Subject: [linux-sunxi] [PATCH 2/8] clocksource: sun4i: Add clocksource and sched clock drivers

From: [email-masked] (Siarhei Siamashka)
Date: Thu, 27 Jun 2013 22:51:01 +0300

On Thu, 27 Jun 2013 19:02:28 +0200
Maxime Ripard <[email-masked]> wrote:

> Hi Siarhei,
> 
> On Thu, Jun 27, 2013 at 01:17:29PM +0300, Siarhei Siamashka wrote:
> > On Wed, 26 Jun 2013 23:16:55 +0200
> > Maxime Ripard <[email-masked]> wrote:
> > 
> > > The A10 and the A13 has a 64 bits free running counter that we can use
> > > as a clocksource and a sched clock, that were both not used yet on these
> > > platforms.
> > > 
> > > Signed-off-by: Maxime Ripard <[email-masked]>
> > > ---
> > >  drivers/clocksource/sun4i_timer.c | 27 +++++++++++++++++++++++++++
> > >  1 file changed, 27 insertions(+)
> > > 
> > > diff --git a/drivers/clocksource/sun4i_timer.c b/drivers/clocksource/sun4i_timer.c
> > > index bdf34d9..1d2eaa0 100644
> > > --- a/drivers/clocksource/sun4i_timer.c
> > > +++ b/drivers/clocksource/sun4i_timer.c
> > > @@ -23,6 +23,8 @@
> > >  #include <linux/of_address.h>
> > >  #include <linux/of_irq.h>
> > >  
> > > +#include <asm/sched_clock.h>
> > > +
> > >  #define TIMER_IRQ_EN_REG	0x00
> > >  #define TIMER_IRQ_EN(val)		BIT(val)
> > >  #define TIMER_IRQ_ST_REG	0x04
> > > @@ -34,6 +36,11 @@
> > >  #define TIMER_CNTVAL_REG(val)	(0x10 * val + 0x18)
> > >  
> > >  #define TIMER_SCAL		16
> > > +#define TIMER_CNT64_CTL_REG	0xa0
> > > +#define TIMER_CNT64_CTL_CLR		BIT(0)
> > > +#define TIMER_CNT64_CTL_RL		BIT(1)
> > > +#define TIMER_CNT64_LOW_REG	0xa4
> > > +#define TIMER_CNT64_HIGH_REG	0xa8
> > >  
> > >  static void __iomem *timer_base;
> > >  
> > > @@ -96,6 +103,20 @@ static struct irqaction sun4i_timer_irq = {
> > >  	.dev_id = &sun4i_clockevent,
> > >  };
> > >  
> > > +static u32 sun4i_timer_sched_read(void)
> > > +{
> > > +	u32 reg = readl(timer_base + TIMER_CNT64_CTL_REG);
> > 
> > If we can be absolutely sure that nothing else may ever change
> > the TIMER_CNT64_CTL_REG, then its default value can be probably
> > cached instead of doing expensive read from the hardware register
> > each time?
> 
> Since it's a free-running counter, its value will always change, so the
> caching will bring no additions at all, right?

Sorry, 'caching' was not a very good description for something that is
already a compile time constant. I mean just replace

    u32 reg = readl(timer_base + TIMER_CNT64_CTL_REG);

with 

    u32 reg = TIMER_CNT64_CTL_CLR;

Because we know that the TIMER_CNT64_CTL_REG is already supposed
to have the default TIMER_CNT64_CTL_CLR value (initialized in the
'sun4i_timer_init' function) between calls to 'sun4i_timer_sched_read'.
Inside of 'sun4i_timer_sched_read' we set an extra TIMER_CNT64_CTL_RL
bit in this register, but wait until it clears, effectively reverting
TIMER_CNT64_CTL_REG register back to the default TIMER_CNT64_CTL_CLR
value.

Removing this extra HW register read can save roughly a hundred of CPU
cycles here and provide a ~10% overall improvement for gettimeofday
(these estimates are based on the earlier benchmarks done with the
Allwinner 3.4 kernel).

Or maybe I'm overlooking something?

-- 
Best regards,
Siarhei Siamashka