Subject: [PATCH 3/4] ARM: OMAP2: gpmc: Add support for BCH ECC scheme

From: [email-masked] (Ivan Djelic)
Date: Wed, 3 Oct 2012 20:54:58 +0200

On Wed, Oct 03, 2012 at 03:29:48PM +0100, Philip, Avinash wrote:
> Add support for BCH ECC scheme to gpmc driver and also enabling multi
> sector read/write. This helps in doing single shot NAND page read and
> write.
> 
> ECC engine configurations
> BCH 4 bit support
> 1. write => ECC engine configured in wrap mode 6 and with ecc_size0 as 32.
> 2. read  => ECC engine configured in wrap mode 1 and with ecc_size0 as
> 13 and ecc_size1 as 1.
> 
> BCH 8 bit support
> 1. write => ECC engine configured in wrap mode 6 and with ecc_size0 as 32.
> 2. read  => ECC engine configured in wrap mode 1 and with ecc_size0 as
> 26 and ecc_size1 as 2.
> 
> Note: For BCH8 ECC bytes set to 14 to make compatible with RBL.
> 

Hi Philip,

I have a few comments/questions below,

(...)
> diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
> index 72428bd..c9bc3cf 100644
> --- a/arch/arm/mach-omap2/gpmc.c
> +++ b/arch/arm/mach-omap2/gpmc.c
> @@ -24,6 +24,7 @@
>  #include <linux/io.h>
>  #include <linux/module.h>
>  #include <linux/interrupt.h>
> +#include <linux/mtd/nand.h>
>  
>  #include <asm/mach-types.h>
>  #include <plat/gpmc.h>
> @@ -83,6 +84,18 @@
>  #define ENABLE_PREFETCH		(0x1 << 7)
>  #define DMA_MPU_MODE		2
>  
> +/* GPMC ecc engine settings for read */
> +#define BCH_WRAPMODE_1		1	/* BCH wrap mode 6 */

Comment should say "mode 1".

(...)
>  /**
> + * gpmc_calculate_ecc_bch	- Generate ecc bytes per block of 512 data bytes for entire page
> + * @cs:  chip select number
> + * @dat: The pointer to data on which ECC is computed
> + * @ecc: The ECC output buffer
> + */
> +int gpmc_calculate_ecc_bch(int cs, const u_char *dat, u_char *ecc)
> +{
> +	int i, eccbchtsel;
> +	u32 nsectors, reg, bch_val1, bch_val2, bch_val3, bch_val4;
> +
> +	if (gpmc_ecc_used != cs)
> +		return -EINVAL;
> +
> +	/* read number of sectors for ecc to be calculated */
> +	nsectors = ((gpmc_read_reg(GPMC_ECC_CONFIG) >> 4) & 0x7) + 1;
> +	/*
> +	 * find BCH scheme used
> +	 * 0 -> BCH4
> +	 * 1 -> BCH8
> +	 */
> +	eccbchtsel = ((gpmc_read_reg(GPMC_ECC_CONFIG) >> 12) & 0x3);
> +
> +	/* update ecc bytes for entire page */
> +	for (i = 0; i < nsectors; i++) {
> +
> +		reg = GPMC_ECC_BCH_RESULT_0 + 16 * i;
> +
> +		/* Read hw-computed remainder */
> +		bch_val1 = gpmc_read_reg(reg + 0);
> +		bch_val2 = gpmc_read_reg(reg + 4);
> +		if (eccbchtsel) {
> +			bch_val3 = gpmc_read_reg(reg + 8);
> +			bch_val4 = gpmc_read_reg(reg + 12);
> +		}
> +
> +		if (eccbchtsel) {
> +			/* BCH8 ecc scheme */
> +			*ecc++ = (bch_val4 & 0xFF);
> +			*ecc++ = ((bch_val3 >> 24) & 0xFF);
> +			*ecc++ = ((bch_val3 >> 16) & 0xFF);
> +			*ecc++ = ((bch_val3 >> 8) & 0xFF);
> +			*ecc++ = (bch_val3 & 0xFF);
> +			*ecc++ = ((bch_val2 >> 24) & 0xFF);
> +			*ecc++ = ((bch_val2 >> 16) & 0xFF);
> +			*ecc++ = ((bch_val2 >> 8) & 0xFF);
> +			*ecc++ = (bch_val2 & 0xFF);
> +			*ecc++ = ((bch_val1 >> 24) & 0xFF);
> +			*ecc++ = ((bch_val1 >> 16) & 0xFF);
> +			*ecc++ = ((bch_val1 >> 8) & 0xFF);
> +			*ecc++ = (bch_val1 & 0xFF);
> +			/* 14th byte of ecc not used */
> +			*ecc++ = 0;
> +		} else {
> +			/* BCH4 ecc scheme */
> +			*ecc++ = ((bch_val2 >> 12) & 0xFF);
> +			*ecc++ = ((bch_val2 >> 4) & 0xFF);
> +			*ecc++ = (((bch_val2 & 0xF) << 4) |
> +					((bch_val1 >> 28) & 0xF));
> +			*ecc++ = ((bch_val1 >> 20) & 0xFF);
> +			*ecc++ = ((bch_val1 >> 12) & 0xFF);
> +			*ecc++ = ((bch_val1 >> 4) & 0xFF);
> +			*ecc++ = ((bch_val1 & 0xF) << 4);
> +		}
> +	}
> +
> +	gpmc_ecc_used = -EINVAL;
> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(gpmc_calculate_ecc_bch);

Here you introduce a function very similar to gpmc_calculate_ecc_bch4 and
gpmc_calculate_ecc_bch8, but without the added benefit (IMHO) of the constant
polynomial that allows to get an ecc sequence of 0xFFs for a buffer filled with
0xFFs. Why ?
If using the ELM prevents you from reusing gpmc_calculate_ecc_bch[48], could you explain in which way ?

Best regards,
--
Ivan