +68,7 @@ enum dw_mipi_csi2rx_regs_index {
>  	DW_MIPI_CSI2RX_PHY_TST_CTRL0,
>  	DW_MIPI_CSI2RX_PHY_TST_CTRL1,
>  	DW_MIPI_CSI2RX_PHY_SHUTDOWNZ,
> +	DW_MIPI_CSI2RX_PHY_STOPSTATE,
>  	DW_MIPI_CSI2RX_IPI_DATATYPE,
>  	DW_MIPI_CSI2RX_IPI_MEM_FLUSH,
>  	DW_MIPI_CSI2RX_IPI_MODE,
> @@ -87,6 +91,7 @@ struct dw_mipi_csi2rx_drvdata {
>  	void (*dphy_assert_reset)(struct dw_mipi_csi2rx_device *csi2);
>  	void (*dphy_deassert_reset)(struct dw_mipi_csi2rx_device *csi2);
>  	void (*ipi_enable)(struct dw_mipi_csi2rx_device *csi2);
> +	int (*wait_for_phy_stopstate)(struct dw_mipi_csi2rx_device *csi2);
>  };
>  
>  struct dw_mipi_csi2rx_format {
> @@ -139,6 +144,7 @@ static const u32 imx93_regs[DW_MIPI_CSI2RX_MAX] = {
>  	[DW_MIPI_CSI2RX_PHY_SHUTDOWNZ] = DW_REG(0x40),
>  	[DW_MIPI_CSI2RX_DPHY_RSTZ] = DW_REG(0x44),
>  	[DW_MIPI_CSI2RX_PHY_STATE] = DW_REG(0x48),
> +	[DW_MIPI_CSI2RX_PHY_STOPSTATE] = DW_REG(0x4c),
>  	[DW_MIPI_CSI2RX_PHY_TST_CTRL0] = DW_REG(0x50),
>  	[DW_MIPI_CSI2RX_PHY_TST_CTRL1] = DW_REG(0x54),
>  	[DW_MIPI_CSI2RX_IPI_MODE] = DW_REG(0x80),
> @@ -556,10 +562,19 @@ static int dw_mipi_csi2rx_enable_streams(struct v4l2_subdev *sd,
>  	if (ret)
>  		goto err_csi_stop;
>  
> +	if (!csi2->enabled_streams &&
> +	    csi2->drvdata->wait_for_phy_stopstate) {
> +		ret = csi2->drvdata->wait_for_phy_stopstate(csi2);
> +		if (ret)
> +			goto err_disable_streams;
> +	}
> +
>  	csi2->enabled_streams |= streams_mask;
>  
>  	return 0;
>  
> +err_disable_streams:
> +	v4l2_subdev_disable_streams(remote_sd, remote_pad->index, mask);
>  err_csi_stop:
>  	/* Stop CSI hardware if no streams are enabled */
>  	if (!csi2->enabled_streams)
> @@ -871,11 +886,32 @@ static void imx93_csi2rx_dphy_ipi_enable(struct dw_mipi_csi2rx_device *csi2)
>  	dw_mipi_csi2rx_write(csi2, DW_MIPI_CSI2RX_IPI_MODE, val);
>  }
>  
> +static int imx93_csi2rx_wait_for_phy_stopstate(struct dw_mipi_csi2rx_device *csi2)
> +{
> +	struct device *dev = csi2->dev;
> +	u32 stopstate_mask;
> +	u32 val;
> +	int ret;
> +
> +	stopstate_mask = DPHY_STOPSTATE_CLK_LANE | GENMASK(csi2->lanes_num - 1, 0);
> +
> +	ret = read_poll_timeout(dw_mipi_csi2rx_read, val,
> +				(val & stopstate_mask) == stopstate_mask,
> +				 10, 1000, true,
> +				 csi2, DW_MIPI_CSI2RX_PHY_STOPSTATE);
> +	if (ret)
> +		dev_err(dev, "lanes are not in stop state: %#x, expected %#x\n",
> +			val, stopstate_mask);

Did you actually test this on imx93? I'm trying to get my imx327 sensor to
run, but only run into this error message:
dw-mipi-csi2rx 4ae00000.mipi-csi: lanes are not in stop state: 0x0, expected 0x10003

Currently I'm using this DT node:
--8<--
mipi_csi: mipi-csi@4ae00000 {
	compatible = "fsl,imx93-mipi-csi2";
	reg = <0x4ae00000 0x10000>;
	interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
	clocks = <&clk IMX93_CLK_MIPI_CSI_GATE>,
			<&clk IMX93_CLK_CAM_PIX>;
	clock-names = "per", "pixel";
	assigned-clocks = <&clk IMX93_CLK_CAM_PIX>;
	assigned-clock-parents = <&clk IMX93_CLK_VIDEO_PLL>;
	assigned-clock-rates = <140000000>;
	power-domains = <&media_blk_ctrl IMX93_MEDIABLK_PD_MIPI_CSI>;
	phys = <&dphy_rx>;
	phy-names = "dphy-rx";
	status = "disabled";

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
			reg = <0>;

			mipi_from_sensor: endpoint {
				data-lanes = <1 2>;
				bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
			};
		};

		port@1 {
			reg = <1>;

			mipi_to_isi: endpoint {
				remote-endpoint = <&isi_in>;
			};
		};
	};
};
--8<--

Am I'm missing something?

best regards,
Alexander

> +
> +	return ret;
> +}
> +
>  static const struct dw_mipi_csi2rx_drvdata imx93_drvdata = {
>  	.regs = imx93_regs,
>  	.dphy_assert_reset = imx93_csi2rx_dphy_assert_reset,
>  	.dphy_deassert_reset = imx93_csi2rx_dphy_deassert_reset,
>  	.ipi_enable = imx93_csi2rx_dphy_ipi_enable,
> +	.wait_for_phy_stopstate = imx93_csi2rx_wait_for_phy_stopstate,
>  };
>  
>  static const struct of_device_id dw_mipi_csi2rx_of_match[] = {
> 
> 

-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/