From: pawel.moll@arm•com (Pawel Moll)
To: linux-arm-kernel@lists•infradead.org
Subject: [PATCH v2 RESEND 1/2] ARM: vexpress: Remove non-DT code
Date: Fri, 28 Nov 2014 15:53:04 +0000 [thread overview]
Message-ID: <1417189984.4371.12.camel@arm.com> (raw)
In-Reply-To: <20141128153026.GU3836@n2100.arm.linux.org.uk>
On Fri, 2014-11-28 at 15:30 +0000, Russell King - ARM Linux wrote:
> mmci-pl18x 10005000.mmci: no support for card's volts
> mmc0: error -22 whilst initialising SD card
Just tried it again:
--8<----------------------------
ARM Versatile Express Boot Monitor
Version: V5.2.1
Build Date: Apr 4 2013
Daughterboard Site 1: V2P-CA9 Cortex A9
Daughterboard Site 2: Not Used
Running boot script from flash - BOOTSCRIPT
Loaded FDT - ca9
Loaded initrd - busybox
Copied 0x400000 bytes from 0x48000000 to 0x60008000
Booting kernel @ 0x60008000
Command line 'console=ttyAMA0,38400 earlyprintk debug '
initrd @ 0x70000000 (4127012 bytes)
FDT @ 0x69000000 (14048 bytes)
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Linux version 3.18.0-rc6+ (pawmol01 at hornet) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1442 SMP Mon Nov 24 16:43:30 GMT 2014
CPU: ARMv7 Processor [410fc091] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: V2P-CA9
bootconsole [earlycon0] enabled
[...]
mmci-pl18x 10005000.mmci: Got CD GPIO
mmci-pl18x 10005000.mmci: Got WP GPIO
mmci-pl18x 10005000.mmci: Looking up vmmc-supply from device tree
mmci-pl18x 10005000.mmci: Looking up vqmmc-supply from device tree
mmci-pl18x 10005000.mmci: Looking up vqmmc-supply property in node /smb/motherboard/iofpga at 7,00000000/mmci at 05000 failed
mmci-pl18x 10005000.mmci: No vqmmc regulator found
mmci-pl18x 10005000.mmci: mmc0: PL180 manf 41 rev0 at 0x10005000 irq 41,42 (pio)
[...]
mmc0: new SD card@address 88f7
mmcblk0: mmc0:88f7 SD02G 1.84 GiB
mmcblk0: p1 p2
[...]
/ # mount /dev/mmcblk0p2 /mnt
EXT2-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
--8<------------------------------------
vmmc-supply is a defined as:
vmmc-supply = <&v2m_fixed_3v3>;
which is:
v2m_fixed_3v3: fixedregulator at 0 {
compatible = "regulator-fixed";
and arch/arm/mach-vexpress/Kconfig says:
menuconfig ARCH_VEXPRESS
[...]
select REGULATOR_FIXED_VOLTAGE if REGULATOR
but it doesn't select REGULATOR in result of this discussion:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/223426/focus=223427
To summarize, I believe that setting CONFIG_REGULATOR=y (as in
vexpress_defconfig) should solve your issue.
Pawel
next prev parent reply other threads:[~2014-11-28 15:53 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-11-25 18:17 [PATCH v2 RESEND 1/2] ARM: vexpress: Remove non-DT code Pawel Moll
2014-11-25 18:17 ` [PATCH 2/2] MAINTAINERS: ARM Versatile Express platform Pawel Moll
2014-11-26 1:54 ` Mike Turquette
2014-11-26 1:59 ` Joe Perches
2014-11-26 12:04 ` Pawel Moll
2014-11-26 12:17 ` Arnd Bergmann
2014-11-26 14:40 ` Pawel Moll
2014-11-26 15:40 ` Joe Perches
2014-11-26 12:13 ` [PATCH v2] " Pawel Moll
2014-11-28 15:14 ` Arnd Bergmann
2014-11-28 17:56 ` Joe Perches
2014-12-01 13:57 ` Pawel Moll
2014-12-01 14:16 ` [PATCH] MAINTAINERS: ARM Versatile Express platform, add missing pattern Pawel Moll
2014-12-04 16:02 ` Arnd Bergmann
2014-11-28 15:08 ` [PATCH v2 RESEND 1/2] ARM: vexpress: Remove non-DT code Arnd Bergmann
2014-11-28 15:30 ` Russell King - ARM Linux
2014-11-28 15:53 ` Pawel Moll [this message]
2014-11-28 16:31 ` Arnd Bergmann
2014-11-28 16:34 ` Pawel Moll
2014-11-28 16:44 ` [PATCH RESEND] ARM: vexpress: Enable regulator framework when MMCI is in use Pawel Moll
2014-11-28 20:57 ` Arnd Bergmann
2014-11-28 16:48 ` [PATCH v2 RESEND 1/2] ARM: vexpress: Remove non-DT code Russell King - ARM Linux
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1417189984.4371.12.camel@arm.com \
--to=pawel.moll@arm$(echo .)com \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox