Subject: [PATCH v3] ARM: bcm: Add DEBUG_LL console support

From: [email-masked] (Christian Daudt)
Date: Sat, 5 Oct 2013 08:43:29 -0700

This patch adds low level debug uart support to Broadcom
 mobile based SOCs.

Signed-off-by: Christian Daudt <[email-masked]>

Changes from V2:
 - Changed to follow hex ordering on entries
 - Dropped defconfig changes

Changes from V1:
 - Switched to use the common 8250 debug introduced in 3.12-rc1

diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 9762c84..0391691 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -94,6 +94,17 @@ choice
 		depends on ARCH_BCM2835
 		select DEBUG_UART_PL01X
 
+	config DEBUG_BCM_KONA_UART
+		bool "Kernel low-level debugging messages via BCM KONA UART"
+		depends on ARCH_BCM
+		select DEBUG_UART_8250
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on Broadcom SoC platforms.
+		  This low level debug works for Broadcom
+		  mobile SoCs in the Kona family of chips (e.g. bcm28155,
+		  bcm11351, etc...)
+
 	config DEBUG_CLPS711X_UART1
 		bool "Kernel low-level debugging messages via UART1"
 		depends on ARCH_CLPS711X
@@ -951,6 +962,7 @@ config DEBUG_UART_PHYS
 	default 0x20064000 if DEBUG_RK29_UART1 || DEBUG_RK3X_UART2
 	default 0x20068000 if DEBUG_RK29_UART2 || DEBUG_RK3X_UART3
 	default 0x20201000 if DEBUG_BCM2835
+	default 0x3e000000 if DEBUG_BCM_KONA_UART
 	default 0x40090000 if ARCH_LPC32XX
 	default 0x40100000 if DEBUG_PXA_UART1
 	default 0x42000000 if ARCH_GEMINI
@@ -1010,6 +1022,7 @@ config DEBUG_UART_VIRT
 	default 0xfe018000 if DEBUG_MMP_UART3
 	default 0xfe100000 if DEBUG_IMX23_UART || DEBUG_IMX28_UART
 	default 0xfe230000 if DEBUG_PICOXCELL_UART
+	default 0xfe300000 if DEBUG_BCM_KONA_UART
 	default 0xfe800000 if ARCH_IOP32X
 	default 0xfeb00000 if DEBUG_HI3620_UART || DEBUG_HI3716_UART
 	default 0xfeb24000 if DEBUG_RK3X_UART0
@@ -1052,7 +1065,8 @@ config DEBUG_UART_8250_WORD
 	default y if DEBUG_PICOXCELL_UART || DEBUG_SOCFPGA_UART || \
 		ARCH_KEYSTONE || \
 		DEBUG_DAVINCI_DMx_UART0 || DEBUG_DAVINCI_DA8XX_UART1 || \
-		DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_DAVINCI_TNETV107X_UART1
+		DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_DAVINCI_TNETV107X_UART1 || \
+		DEBUG_BCM_KONA_UART
 
 config DEBUG_UART_8250_FLOW_CONTROL
 	bool "Enable flow control for 8250 UART"
-- 
1.7.10.4