Subject: [PATCH 2/2] ARM: imx6q: add cpu suspend/resume support in IRAM

From: [email-masked] (Jason Chen)
Date: Wed, 4 Jan 2012 15:24:07 +0800

hi, Shawn,

I'll separate this patches and update with your comments.

On Tue, Jan 03, 2012 at 10:24:51PM +0800, Shawn Guo wrote:
> On Sat, Dec 31, 2011 at 02:23:44PM +0800, Jason Chen wrote:
> > For most power saving, this patch make arm core stop and
> 
> s/most/more?
> 
> Without this patch, the 'mem' state already powers arm core off.
> 
> > ddr go into self-refresh mode.
> > 
> > It already be tested on Freescale imx6q-arm2 board.
> > 
> 
> I managed to apply the patch on v3.2-rc7 and tested it on ARM2 board,
> but it does not work for me.
> 
> > Signed-off-by: Jason Chen <[email-masked]>
> > Signed-off-by: Jason Chen <[email-masked]>
> > ---
> >  arch/arm/mach-imx/Makefile              |    2 +-
> >  arch/arm/mach-imx/clock-imx6q.c         |   37 +++--
> >  arch/arm/mach-imx/gpc.c                 |   21 ++
> >  arch/arm/mach-imx/pm-imx6q.c            |  128 +++++++++++++-
> >  arch/arm/mach-imx/suspend-imx6q.S       |  308 +++++++++++++++++++++++++++++++
> >  arch/arm/plat-mxc/include/mach/common.h |    2 +
> >  arch/arm/plat-mxc/include/mach/mx6q.h   |    6 +
> >  7 files changed, 487 insertions(+), 17 deletions(-)
> > 
> 
> The checkpatch.pl reports 3 warnings.
> 
> > diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
> > index 88a3966..0b07eef 100644
> > --- a/arch/arm/mach-imx/Makefile
> > +++ b/arch/arm/mach-imx/Makefile
> > @@ -72,7 +72,7 @@ AFLAGS_head-v7.o :=-Wa,-march=armv7-a
> >  obj-$(CONFIG_SMP) += platsmp.o
> >  obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
> >  obj-$(CONFIG_LOCAL_TIMERS) += localtimer.o
> > -obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o mach-imx6q.o pm-imx6q.o
> > +obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o mach-imx6q.o pm-imx6q.o suspend-imx6q.o
> >  
> >  # i.MX5 based machines
> >  obj-$(CONFIG_MACH_MX51_BABBAGE) += mach-mx51_babbage.o
> > diff --git a/arch/arm/mach-imx/clock-imx6q.c b/arch/arm/mach-imx/clock-imx6q.c
> > index 56a7a3f..b7fecad 100644
> > --- a/arch/arm/mach-imx/clock-imx6q.c
> > +++ b/arch/arm/mach-imx/clock-imx6q.c
> > @@ -115,6 +115,8 @@
> >  #define CG14		28
> >  #define CG15		30
> >  
> > +#define BM_CCR_RBC_EN			(0x1 << 27)
> > +
> >  #define BM_CCSR_PLL1_SW_SEL		(0x1 << 2)
> >  #define BM_CCSR_STEP_SEL		(0x1 << 8)
> >  
> > @@ -1916,33 +1918,44 @@ static struct clk_lookup lookups[] = {
> >  
> >  int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode)
> >  {
> > -	u32 val = readl_relaxed(CLPCR);
> > +	u32 clpcr = readl_relaxed(CLPCR);
> > +	u32 ccr = readl_relaxed(CCR);
> >  
> > -	val &= ~BM_CLPCR_LPM;
> > +	clpcr &= ~(BM_CLPCR_LPM | BM_CLPCR_VSTBY | BM_CLPCR_SBYOS
> > +			| BM_CLPCR_STBY_COUNT | BM_CLPCR_WB_PER_AT_LPM);
> > +	ccr &= ~(BM_CCR_RBC_EN);
> >  	switch (mode) {
> >  	case WAIT_CLOCKED:
> >  		break;
> >  	case WAIT_UNCLOCKED:
> > -		val |= 0x1 << BP_CLPCR_LPM;
> > +		clpcr |= 0x1 << BP_CLPCR_LPM;
> >  		break;
> >  	case STOP_POWER_ON:
> > -		val |= 0x2 << BP_CLPCR_LPM;
> > +		clpcr |= 0x2 << BP_CLPCR_LPM;
> >  		break;
> >  	case WAIT_UNCLOCKED_POWER_OFF:
> > -		val |= 0x1 << BP_CLPCR_LPM;
> > -		val &= ~BM_CLPCR_VSTBY;
> > -		val &= ~BM_CLPCR_SBYOS;
> > +		clpcr |= 0x1 << BP_CLPCR_LPM;
> >  		break;
> >  	case STOP_POWER_OFF:
> > -		val |= 0x2 << BP_CLPCR_LPM;
> > -		val |= 0x3 << BP_CLPCR_STBY_COUNT;
> > -		val |= BM_CLPCR_VSTBY;
> > -		val |= BM_CLPCR_SBYOS;
> > +		clpcr |= 0x2 << BP_CLPCR_LPM;
> > +		clpcr |= 0x3 << BP_CLPCR_STBY_COUNT;
> > +		clpcr |= BM_CLPCR_VSTBY;
> > +		clpcr |= BM_CLPCR_SBYOS;
> > +		break;
> > +	case ARM_POWER_OFF:
> 
> I'm unsure we need this new state.
> 
> > +		clpcr |= 0x2 << BP_CLPCR_LPM;
> > +		clpcr |= 0x3 << BP_CLPCR_STBY_COUNT;
> > +		clpcr |= BM_CLPCR_VSTBY;
> > +		clpcr |= BM_CLPCR_SBYOS;
> > +		clpcr |= BM_CLPCR_WB_PER_AT_LPM;
> > +		/* assert anatop_reg_bypass signal */
> > +		ccr |= BM_CCR_RBC_EN;
> 
> It seems that the difference between STOP_POWER_OFF and ARM_POWER_OFF
> is all about bits BM_CLPCR_WB_PER_AT_LPM and BM_CCR_RBC_EN.  Can you
> elaborate why these two bits need to be set for suspend with DDR in
> self-refresh state?
> 
> >  		break;
> >  	default:
> >  		return -EINVAL;
> >  	}
> > -	writel_relaxed(val, CLPCR);
> > +	writel_relaxed(clpcr, CLPCR);
> > +	writel_relaxed(ccr, CCR);
> >  
> >  	return 0;
> >  }
> > diff --git a/arch/arm/mach-imx/gpc.c b/arch/arm/mach-imx/gpc.c
> > index e1537f9..8fc255b 100644
> > --- a/arch/arm/mach-imx/gpc.c
> > +++ b/arch/arm/mach-imx/gpc.c
> > @@ -17,15 +17,36 @@
> >  #include <linux/of_irq.h>
> >  #include <asm/hardware/gic.h>
> >  
> > +#define GPC_CNTR		0x000
> 
> Where is it used?
> 
> >  #define GPC_IMR1		0x008
> > +#define GPC_ISR1		0x018
> > +#define GPC_ISR2		0x01c
> > +#define GPC_ISR3		0x020
> > +#define GPC_ISR4		0x024
> 
> It seems that only definition GPC_ISR1 is used?
> 
> >  #define GPC_PGC_CPU_PDN		0x2a0
> >  
> >  #define IMR_NUM			4
> > +#define ISR_NUM			4
> >  
> >  static void __iomem *gpc_base;
> >  static u32 gpc_wake_irqs[IMR_NUM];
> >  static u32 gpc_saved_imrs[IMR_NUM];
> >  
> > +bool imx_gpc_wake_irq_pending(void)
> > +{
> > +	void __iomem *reg_isr1 = gpc_base + GPC_ISR1;
> > +	int i;
> > +	u32 val;
> > +
> > +	for (i = 0; i < ISR_NUM; i++) {
> > +		val = readl_relaxed(reg_isr1 + i * 4);
> > +		if (val & gpc_wake_irqs[i])
> > +			return true;
> > +	}
> > +
> > +	return false;
> > +}
> > +
> >  void imx_gpc_pre_suspend(void)
> >  {
> >  	void __iomem *reg_imr1 = gpc_base + GPC_IMR1;
> > diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c
> > index f20f191..6e45245 100644
> > --- a/arch/arm/mach-imx/pm-imx6q.c
> > +++ b/arch/arm/mach-imx/pm-imx6q.c
> > @@ -13,31 +13,73 @@
> >  #include <linux/init.h>
> >  #include <linux/io.h>
> >  #include <linux/of.h>
> > +#include <linux/of_address.h>
> >  #include <linux/suspend.h>
> >  #include <asm/cacheflush.h>
> >  #include <asm/proc-fns.h>
> >  #include <asm/suspend.h>
> > +#include <asm/mach/map.h>
> >  #include <asm/hardware/cache-l2x0.h>
> > +#include <mach/iram.h>
> >  #include <mach/common.h>
> >  #include <mach/hardware.h>
> >  
> > +struct imx_iram_pm {
> > +	void *iram_cpaddr;
> > +	unsigned long suspend_iram_paddr;
> > +	unsigned long suspend_iram_size;
> > +	void *suspend_iram_vaddr;
> > +	void *reg_ptr[4];
> > +} imx6q_iram_pm;
> > +
> >  extern unsigned long phys_l2x0_saved_regs;
> > +extern void imx6q_suspend(void);
> > +static void (*suspend_in_iram)(unsigned long iram_paddr,
> > +				unsigned long iram_vaddr,
> > +				unsigned long iram_size);
> >  
> >  static int imx6q_suspend_finish(unsigned long val)
> >  {
> > -	cpu_do_idle();
> > +	if ((val == PM_SUSPEND_MEM) && suspend_in_iram) {
> > +		suspend_in_iram((unsigned long)imx6q_iram_pm.suspend_iram_paddr,
> > +				(unsigned long)imx6q_iram_pm.suspend_iram_vaddr,
> > +				(unsigned long)imx6q_iram_pm.suspend_iram_size);
> > +	} else
> 
> The brace pair {} is not needed.
> 
> > +		cpu_do_idle();
> > +
> >  	return 0;
> >  }
> >  
> > +static void imx6q_prepare_suspend_iram(void)
> > +{
> > +	unsigned long *iram_stack = imx6q_iram_pm.suspend_iram_vaddr
> > +					+ imx6q_iram_pm.suspend_iram_size;
> > +
> > +	*(--iram_stack) = (unsigned long)imx6q_iram_pm.reg_ptr[3];
> > +	*(--iram_stack) = (unsigned long)imx6q_iram_pm.reg_ptr[2];
> > +	*(--iram_stack) = (unsigned long)imx6q_iram_pm.reg_ptr[1];
> > +	*(--iram_stack) = (unsigned long)imx6q_iram_pm.reg_ptr[0];
> > +}
> > +
> 
> I'm not sure we need to do this.  I feel we have done too much in
> suspend_in_iram().  See comments on suspend_in_iram below.
> 
> >  static int imx6q_pm_enter(suspend_state_t state)
> >  {
> >  	switch (state) {
> > +	case PM_SUSPEND_STANDBY:
> >  	case PM_SUSPEND_MEM:
> > -		imx6q_set_lpm(STOP_POWER_OFF);
> > +		if (imx_gpc_wake_irq_pending())
> > +			return 0;
> > +
> > +		if (state == PM_SUSPEND_STANDBY)
> > +			imx6q_set_lpm(STOP_POWER_OFF);
> > +		else
> > +			imx6q_set_lpm(ARM_POWER_OFF);
> > +
> 
> I do not think we need to distinguish these two states, STOP_POWER_OFF
> and ARM_POWER_OFF.  When I added STOP_POWER_OFF support, the DDR self
> refresh support was missed there.  When this feature is available, we
> can just add it on top of STOP_POWER_OFF rather than inventing a new
> state.
> 
> >  		imx_gpc_pre_suspend();
> >  		imx_set_cpu_jump(0, v7_cpu_resume);
> > +		if (state == PM_SUSPEND_MEM)
> > +			imx6q_prepare_suspend_iram();
> >  		/* Zzz ... */
> > -		cpu_suspend(0, imx6q_suspend_finish);
> > +		cpu_suspend(state, imx6q_suspend_finish);
> >  		imx_smp_prepare();
> >  		imx_gpc_post_resume();
> >  		break;
> > @@ -48,11 +90,55 @@ static int imx6q_pm_enter(suspend_state_t state)
> >  	return 0;
> >  }
> >  
> > +static int imx6q_pm_valid(suspend_state_t state)
> > +{
> > +	return (state > PM_SUSPEND_ON && state <= PM_SUSPEND_MAX);
> > +}
> > +
> >  static const struct platform_suspend_ops imx6q_pm_ops = {
> >  	.enter = imx6q_pm_enter,
> > -	.valid = suspend_valid_only_mem,
> > +	.valid = imx6q_pm_valid,
> >  };
> >  
> > +static int __init imx6q_pm_iram_of_init(void)
> > +{
> > +	struct device_node *np;
> > +
> > +	/*
> > +	 * these register may already ioremaped, need figure out
> > +	 * one way to save vmalloc space.
> > +	 */
> > +	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-src");
> > +	imx6q_iram_pm.reg_ptr[0] = of_iomap(np, 0);
> > +	if (!imx6q_iram_pm.reg_ptr[0])
> > +		goto err0;
> > +
> > +	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-iomuxc");
> > +	imx6q_iram_pm.reg_ptr[1] = of_iomap(np, 0);
> > +	if (!imx6q_iram_pm.reg_ptr[1])
> > +		goto err1;
> > +
> > +	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-mmdc");
> > +	imx6q_iram_pm.reg_ptr[2] = of_iomap(np, 0);
> > +	if (!imx6q_iram_pm.reg_ptr[2])
> > +		goto err2;
> > +
> > +	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-anatop");
> > +	imx6q_iram_pm.reg_ptr[3] = of_iomap(np, 0);
> > +	if (!imx6q_iram_pm.reg_ptr[3])
> > +		goto err3;
> 
> This is not really nice and necessary, if we can limit the work done
> in suspend_in_iram().
> 
> > +
> > +	return 0;
> > +err3:
> > +	iounmap(imx6q_iram_pm.reg_ptr[2]);
> > +err2:
> > +	iounmap(imx6q_iram_pm.reg_ptr[1]);
> > +err1:
> > +	iounmap(imx6q_iram_pm.reg_ptr[0]);
> > +err0:
> > +	return -EINVAL;
> > +}
> > +
> >  void __init imx6q_pm_init(void)
> >  {
> >  	/*
> > @@ -67,4 +153,38 @@ void __init imx6q_pm_init(void)
> >  	phys_l2x0_saved_regs = __pa(&l2x0_saved_regs);
> >  
> >  	suspend_set_ops(&imx6q_pm_ops);
> > +
> > +	/* Move suspend routine into iRAM */
> > +	imx6q_iram_pm.suspend_iram_size = SZ_4K;
> > +	imx6q_iram_pm.iram_cpaddr = iram_alloc(imx6q_iram_pm.suspend_iram_size,
> > +			&imx6q_iram_pm.suspend_iram_paddr);
> > +	if (imx6q_iram_pm.iram_cpaddr) {
> > +		if (imx6q_pm_iram_of_init() < 0) {
> > +			iram_free(imx6q_iram_pm.suspend_iram_paddr,
> > +					imx6q_iram_pm.suspend_iram_size);
> > +			return;
> > +		}
> > +		/*
> > +		 * Need to remap the area here since we want the memory region
> > +		 * to be noncached & executable.
> > +		 */
> > +		imx6q_iram_pm.suspend_iram_vaddr =
> > +			__arm_ioremap(imx6q_iram_pm.suspend_iram_paddr,
> > +					imx6q_iram_pm.suspend_iram_size,
> > +					MT_MEMORY_NONCACHED);
> > +		pr_info("cpaddr = %p suspend_iram_base=%p\n",
> 
> pr_debug?
> 
> > +				imx6q_iram_pm.iram_cpaddr,
> > +				imx6q_iram_pm.suspend_iram_vaddr);
> > +
> > +		/*
> > +		 * Need to run the suspend code from IRAM as the DDR needs
> > +		 * to be put into low power mode manually.
> > +		 */
> > +		memcpy(imx6q_iram_pm.iram_cpaddr, imx6q_suspend,
> > +					imx6q_iram_pm.suspend_iram_size);
> 
> Please try to use fncpy (arch/arm/include/asm/fncpy.h)
> 
> > +
> > +		suspend_in_iram = (void *)imx6q_iram_pm.suspend_iram_vaddr;
> > +
> > +	} else
> > +		suspend_in_iram = NULL;
> 
> The suspend_in_iram is already initialized as NULL, I guess.
> 
> >  }
> > diff --git a/arch/arm/mach-imx/suspend-imx6q.S b/arch/arm/mach-imx/suspend-imx6q.S
> > new file mode 100644
> > index 0000000..f803e2b
> > --- /dev/null
> > +++ b/arch/arm/mach-imx/suspend-imx6q.S
> > @@ -0,0 +1,308 @@
> > +/*
> > + * Copyright 2011 Freescale Semiconductor, Inc.
> > + * Copyright 2011 Linaro Ltd.
> > + *
> > + * The code contained herein is licensed under the GNU General Public
> > + * License. You may obtain a copy of the GNU General Public License
> > + * Version 2 or later at the following locations:
> > + *
> > + * http://www.opensource.org/licenses/gpl-license.html
> > + * http://www.gnu.org/copyleft/gpl.html
> > + */
> > +
> > +#include <linux/linkage.h>
> > +#include <mach/hardware.h>
> > +#include <asm/hardware/cache-l2x0.h>
> > +
> > +#define SRC_GPR1_OFFSET		0x020
> > +#define SRC_GPR2_OFFSET		0x024
> > +#define MMDC_MAPSR_OFFSET 	0x404
> > +#define MMDC_MAPSR_PSS 		(1 << 4)
> > +#define MMDC_MAPSR_PSD 		(1 << 0)
> > +#define ANATOP_REG_2P5		0x130
> > +
> > +.macro	ddr_io_save
> > +	ldr	r4, [r9, #0x5ac] /* DRAM_DQM0 */
> 
> If we have macro defined for DRAM_DQM0, we can save the magic number
> and the comment.  It applies to the same cases all over the ddr_io_xxx
> functions.
> 
> > +	ldr	r5, [r9, #0x5b4] /* DRAM_DQM1 */
> > +	ldr	r6, [r9, #0x528] /* DRAM_DQM2 */
> > +	ldr	r7, [r9, #0x520] /* DRAM_DQM3 */
> > +	stmfd	sp!, {r4-r7}
> > +
> > +	ldr	r4, [r9, #0x514] /* DRAM_DQM4 */
> > +	ldr	r5, [r9, #0x510] /* DRAM_DQM5 */
> > +	ldr	r6, [r9, #0x5bc] /* DRAM_DQM6 */
> > +	ldr	r7, [r9, #0x5c4] /* DRAM_DQM7 */
> > +	stmfd	sp!, {r4-r7}
> > +
> > +	ldr	r4, [r9, #0x56c] /* DRAM_CAS */
> > +	ldr	r5, [r9, #0x578] /* DRAM_RAS */
> > +	ldr	r6, [r9, #0x588] /* DRAM_SDCLK_0 */
> > +	ldr	r7, [r9, #0x594] /* DRAM_SDCLK_1 */
> > +	stmfd	sp!, {r4-r7}
> > +
> > +	ldr	r5, [r9, #0x750] /* DDRMODE_CTL */
> > +	ldr	r6, [r9, #0x774] /* DDRMODE */
> > +	stmfd	sp!, {r5-r6}
> > +
> > +	ldr	r4, [r9, #0x5a8] /* DRAM_SDQS0 */
> > +	ldr	r5, [r9, #0x5b0] /* DRAM_SDQS1 */
> > +	ldr	r6, [r9, #0x524] /* DRAM_SDQS2 */
> > +	ldr	r7, [r9, #0x51c] /* DRAM_SDQS3 */
> > +	stmfd	sp!, {r4-r7}
> > +
> > +	ldr	r4, [r9, #0x518] /* DRAM_SDQS4 */
> > +	ldr	r5, [r9, #0x50c] /* DRAM_SDQS5 */
> > +	ldr	r6, [r9, #0x5b8] /* DRAM_SDQS6 */
> > +	ldr	r7, [r9, #0x5c0] /* DRAM_SDQS7 */
> > +	stmfd	sp!, {r4-r7}
> > +
> > +	ldr	r4, [r9, #0x784] /* GPR_B0DS */
> > +	ldr	r5, [r9, #0x788] /* GPR_B1DS */
> > +	ldr	r6, [r9, #0x794] /* GPR_B2DS */
> > +	ldr	r7, [r9, #0x79c] /* GPR_B3DS */
> > +	stmfd	sp!, {r4-r7}
> > +
> > +	ldr	r4, [r9, #0x7a0] /* GPR_B4DS */
> > +	ldr	r5, [r9, #0x7a4] /* GPR_B5DS */
> > +	ldr	r6, [r9, #0x7a8] /* GPR_B6DS */
> > +	ldr	r7, [r9, #0x748] /* GPR_B7DS */
> > +	stmfd	sp!, {r4-r7}
> > +
> > +	ldr	r5, [r9, #0x74c] /* GPR_ADDS*/
> > +	ldr	r6, [r9, #0x59c] /* DRAM_SODT0*/
> > +	ldr	r7, [r9, #0x5a0] /* DRAM_SODT1*/
> > +	stmfd	sp!, {r5-r7}
> > +.endm
> > +
> > +.macro	ddr_io_restore
> > +	ldmfd	sp!, {r5-r7}
> > +	str	r5, [r9, #0x74c] /* GPR_ADDS*/
> > +	str	r6, [r9, #0x59c] /* DRAM_SODT0*/
> > +	str	r7, [r9, #0x5a0] /* DRAM_SODT1*/
> > +
> > +	ldmfd	sp!, {r4-r7}
> > +	str	r4, [r9, #0x7a0] /* GPR_B4DS */
> > +	str	r5, [r9, #0x7a4] /* GPR_B5DS */
> > +	str	r6, [r9, #0x7a8] /* GPR_B6DS */
> > +	str	r7, [r9, #0x748] /* GPR_B7DS */
> > +
> > +	ldmfd	sp!, {r4-r7}
> > +	str	r4, [r9, #0x784] /* GPR_B0DS */
> > +	str	r5, [r9, #0x788] /* GPR_B1DS */
> > +	str	r6, [r9, #0x794] /* GPR_B2DS */
> > +	str	r7, [r9, #0x79c] /* GPR_B3DS */
> > +
> > +	ldmfd	sp!, {r4-r7}
> > +	str	r4, [r9, #0x518] /* DRAM_SDQS4 */
> > +	str	r5, [r9, #0x50c] /* DRAM_SDQS5 */
> > +	str	r6, [r9, #0x5b8] /* DRAM_SDQS6 */
> > +	str	r7, [r9, #0x5c0] /* DRAM_SDQS7 */
> > +
> > +	ldmfd	sp!, {r4-r7}
> > +	str	r4, [r9, #0x5a8] /* DRAM_SDQS0 */
> > +	str	r5, [r9, #0x5b0] /* DRAM_SDQS1 */
> > +	str	r6, [r9, #0x524] /* DRAM_SDQS2 */
> > +	str	r7, [r9, #0x51c] /* DRAM_SDQS3 */
> > +
> > +	ldmfd	sp!, {r5-r6}
> > +	str	r5, [r9, #0x750] /* DDRMODE_CTL */
> > +	str	r6, [r9, #0x774] /* DDRMODE */
> > +
> > +	ldmfd	sp!, {r4-r7}
> > +	str	r4, [r9, #0x56c] /* DRAM_CAS */
> > +	str	r5, [r9, #0x578] /* DRAM_RAS */
> > +	str	r6, [r9, #0x588] /* DRAM_SDCLK_0 */
> > +	str	r7, [r9, #0x594] /* DRAM_SDCLK_1 */
> > +
> > +	ldmfd	sp!, {r4-r7}
> > +	str	r4, [r9, #0x514] /* DRAM_DQM4 */
> > +	str	r5, [r9, #0x510] /* DRAM_DQM5 */
> > +	str	r6, [r9, #0x5bc] /* DRAM_DQM6 */
> > +	str	r7, [r9, #0x5c4] /* DRAM_DQM7 */
> > +
> > +	ldmfd	sp!, {r4-r7}
> > +	str	r4, [r9, #0x5ac] /* DRAM_DQM0 */
> > +	str	r5, [r9, #0x5b4] /* DRAM_DQM1 */
> > +	str	r6, [r9, #0x528] /* DRAM_DQM2 */
> > +	str	r7, [r9, #0x520] /* DRAM_DQM3 */
> > +.endm
> > +
> > +.macro	ddr_io_set_lpm
> > +	mov	r4, #0
> > +	str	r4, [r9, #0x5ac] /* DRAM_DQM0 */
> > +	str	r4, [r9, #0x5b4] /* DRAM_DQM1 */
> > +	str	r4, [r9, #0x528] /* DRAM_DQM2 */
> > +	str	r4, [r9, #0x520] /* DRAM_DQM3 */
> > +
> > +	str	r4, [r9, #0x514] /* DRAM_DQM4 */
> > +	str	r4, [r9, #0x510] /* DRAM_DQM5 */
> > +	str	r4, [r9, #0x5bc] /* DRAM_DQM6 */
> > +	str	r4, [r9, #0x5c4] /* DRAM_DQM7 */
> > +
> > +	str	r4, [r9, #0x56c] /* DRAM_CAS */
> > +	str	r4, [r9, #0x578] /* DRAM_RAS */
> > +	str	r4, [r9, #0x588] /* DRAM_SDCLK_0 */
> > +	str	r4, [r9, #0x594] /* DRAM_SDCLK_1 */
> > +
> > +	str	r4, [r9, #0x750] /* DDRMODE_CTL */
> > +	str	r4, [r9, #0x774] /* DDRMODE */
> > +
> > +	str	r4, [r9, #0x5a8] /* DRAM_SDQS0 */
> > +	str	r4, [r9, #0x5b0] /* DRAM_SDQS1 */
> > +	str	r4, [r9, #0x524] /* DRAM_SDQS2 */
> > +	str	r4, [r9, #0x51c] /* DRAM_SDQS3 */
> > +
> > +	str	r4, [r9, #0x518] /* DRAM_SDQS4 */
> > +	str	r4, [r9, #0x50c] /* DRAM_SDQS5 */
> > +	str	r4, [r9, #0x5b8] /* DRAM_SDQS6 */
> > +	str	r4, [r9, #0x5c0] /* DRAM_SDQS7 */
> > +
> > +	str	r4, [r9, #0x784] /* GPR_B0DS */
> > +	str	r4, [r9, #0x788] /* GPR_B1DS */
> > +	str	r4, [r9, #0x794] /* GPR_B2DS */
> > +	str	r4, [r9, #0x79c] /* GPR_B3DS */
> > +
> > +	str	r4, [r9, #0x7a0] /* GPR_B4DS */
> > +	str	r4, [r9, #0x7a4] /* GPR_B5DS */
> > +	str	r4, [r9, #0x7a8] /* GPR_B6DS */
> > +	str	r4, [r9, #0x748] /* GPR_B7DS */
> > +
> > +	str	r4, [r9, #0x74c] /* GPR_ADDS*/
> > +	str	r4, [r9, #0x59c] /* DRAM_SODT0*/
> > +	str	r4, [r9, #0x5a0] /* DRAM_SODT1*/
> > +.endm
> > +
> > +/*
> > + * imx6q_suspend:
> > + *
> > + * Suspend the processor (eg, wait for interrupt).
> > + * Set the DDR into Self Refresh
> > + * IRQs are already disabled.
> > + *
> > + * Registers usage in the imx6q_suspend:
> > + *
> > + * r0: suspend_iram_paddr
> > + * r1: suspend_iram_vaddr
> > + * r2: suspend_iram_size
> > + *
> > + * r8: src_base pointer
> > + * r9: iomux_base pointer
> > + * r10: mmdc_base pointer
> > + * r11: anatop_base pointer
> > + * sp: iram stack
> > + *
> > + * Corrupted registers: r0-r3
> > + */
> > +
> > +ENTRY(imx6q_suspend)
> > +	mov	r3, sp				@ save sp
> > +	add	sp, r1, r2			@ set sp to top iram stack
> > +	sub	sp, sp, #16	 		@ 4 regs ptr
> > +	stmfd	sp!, {r4 - r12, lr}		@ save registers
> > +
> > +	add	r4, r1, r2
> > +	ldr	r8, [r4, #-16]			@ r8 = src_base pointer
> > +	ldr	r9, [r4, #-12]			@ r9 = iomux_base pointer
> > +	ldr	r10, [r4, #-8]			@ r10 = mmdc_base pointer
> > +	ldr	r11, [r4, #-4]			@ r11 = anatop_base pointer
> > +
> > +	/* should not access sp in ddr until resume with cache MMU on */
> > +	stmfd	sp!, {r3}			@ save old sp
> > +
> > +	ldr	r4, [r8, #SRC_GPR1_OFFSET]	@ r8 = src_base pointer
> > +	stmfd	sp!, {r4}			@ save old resume func
> > +
> > +	/* Enable weak 2P5 linear regulator */
> > +	ldr	r4, [r11, #ANATOP_REG_2P5]	@ r11 = anatop_base pointer
> > +	orr	r4, r4, #0x40000
> > +	str	r4, [r11, #ANATOP_REG_2P5]
> > +	mov	r6, #1
> > +wait:	ldr	r4, [r11, #ANATOP_REG_2P5]
> > +	and	r4, r4, r6, lsl #17			@ output ok?
> > +	cmp	r4, #0
> > +	beq	wait
> > +
> > +	/* save ddr iomux regs */
> > +	ddr_io_save
> > +
> 
> Do we really need to have all above codes running in iram?  My
> understanding is only the portion of the codes that actually puts
> DDR into self-refresh state and the codes after that need to run
> in iram.
> 
> > +	/* set ddr to low power mode */
> > +	ldr	r4, [r10, #MMDC_MAPSR_OFFSET]	@ r10 = mmdc_base pointer
> > +	bic	r4, #MMDC_MAPSR_PSD
> > +	str	r4, [r10, #MMDC_MAPSR_OFFSET]
> > +refresh:
> > +	ldr	r4, [r10, #MMDC_MAPSR_OFFSET]
> > +	and	r4, r4, #MMDC_MAPSR_PSS
> > +	cmp	r4, #0
> > +	beq	refresh
> > +
> > +	ddr_io_set_lpm
> > +
> > +	/* save resume pointer into SRC_GPR1, sp pointer into SRC_GPR2 */
> > +	ldr	r4, =imx6q_suspend
> > +	ldr	r5, =imx6q_resume
> > +	sub	r5, r5, r4			@ r5 = resmue offset
> > +	add	r5, r0, r5			@ r0 = suspend_iram_paddr, r5 = resmue phy addr
> > +	str	r5, [r8, #SRC_GPR1_OFFSET]	@ r8 = src_base pointer
> > +	sub	r5, sp, r1			@ r1 = suspend_iram_vaddr, r5 = sp offset
> > +	add	r5, r0, r5			@ r0 = suspend_iram_paddr, r5 = sp phy addr
> > +	str	r5, [r8, #SRC_GPR2_OFFSET]	@ r8 = src_base pointer
> > +
> > +	/* execute a wfi instruction to let SOC go into stop mode */
> > +	dsb
> > +	wfi
> > +
> > +	nop
> > +	nop
> > +	nop
> > +	nop
> > +
> > +	/*
> > +	 * if go here, means there is a wakeup irq pending, we should resume
> > +	 * system immediately.
> > +	 */
> 
> I'm wondering how this will happen exactly.  Is this a real case in
> practical world?  If yes, do you have the steps to reproduce it?  I'm
> actually asking if this resume path has been tested yet.
> 
> > +	ddr_io_restore
> > +
> > +	/* Disable weak 2P5 linear regulator */
> > +	ldr	r4, [r11, #ANATOP_REG_2P5]	@ r11 = anatop_base pointer
> > +	bic	r4, #0x40000
> > +	str	r4, [r11, #ANATOP_REG_2P5]
> > +
> > +	ldmfd	sp!, {r4}			@ drop old resmue func ptr
> > +	ldmfd	sp!, {r3}
> > +	ldmfd	sp!, {r4 - r12, lr}
> > +	mov	sp, r3
> > +	mov	pc, lr
> > +
> > +/*
> > + * when SOC exit stop mode, arm core restart from here, currently
> > + * are running with MMU off.
> > + */
> > +imx6q_resume:
> > +	ldr	r0, =MX6Q_SRC_BASE_ADDR
> > +	mov	r1, #0x0
> > +	str	r1, [r0, #SRC_GPR1_OFFSET] 	@ clear SRC_GPR1
> > +	ldr	sp, [r0, #SRC_GPR2_OFFSET]
> > +	str	r1, [r0, #SRC_GPR2_OFFSET]	@ clear SRC_GPR2
> > +
> > +	ldr	r9, =MX6Q_IOMUXC_BASE_ADDR
> > +	ddr_io_restore
> > +
> > +	ldr	r0, =MX6Q_MMDC0_BASE_ADDR
> > +	ldr	r1, [r0, #MMDC_MAPSR_OFFSET]
> > +	orr	r1, #MMDC_MAPSR_PSD
> > +	str	r1, [r0, #MMDC_MAPSR_OFFSET]
> > +
> > +	/* Disable weak 2P5 linear regulator */
> > +	ldr	r0, =MX6Q_ANATOP_BASE_ADDR
> > +	ldr	r1, [r0, #ANATOP_REG_2P5]
> > +	bic	r1, #0x40000
> > +	str	r1, [r0, #ANATOP_REG_2P5]
> > +
> > +	ldmfd	sp!, {r2}			@ resmue func ptr
> > +	ldmfd	sp!, {r3}
> > +	ldmfd	sp!, {r4 - r12, lr}
> > +	mov	sp, r3
> > +
> > +	/* return back */
> > +	mov	pc, r2
> > +ENDPROC(imx6q_suspend)
> > diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h
> > index 83cca9b..0e1e652 100644
> > --- a/arch/arm/plat-mxc/include/mach/common.h
> > +++ b/arch/arm/plat-mxc/include/mach/common.h
> > @@ -82,6 +82,7 @@ enum mxc_cpu_pwr_mode {
> >  	WAIT_UNCLOCKED_POWER_OFF,	/* WAIT + SRPG */
> >  	STOP_POWER_ON,		/* just STOP */
> >  	STOP_POWER_OFF,		/* STOP + SRPG */
> > +	ARM_POWER_OFF,          /* STOP + SRPG + ARM power off */
> 
> I'm not sure that we need this new mode at all.  From the comment,
> the 'ARM power off' is the difference between ARM_POWER_OFF and
> STOP_POWER_OFF.  But it's not really the case.
> 
> Regards,
> Shawn
> 
> >  };
> >  
> >  extern void mx5_cpu_lp_set(enum mxc_cpu_pwr_mode mode);
> > @@ -123,6 +124,7 @@ extern void imx_set_cpu_jump(int cpu, void *jump_addr);
> >  extern void imx_src_init(void);
> >  extern void imx_src_prepare_restart(void);
> >  extern void imx_gpc_init(void);
> > +extern bool imx_gpc_wake_irq_pending(void);
> >  extern void imx_gpc_pre_suspend(void);
> >  extern void imx_gpc_post_resume(void);
> >  extern void imx51_babbage_common_init(void);
> > diff --git a/arch/arm/plat-mxc/include/mach/mx6q.h b/arch/arm/plat-mxc/include/mach/mx6q.h
> > index 254a561..eea2968 100644
> > --- a/arch/arm/plat-mxc/include/mach/mx6q.h
> > +++ b/arch/arm/plat-mxc/include/mach/mx6q.h
> > @@ -27,6 +27,12 @@
> >  #define MX6Q_CCM_SIZE			0x4000
> >  #define MX6Q_ANATOP_BASE_ADDR		0x020c8000
> >  #define MX6Q_ANATOP_SIZE		0x1000
> > +#define MX6Q_SRC_BASE_ADDR		0x020d8000
> > +#define MX6Q_SRC_SIZE			0x4000
> > +#define MX6Q_IOMUXC_BASE_ADDR		0x020e0000
> > +#define MX6Q_IOMUXC_SIZE		0x4000
> > +#define MX6Q_MMDC0_BASE_ADDR 		0x021b0000
> > +#define MX6Q_MMDC0_SIZE 		0x4000
> >  #define MX6Q_UART4_BASE_ADDR		0x021f0000
> >  #define MX6Q_UART4_SIZE			0x4000
> >  
> > -- 
> > 1.7.4.1
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>