Subject: [PATCH V6 2/2] thermal: imx: add i.MX7 thermal sensor support

From: [email-masked] (Zhang Rui)
Date: Tue, 13 Mar 2018 14:51:05 +0800

yeah, will review it and get back to you later.

On ?, 2018-03-13 at 06:13 +0000, Anson Huang wrote:
> Ping...
> 
> @rui.zhang at intel.com, can you help review this patch?
> 
> Anson Huang
> Best Regards!
> 
> 
> > 
> > -----Original Message-----
> > From: linux-arm-kernel [mailto:linux-arm-kernel-bounces at lists.infra
> > dead.org]
> > On Behalf Of Anson Huang
> > Sent: Friday, March 2, 2018 10:00 AM
> > To: Leonard Crestez <[email-masked]>; rui.zhang at intel.com;
> > edubezval at gmail.com; robh+dt at kernel.org; mark.rutland at arm.com;
> > shawnguo at kernel.org; kernel at pengutronix.de; Fabio Estevam
> > <[email-masked]>; linux at armlinux.org.uk
> > Cc: linux-arm-kernel at lists.infradead.org; devicetree at vger.kernel.or
> > g;
> > dl-linux-imx <[email-masked]>; linux-kernel at vger.kernel.org;
> > linux-pm at vger.kernel.org
> > Subject: [PATCH V6 2/2] thermal: imx: add i.MX7 thermal sensor
> > support
> > 
> > This patch adds i.MX7 thermal sensor support, most of the i.MX7
> > thermal sensor
> > functions are same with
> > i.MX6 except the registers offset/layout, so we move those
> > registers
> > offset/layout definitions to soc data structure.
> > 
> > i.MX7 uses single calibration data @25C, the calibration data is
> > located at
> > OCOTP offset 0x4F0, bit[17:9], the formula is as below:
> > 
> > Tmeas = (Nmeas - n1) + 25; n1 is the fuse value for 25C.
> > 
> > Signed-off-by: Anson Huang <[email-masked]>
> > Signed-off-by: Bai Ping <[email-masked]>
> > Acked-by: Dong Aisheng <[email-masked]>
> > Acked-by: Shawn Guo <[email-masked]>
> > Reviewed-by: Rob Herring <[email-masked]>
> > ---
> > changes since V5:
> > 	no code change, just add Reviewed-by.
> > ?.../devicetree/bindings/thermal/imx-thermal.txt????|???9 +-
> > ?drivers/thermal/imx_thermal.c??????????????????????| 295
> > ++++++++++++++++-----
> > ?2 files changed, 239 insertions(+), 65 deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/thermal/imx-
> > thermal.txt
> > b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > index 28be51a..38bffcc 100644
> > --- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > +++ b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > @@ -1,8 +1,13 @@
> > ?* Temperature Monitor (TEMPMON) on Freescale i.MX SoCs
> > 
> > ?Required properties:
> > -- compatible : "fsl,imx6q-tempmon" for i.MX6Q, "fsl,imx6sx-
> > tempmon" for
> > i.MX6SX.
> > -??i.MX6SX has two more IRQs than i.MX6Q, one is IRQ_LOW and the
> > other is
> > IRQ_PANIC,
> > +- compatible : must be one of following:
> > +??- "fsl,imx6q-tempmon" for i.MX6Q,
> > +??- "fsl,imx6sx-tempmon" for i.MX6SX,
> > +??- "fsl,imx7d-tempmon" for i.MX7S/D.
> > +- interrupts : the interrupt output of the controller:
> > +??i.MX6Q has one IRQ which will be triggered when temperature is
> > higher
> > +than high threshold,
> > +??i.MX6SX and i.MX7S/D have two more IRQs than i.MX6Q, one is
> > IRQ_LOW
> > +and the other is IRQ_PANIC,
> > ???when temperature is below than low threshold, IRQ_LOW will be
> > triggered,
> > when temperature
> > ???is higher than panic threshold, system will auto reboot by SRC
> > module.
> > ?- fsl,tempmon : phandle pointer to system controller that contains
> > TEMPMON
> > diff --git a/drivers/thermal/imx_thermal.c
> > b/drivers/thermal/imx_thermal.c
> > index a67781b..569d41b 100644
> > --- a/drivers/thermal/imx_thermal.c
> > +++ b/drivers/thermal/imx_thermal.c
> > @@ -31,35 +31,57 @@
> > ?#define REG_CLR		0x8
> > ?#define REG_TOG		0xc
> > 
> > -#define MISC0				0x0150
> > -#define MISC0_REFTOP_SELBIASOFF		(1 << 3)
> > -#define MISC1				0x0160
> > -#define MISC1_IRQ_TEMPHIGH		(1 << 29)
> > +/* i.MX6 specific */
> > +#define IMX6_MISC0				0x0150
> > +#define IMX6_MISC0_REFTOP_SELBIASOFF		(1 << 3)
> > +#define IMX6_MISC1				0x0160
> > +#define IMX6_MISC1_IRQ_TEMPHIGH			(1 << 29)
> > ?/* Below LOW and PANIC bits are only for TEMPMON_IMX6SX */
> > -#define MISC1_IRQ_TEMPLOW		(1 << 28)
> > -#define MISC1_IRQ_TEMPPANIC		(1 << 27)
> > -
> > -#define TEMPSENSE0			0x0180
> > -#define TEMPSENSE0_ALARM_VALUE_SHIFT	20
> > -#define TEMPSENSE0_ALARM_VALUE_MASK	(0xfff <<
> > TEMPSENSE0_ALARM_VALUE_SHIFT)
> > -#define TEMPSENSE0_TEMP_CNT_SHIFT	8
> > -#define TEMPSENSE0_TEMP_CNT_MASK	(0xfff <<
> > TEMPSENSE0_TEMP_CNT_SHIFT)
> > -#define TEMPSENSE0_FINISHED		(1 << 2)
> > -#define TEMPSENSE0_MEASURE_TEMP		(1 << 1)
> > -#define TEMPSENSE0_POWER_DOWN		(1 << 0)
> > -
> > -#define TEMPSENSE1			0x0190
> > -#define TEMPSENSE1_MEASURE_FREQ		0xffff
> > -/* Below TEMPSENSE2 is only for TEMPMON_IMX6SX */
> > -#define TEMPSENSE2			0x0290
> > -#define TEMPSENSE2_LOW_VALUE_SHIFT	0
> > -#define TEMPSENSE2_LOW_VALUE_MASK	0xfff
> > -#define TEMPSENSE2_PANIC_VALUE_SHIFT	16
> > -#define TEMPSENSE2_PANIC_VALUE_MASK	0xfff0000
> > +#define IMX6_MISC1_IRQ_TEMPLOW			(1 << 28)
> > +#define IMX6_MISC1_IRQ_TEMPPANIC		(1 << 27)
> > +
> > +#define IMX6_TEMPSENSE0				0x0180
> > +#define IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT	20
> > +#define IMX6_TEMPSENSE0_ALARM_VALUE_MASK	(0xfff << 20)
> > +#define IMX6_TEMPSENSE0_TEMP_CNT_SHIFT		8
> > +#define IMX6_TEMPSENSE0_TEMP_CNT_MASK		(0xfff << 8)
> > +#define IMX6_TEMPSENSE0_FINISHED		(1 << 2)
> > +#define IMX6_TEMPSENSE0_MEASURE_TEMP		(1 << 1)
> > +#define IMX6_TEMPSENSE0_POWER_DOWN		(1 << 0)
> > +
> > +#define IMX6_TEMPSENSE1				0x0190
> > +#define IMX6_TEMPSENSE1_MEASURE_FREQ		0xffff
> > +#define IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT	0
> > 
> > ?#define OCOTP_MEM0			0x0480
> > ?#define OCOTP_ANA1			0x04e0
> > 
> > +/* Below TEMPSENSE2 is only for TEMPMON_IMX6SX */
> > +#define IMX6_TEMPSENSE2				0x0290
> > +#define IMX6_TEMPSENSE2_LOW_VALUE_SHIFT		0
> > +#define IMX6_TEMPSENSE2_LOW_VALUE_MASK		0xfff
> > +#define IMX6_TEMPSENSE2_PANIC_VALUE_SHIFT	16
> > +#define IMX6_TEMPSENSE2_PANIC_VALUE_MASK	0xfff0000
> > +
> > +/* i.MX7 specific */
> > +#define IMX7_ANADIG_DIGPROG			0x800
> > +#define IMX7_TEMPSENSE0				0x300
> > +#define IMX7_TEMPSENSE0_PANIC_ALARM_SHIFT	18
> > +#define IMX7_TEMPSENSE0_PANIC_ALARM_MASK	(0x1ff << 18)
> > +#define IMX7_TEMPSENSE0_HIGH_ALARM_SHIFT	9
> > +#define IMX7_TEMPSENSE0_HIGH_ALARM_MASK		(0x1ff <<
> > 9)
> > +#define IMX7_TEMPSENSE0_LOW_ALARM_SHIFT		0
> > +#define IMX7_TEMPSENSE0_LOW_ALARM_MASK		0x1ff
> > +
> > +#define IMX7_TEMPSENSE1				0x310
> > +#define IMX7_TEMPSENSE1_MEASURE_FREQ_SHIFT	16
> > +#define IMX7_TEMPSENSE1_MEASURE_FREQ_MASK	(0xffff << 16)
> > +#define IMX7_TEMPSENSE1_FINISHED		(1 << 11)
> > +#define IMX7_TEMPSENSE1_MEASURE_TEMP		(1 << 10)
> > +#define IMX7_TEMPSENSE1_POWER_DOWN		(1 << 9)
> > +#define IMX7_TEMPSENSE1_TEMP_VALUE_SHIFT	0
> > +#define IMX7_TEMPSENSE1_TEMP_VALUE_MASK		0x1ff
> > +
> > ?/* The driver supports 1 passive trip point and 1 critical trip
> > point */??enum
> > imx_thermal_trip {
> > ?	IMX_TRIP_PASSIVE,
> > @@ -72,17 +94,114 @@ enum imx_thermal_trip {
> > 
> > ?#define TEMPMON_IMX6Q			1
> > ?#define TEMPMON_IMX6SX			2
> > +#define TEMPMON_IMX7D			3
> > 
> > ?struct thermal_soc_data {
> > ?	u32 version;
> > +
> > +	u32 sensor_ctrl;
> > +	u32 power_down_mask;
> > +	u32 measure_temp_mask;
> > +
> > +	u32 measure_freq_ctrl;
> > +	u32 measure_freq_mask;
> > +	u32 measure_freq_shift;
> > +
> > +	u32 temp_data;
> > +	u32 temp_value_mask;
> > +	u32 temp_value_shift;
> > +	u32 temp_valid_mask;
> > +
> > +	u32 panic_alarm_ctrl;
> > +	u32 panic_alarm_mask;
> > +	u32 panic_alarm_shift;
> > +
> > +	u32 high_alarm_ctrl;
> > +	u32 high_alarm_mask;
> > +	u32 high_alarm_shift;
> > +
> > +	u32 low_alarm_ctrl;
> > +	u32 low_alarm_mask;
> > +	u32 low_alarm_shift;
> > ?};
> > 
> > ?static struct thermal_soc_data thermal_imx6q_data = {
> > ?	.version = TEMPMON_IMX6Q,
> > +
> > +	.sensor_ctrl = IMX6_TEMPSENSE0,
> > +	.power_down_mask = IMX6_TEMPSENSE0_POWER_DOWN,
> > +	.measure_temp_mask = IMX6_TEMPSENSE0_MEASURE_TEMP,
> > +
> > +	.measure_freq_ctrl = IMX6_TEMPSENSE1,
> > +	.measure_freq_shift = IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT,
> > +	.measure_freq_mask = IMX6_TEMPSENSE1_MEASURE_FREQ,
> > +
> > +	.temp_data = IMX6_TEMPSENSE0,
> > +	.temp_value_mask = IMX6_TEMPSENSE0_TEMP_CNT_MASK,
> > +	.temp_value_shift = IMX6_TEMPSENSE0_TEMP_CNT_SHIFT,
> > +	.temp_valid_mask = IMX6_TEMPSENSE0_FINISHED,
> > +
> > +	.high_alarm_ctrl = IMX6_TEMPSENSE0,
> > +	.high_alarm_mask = IMX6_TEMPSENSE0_ALARM_VALUE_MASK,
> > +	.high_alarm_shift = IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT,
> > ?};
> > 
> > ?static struct thermal_soc_data thermal_imx6sx_data = {
> > ?	.version = TEMPMON_IMX6SX,
> > +
> > +	.sensor_ctrl = IMX6_TEMPSENSE0,
> > +	.power_down_mask = IMX6_TEMPSENSE0_POWER_DOWN,
> > +	.measure_temp_mask = IMX6_TEMPSENSE0_MEASURE_TEMP,
> > +
> > +	.measure_freq_ctrl = IMX6_TEMPSENSE1,
> > +	.measure_freq_shift = IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT,
> > +	.measure_freq_mask = IMX6_TEMPSENSE1_MEASURE_FREQ,
> > +
> > +	.temp_data = IMX6_TEMPSENSE0,
> > +	.temp_value_mask = IMX6_TEMPSENSE0_TEMP_CNT_MASK,
> > +	.temp_value_shift = IMX6_TEMPSENSE0_TEMP_CNT_SHIFT,
> > +	.temp_valid_mask = IMX6_TEMPSENSE0_FINISHED,
> > +
> > +	.high_alarm_ctrl = IMX6_TEMPSENSE0,
> > +	.high_alarm_mask = IMX6_TEMPSENSE0_ALARM_VALUE_MASK,
> > +	.high_alarm_shift = IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT,
> > +
> > +	.panic_alarm_ctrl = IMX6_TEMPSENSE2,
> > +	.panic_alarm_mask = IMX6_TEMPSENSE2_PANIC_VALUE_MASK,
> > +	.panic_alarm_shift = IMX6_TEMPSENSE2_PANIC_VALUE_SHIFT,
> > +
> > +	.low_alarm_ctrl = IMX6_TEMPSENSE2,
> > +	.low_alarm_mask = IMX6_TEMPSENSE2_LOW_VALUE_MASK,
> > +	.low_alarm_shift = IMX6_TEMPSENSE2_LOW_VALUE_SHIFT, };
> > +
> > +static struct thermal_soc_data thermal_imx7d_data = {
> > +	.version = TEMPMON_IMX7D,
> > +
> > +	.sensor_ctrl = IMX7_TEMPSENSE1,
> > +	.power_down_mask = IMX7_TEMPSENSE1_POWER_DOWN,
> > +	.measure_temp_mask = IMX7_TEMPSENSE1_MEASURE_TEMP,
> > +
> > +	.measure_freq_ctrl = IMX7_TEMPSENSE1,
> > +	.measure_freq_shift = IMX7_TEMPSENSE1_MEASURE_FREQ_SHIFT,
> > +	.measure_freq_mask = IMX7_TEMPSENSE1_MEASURE_FREQ_MASK,
> > +
> > +	.temp_data = IMX7_TEMPSENSE1,
> > +	.temp_value_mask = IMX7_TEMPSENSE1_TEMP_VALUE_MASK,
> > +	.temp_value_shift = IMX7_TEMPSENSE1_TEMP_VALUE_SHIFT,
> > +	.temp_valid_mask = IMX7_TEMPSENSE1_FINISHED,
> > +
> > +	.panic_alarm_ctrl = IMX7_TEMPSENSE1,
> > +	.panic_alarm_mask = IMX7_TEMPSENSE0_PANIC_ALARM_MASK,
> > +	.panic_alarm_shift = IMX7_TEMPSENSE0_PANIC_ALARM_SHIFT,
> > +
> > +	.high_alarm_ctrl = IMX7_TEMPSENSE0,
> > +	.high_alarm_mask = IMX7_TEMPSENSE0_HIGH_ALARM_MASK,
> > +	.high_alarm_shift = IMX7_TEMPSENSE0_HIGH_ALARM_SHIFT,
> > +
> > +	.low_alarm_ctrl = IMX7_TEMPSENSE0,
> > +	.low_alarm_mask = IMX7_TEMPSENSE0_LOW_ALARM_MASK,
> > +	.low_alarm_shift = IMX7_TEMPSENSE0_LOW_ALARM_SHIFT,
> > ?};
> > 
> > ?struct imx_thermal_data {
> > @@ -107,31 +226,42 @@ struct imx_thermal_data {??static void
> > imx_set_panic_temp(struct imx_thermal_data *data,
> > ?			???????int panic_temp)
> > ?{
> > +	const struct thermal_soc_data *soc_data = data->socdata;
> > ?	struct regmap *map = data->tempmon;
> > ?	int critical_value;
> > 
> > ?	critical_value = (data->c2 - panic_temp) / data->c1;
> > -	regmap_write(map, TEMPSENSE2 + REG_CLR,
> > TEMPSENSE2_PANIC_VALUE_MASK);
> > -	regmap_write(map, TEMPSENSE2 + REG_SET, critical_value <<
> > -			TEMPSENSE2_PANIC_VALUE_SHIFT);
> > +
> > +	regmap_write(map, soc_data->panic_alarm_ctrl + REG_CLR,
> > +		?????soc_data->panic_alarm_mask);
> > +	regmap_write(map, soc_data->panic_alarm_ctrl + REG_SET,
> > +		?????critical_value << soc_data-
> > >panic_alarm_shift);
> > ?}
> > 
> > ?static void imx_set_alarm_temp(struct imx_thermal_data *data,
> > ?			???????int alarm_temp)
> > ?{
> > ?	struct regmap *map = data->tempmon;
> > +	const struct thermal_soc_data *soc_data = data->socdata;
> > ?	int alarm_value;
> > 
> > ?	data->alarm_temp = alarm_temp;
> > -	alarm_value = (data->c2 - alarm_temp) / data->c1;
> > -	regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_ALARM_VALUE_MASK);
> > -	regmap_write(map, TEMPSENSE0 + REG_SET, alarm_value <<
> > -			TEMPSENSE0_ALARM_VALUE_SHIFT);
> > +
> > +	if (data->socdata->version == TEMPMON_IMX7D)
> > +		alarm_value = alarm_temp / 1000 + data->c1 - 25;
> > +	else
> > +		alarm_value = (data->c2 - alarm_temp) / data->c1;
> > +
> > +	regmap_write(map, soc_data->high_alarm_ctrl + REG_CLR,
> > +		?????soc_data->high_alarm_mask);
> > +	regmap_write(map, soc_data->high_alarm_ctrl + REG_SET,
> > +		?????alarm_value << soc_data->high_alarm_shift);
> > ?}
> > 
> > ?static int imx_get_temp(struct thermal_zone_device *tz, int
> > *temp)??{
> > ?	struct imx_thermal_data *data = tz->devdata;
> > +	const struct thermal_soc_data *soc_data = data->socdata;
> > ?	struct regmap *map = data->tempmon;
> > ?	unsigned int n_meas;
> > ?	bool wait;
> > @@ -139,16 +269,18 @@ static int imx_get_temp(struct
> > thermal_zone_device
> > *tz, int *temp)
> > 
> > ?	if (data->mode == THERMAL_DEVICE_ENABLED) {
> > ?		/* Check if a measurement is currently in progress
> > */
> > -		regmap_read(map, TEMPSENSE0, &val);
> > -		wait = !(val & TEMPSENSE0_FINISHED);
> > +		regmap_read(map, soc_data->temp_data, &val);
> > +		wait = !(val & soc_data->temp_valid_mask);
> > ?	} else {
> > ?		/*
> > ?		?* Every time we measure the temperature, we will
> > power on the
> > ?		?* temperature sensor, enable measurements, take a
> > reading,
> > ?		?* disable measurements, power off the temperature
> > sensor.
> > ?		?*/
> > -		regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > -		regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > +		regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > +			????soc_data->power_down_mask);
> > +		regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > +			????soc_data->measure_temp_mask);
> > 
> > ?		wait = true;
> > ?	}
> > @@ -160,22 +292,28 @@ static int imx_get_temp(struct
> > thermal_zone_device
> > *tz, int *temp)
> > ?	if (wait)
> > ?		usleep_range(20, 50);
> > 
> > -	regmap_read(map, TEMPSENSE0, &val);
> > +	regmap_read(map, soc_data->temp_data, &val);
> > 
> > ?	if (data->mode != THERMAL_DEVICE_ENABLED) {
> > -		regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > -		regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > +		regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > +			?????soc_data->measure_temp_mask);
> > +		regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > +			?????soc_data->power_down_mask);
> > ?	}
> > 
> > -	if ((val & TEMPSENSE0_FINISHED) == 0) {
> > +	if ((val & soc_data->temp_valid_mask) == 0) {
> > ?		dev_dbg(&tz->device, "temp measurement never
> > finished\n");
> > ?		return -EAGAIN;
> > ?	}
> > 
> > -	n_meas = (val & TEMPSENSE0_TEMP_CNT_MASK) >>
> > TEMPSENSE0_TEMP_CNT_SHIFT;
> > +	n_meas = (val & soc_data->temp_value_mask)
> > +		>> soc_data->temp_value_shift;
> > 
> > ?	/* See imx_init_calib() for formula derivation */
> > -	*temp = data->c2 - n_meas * data->c1;
> > +	if (data->socdata->version == TEMPMON_IMX7D)
> > +		*temp = (n_meas - data->c1 + 25) * 1000;
> > +	else
> > +		*temp = data->c2 - n_meas * data->c1;
> > 
> > ?	/* Update alarm value to next higher trip point for
> > TEMPMON_IMX6Q */
> > ?	if (data->socdata->version == TEMPMON_IMX6Q) { @@ -219,21
> > +357,26
> > @@ static int imx_set_mode(struct thermal_zone_device *tz,??{
> > ?	struct imx_thermal_data *data = tz->devdata;
> > ?	struct regmap *map = data->tempmon;
> > +	const struct thermal_soc_data *soc_data = data->socdata;
> > 
> > ?	if (mode == THERMAL_DEVICE_ENABLED) {
> > ?		tz->polling_delay = IMX_POLLING_DELAY;
> > ?		tz->passive_delay = IMX_PASSIVE_DELAY;
> > 
> > -		regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > -		regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > +		regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > +			?????soc_data->power_down_mask);
> > +		regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > +			?????soc_data->measure_temp_mask);
> > 
> > ?		if (!data->irq_enabled) {
> > ?			data->irq_enabled = true;
> > ?			enable_irq(data->irq);
> > ?		}
> > ?	} else {
> > -		regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > -		regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > +		regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > +			?????soc_data->measure_temp_mask);
> > +		regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > +			?????soc_data->power_down_mask);
> > 
> > ?		tz->polling_delay = 0;
> > ?		tz->passive_delay = 0;
> > @@ -355,6 +498,15 @@ static int imx_init_calib(struct
> > platform_device *pdev,
> > u32 ocotp_ana1)
> > ?	}
> > 
> > ?	/*
> > +	?* On i.MX7D, we only use the calibration data at 25C to
> > get the temp,
> > +	?* Tmeas = ( Nmeas - n1) + 25; n1 is the fuse value for
> > 25C.
> > +	?*/
> > +	if (data->socdata->version == TEMPMON_IMX7D) {
> > +		data->c1 = (ocotp_ana1 >> 9) & 0x1ff;
> > +		return 0;
> > +	}
> > +
> > +	/*
> > ?	?* The sensor is calibrated at 25 ?C (aka T1) and the
> > value measured
> > ?	?* (aka N1) at this temperature is provided in bits
> > [31:20] in the
> > ?	?* i.MX's OCOTP value ANA1.
> > @@ -492,6 +644,7 @@ static irqreturn_t
> > imx_thermal_alarm_irq_thread(int
> > irq, void *dev)??static const struct of_device_id
> > of_imx_thermal_match[] = {
> > ?	{ .compatible = "fsl,imx6q-tempmon", .data =
> > &thermal_imx6q_data, },
> > ?	{ .compatible = "fsl,imx6sx-tempmon", .data =
> > &thermal_imx6sx_data, },
> > +	{ .compatible = "fsl,imx7d-tempmon", .data =
> > &thermal_imx7d_data, },
> > ?	{ /* end */ }
> > ?};
> > ?MODULE_DEVICE_TABLE(of, of_imx_thermal_match); @@ -523,14 +676,15
> > @@ static int imx_thermal_probe(struct platform_device *pdev)
> > 
> > ?	/* make sure the IRQ flag is clear before enabling irq on
> > i.MX6SX */
> > ?	if (data->socdata->version == TEMPMON_IMX6SX) {
> > -		regmap_write(map, MISC1 + REG_CLR,
> > MISC1_IRQ_TEMPHIGH |
> > -			MISC1_IRQ_TEMPLOW | MISC1_IRQ_TEMPPANIC);
> > +		regmap_write(map, IMX6_MISC1 + REG_CLR,
> > +			IMX6_MISC1_IRQ_TEMPHIGH |
> > IMX6_MISC1_IRQ_TEMPLOW
> > +			| IMX6_MISC1_IRQ_TEMPPANIC);
> > ?		/*
> > ?		?* reset value of LOW ALARM is incorrect, set it
> > to lowest
> > ?		?* value to avoid false trigger of low alarm.
> > ?		?*/
> > -		regmap_write(map, TEMPSENSE2 + REG_SET,
> > -			TEMPSENSE2_LOW_VALUE_MASK);
> > +		regmap_write(map, data->socdata->low_alarm_ctrl +
> > REG_SET,
> > +			?????data->socdata->low_alarm_mask);
> > ?	}
> > 
> > ?	data->irq = platform_get_irq(pdev, 0); @@ -557,11 +711,17
> > @@ static int
> > imx_thermal_probe(struct platform_device *pdev)
> > ?	}
> > 
> > ?	/* Make sure sensor is in known good state for
> > measurements */
> > -	regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > -	regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > -	regmap_write(map, TEMPSENSE1 + REG_CLR,
> > TEMPSENSE1_MEASURE_FREQ);
> > -	regmap_write(map, MISC0 + REG_SET,
> > MISC0_REFTOP_SELBIASOFF);
> > -	regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > +	regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > +		?????data->socdata->power_down_mask);
> > +	regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > +		?????data->socdata->measure_temp_mask);
> > +	regmap_write(map, data->socdata->measure_freq_ctrl +
> > REG_CLR,
> > +		?????data->socdata->measure_freq_mask);
> > +	if (data->socdata->version != TEMPMON_IMX7D)
> > +		regmap_write(map, IMX6_MISC0 + REG_SET,
> > +			IMX6_MISC0_REFTOP_SELBIASOFF);
> > +	regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > +		?????data->socdata->power_down_mask);
> > 
> > ?	data->policy = cpufreq_cpu_get(0);
> > ?	if (!data->policy) {
> > @@ -626,16 +786,20 @@ static int imx_thermal_probe(struct
> > platform_device
> > *pdev)
> > ?		?data->temp_passive / 1000);
> > 
> > ?	/* Enable measurements at ~ 10 Hz */
> > -	regmap_write(map, TEMPSENSE1 + REG_CLR,
> > TEMPSENSE1_MEASURE_FREQ);
> > +	regmap_write(map, data->socdata->measure_freq_ctrl +
> > REG_CLR,
> > +		?????data->socdata->measure_freq_mask);
> > ?	measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
> > -	regmap_write(map, TEMPSENSE1 + REG_SET, measure_freq);
> > +	regmap_write(map, data->socdata->measure_freq_ctrl +
> > REG_SET,
> > +		?????measure_freq << data->socdata-
> > >measure_freq_shift);
> > ?	imx_set_alarm_temp(data, data->temp_passive);
> > 
> > ?	if (data->socdata->version == TEMPMON_IMX6SX)
> > ?		imx_set_panic_temp(data, data->temp_critical);
> > 
> > -	regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > -	regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > +	regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > +		?????data->socdata->power_down_mask);
> > +	regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > +		?????data->socdata->measure_temp_mask);
> > 
> > ?	ret = devm_request_threaded_irq(&pdev->dev, data->irq,
> > ?			imx_thermal_alarm_irq,
> > imx_thermal_alarm_irq_thread, @@
> > -661,7 +825,8 @@ static int imx_thermal_remove(struct
> > platform_device
> > *pdev)
> > ?	struct regmap *map = data->tempmon;
> > 
> > ?	/* Disable measurements */
> > -	regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > +	regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > +		?????data->socdata->power_down_mask);
> > ?	if (!IS_ERR(data->thermal_clk))
> > ?		clk_disable_unprepare(data->thermal_clk);
> > 
> > @@ -684,8 +849,10 @@ static int imx_thermal_suspend(struct device
> > *dev)
> > ?	?* temperature will be read as the thermal sensor is
> > powered
> > ?	?* down.
> > ?	?*/
> > -	regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > -	regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > +	regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > +		?????data->socdata->measure_temp_mask);
> > +	regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > +		?????data->socdata->power_down_mask);
> > ?	data->mode = THERMAL_DEVICE_DISABLED;
> > ?	clk_disable_unprepare(data->thermal_clk);
> > 
> > @@ -702,8 +869,10 @@ static int imx_thermal_resume(struct device
> > *dev)
> > ?	if (ret)
> > ?		return ret;
> > ?	/* Enabled thermal sensor after resume */
> > -	regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > -	regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > +	regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > +		?????data->socdata->power_down_mask);
> > +	regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > +		?????data->socdata->measure_temp_mask);
> > ?	data->mode = THERMAL_DEVICE_ENABLED;
> > 
> > ?	return 0;
> > --
> > 2.7.4
> > 
> > 
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > https://emea01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fl
> > ists.infr
> > adead.org%2Fmailman%2Flistinfo%2Flinux-arm-
> > kernel&data=02%7C01%7Cans
> > on.huang%40nxp.com%7C06aac542a9cb445ee0f308d57fe1cbba%7C686ea1d3
> > bc2b4c6fa92cd99c5c301635%7C0%7C0%7C636555530125162768&sdata=GP4
> > UyKpDXyRkmwSIZY9Sb%2BDxO9sPAWCk0O%2FZPYRA0P4%3D&reserved=0