Subject: [PATCH 1/3] ARM: dts: Add support for phyCORE-AM335x PCM-953 carrier board

From: [email-masked] (Teresa Remmet)
Date: Mon, 23 Jan 2017 11:27:12 +0100

Hello Rob,

Am Samstag, den 21.01.2017, 14:53 -0600 schrieb Rob Herring:
> On Thu, Jan 19, 2017 at 02:07:48PM +0100, Teresa Remmet wrote:
> > 
> > The phyCORE-AM335x development kit is a combination of the
> > phyCORE-AM335x SoM and a PCM-953 carrier board. The features
> > of the PCM-953 are:
> > * ETH phy on carrier board: 1x RGMII
> > * 1x CAN
> > * Up to 4x UART
> > * USB0 (otg)
> > * USB1 (host)
> > * SD slot
> > * User gpio-keys
> > * User LEDs
> > 
> > Signed-off-by: Teresa Remmet <[email-masked]>
> > Reviewed-by: Wadim Egorov <[email-masked]>
> > ---
> > ?.../devicetree/bindings/arm/omap/omap.txt??????????|???3 +
> > ?arch/arm/boot/dts/Makefile?????????????????????????|???1 +
> > ?arch/arm/boot/dts/am335x-pcm-953.dtsi??????????????| 303
> > +++++++++++++++++++++
> > ?arch/arm/boot/dts/am335x-phycore-rdk.dts???????????|??27 ++
> > ?4 files changed, 334 insertions(+)
> > ?create mode 100644 arch/arm/boot/dts/am335x-pcm-953.dtsi
> > ?create mode 100644 arch/arm/boot/dts/am335x-phycore-rdk.dts
> [...]
> 
> > 
> > +	user_leds: user_leds {
> > +		compatible = "gpio-leds";
> > +	};
> > +
> > +	user_buttons: user_buttons {
> > +		compatible = "gpio-keys";
> > +	};
> With only a compatible, I don't think there's much gain to split
> these 2?
> nodes. Otherwse,

whould it be ok to open up the root node again below? Or should I
better move the nodes up? Which does mess up the order then. We
orinented here on the am335x-pepper.dts. They also only keep the
compatibles in the root node.

Thanks,
Teresa

> 
> Acked-by: Rob Herring <[email-masked]>
> 
> > 
> > +&user_buttons {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&user_buttons_pins>;
> > +	status = "okay";
> > +
> > +	button at 0 {
> > +		label = "home";
> > +		linux,code = <KEY_HOME>;
> > +		gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> > +		gpio-key,wakeup;
> > +	};
> > +
> > +	button at 1 {
> > +		label = "menu";
> > +		linux,code = <KEY_MENU>;
> > +		gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
> > +		gpio-key,wakeup;
> > +	};
> > +};
> > +
> > +&user_leds {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&user_leds_pins>;
> > +	status = "okay";
> > +
> > +	green {
> > +		label = "green:user";
> > +		gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> > +		linux,default-trigger = "gpio";
> > +		default-state = "on";
> > +	};
> > +
> > +	yellow {
> > +		label = "yellow:user";
> > +		gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
> > +		linux,default-trigger = "gpio";
> > +		default-state = "on";
> > +	};
> > +};