From: simon.guinot@sequanux•org (Simon Guinot)
To: linux-arm-kernel@lists•infradead.org
Subject: [PATCHv2 7/9] ARM: kirkwood: convert LaCie Net{2, 5}Big v2 platforms to DT
Date: Fri, 2 Aug 2013 23:25:53 +0200 [thread overview]
Message-ID: <20130802212553.GA20330@kw.sim.vm.gnt> (raw)
In-Reply-To: <1375369655-1310-8-git-send-email-thomas.petazzoni@free-electrons.com>
On Thu, Aug 01, 2013 at 05:07:33PM +0200, Thomas Petazzoni wrote:
> This commit converts the LaCie Net2big and Net5Big Kirkwood boards to
> use a Device Tree representation. All devices are converted to use a
> DT representation, except the GPIO extension leds that use a special
> leds-netxbig driver that does not yet have a DT binding.
>
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons•com>
> ---
> arch/arm/boot/dts/Makefile | 2 +
> arch/arm/boot/dts/kirkwood-net2big-v2.dts | 219 ++++++++++++++++
> arch/arm/boot/dts/kirkwood-net5big-v2.dts | 265 +++++++++++++++++++
> arch/arm/mach-kirkwood/Kconfig | 26 +-
> arch/arm/mach-kirkwood/Makefile | 4 +-
> arch/arm/mach-kirkwood/board-dt.c | 4 +
> arch/arm/mach-kirkwood/board-netxbig_v2.c | 199 ++++++++++++++
> arch/arm/mach-kirkwood/common.h | 6 +
> arch/arm/mach-kirkwood/netxbig_v2-setup.c | 422 ------------------------------
> 9 files changed, 709 insertions(+), 438 deletions(-)
> create mode 100644 arch/arm/boot/dts/kirkwood-net2big-v2.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-net5big-v2.dts
> create mode 100644 arch/arm/mach-kirkwood/board-netxbig_v2.c
> delete mode 100644 arch/arm/mach-kirkwood/netxbig_v2-setup.c
Again, thanks for this patch. Please, see my comments below.
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index d168bed..20a6886 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -85,6 +85,8 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
> kirkwood-lsxhl.dtb \
> kirkwood-mplcec4.dtb \
> kirkwood-mv88f6281gtw-ge.dtb \
> + kirkwood-net2big-v2.dtb \
> + kirkwood-net5big-v2.dtb \
> kirkwood-netgear_readynas_duo_v2.dtb \
> kirkwood-ns2.dtb \
> kirkwood-ns2lite.dtb \
> diff --git a/arch/arm/boot/dts/kirkwood-net2big-v2.dts b/arch/arm/boot/dts/kirkwood-net2big-v2.dts
> new file mode 100644
> index 0000000..608ef01
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-net2big-v2.dts
> @@ -0,0 +1,219 @@
> +/*
> + * LaCie 2Big Network v2
> + *
> + * Simon Guinot <sguinot@lacie•com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +/include/ "kirkwood.dtsi"
> +/include/ "kirkwood-6281.dtsi"
> +
> +/ {
> + model = "LaCie 2Big Network v2";
> + compatible = "lacie,net2big-v2", "marvell,kirkwood-88f6281", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x20000000>; /* 512 MB */
The memory size is 256MB (0x10000000).
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8 earlyprintk";
> + };
> +
> + ocp at f1000000 {
> + pinctrl at 10000 {
> + pinctrl-0 = <&pmx_misc &pmx_sysrst>;
> + pinctrl-names = "default";
> +
> + pmx_keys: pmx-keys {
> + marvell,pins = "mpp13", "mpp15", "mpp34";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sata_power: pmx-sata-power {
> + marvell,pins = "mpp16", "mpp17";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sata1: pmx-sata1 {
> + marvell,pins = "mpp20";
> + marvell,function = "sata1";
> + };
> +
> + pmx_sata0: pmx-sata0 {
> + marvell,pins = "mpp21";
> + marvell,function = "sata0";
> + };
> +
> + pmx_poweroff: pmx-poweroff {
> + marvell,pins = "mpp7";
> + marvell,function = "gpo";
> + };
> +
> + pmx_sysrst: pmx-sysrst {
> + marvell,pins = "mpp6";
> + marvell,function = "sysrst";
> + };
> +
> + /*
> + * MPP14: USB fuse alarm
> + * MPP24: USB mode select
> + * MPP26: USB device vbus
> + * MPP28: USB enable host vbus
> + * MPP35: inhibit switch power-off
> + * MPP36: SATA HDD1 presence
> + * MPP37: SATA HDD2 presence
> + * MPP40: eSATA presence
> + * MPP44: GPIO extension (data 0)
> + * MPP45: GPIO extension (data 1)
> + * MPP46: GPIO extension (data 2)
> + * MPP47: GPIO extension (addr 0)
> + * MPP48: GPIO extension (addr 1)
> + * MPP49: GPIO extension (addr 2)
> + */
> + pmx_misc: pmx-misc {
> + marvell,pins = "mpp14", "mpp24", "mpp26", "mpp28", "mpp29",
> + "mpp35", "mpp36", "mpp37", "mpp40", "mpp44",
> + "mpp45", "mpp46", "mpp47", "mpp48", "mpp49";
> + marvell,function = "gpio";
> + };
> + };
> +
> + spi at 10600 {
> + status = "okay";
> + pinctrl-0 = <&pmx_spi>;
> + pinctrl-names = "default";
> +
> + flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "mx25l4005a";
> + reg = <0>;
> + spi-max-frequency = <20000000>;
> + mode = <0>;
> +
> + partition at 0 {
> + reg = <0x0 0x80000>;
> + label = "u-boot";
> + };
> + };
> + };
> +
> + i2c at 11000 {
> + status = "okay";
> + pinctrl-0 = <&pmx_twsi0>;
> + pinctrl-names = "default";
> +
> + eeprom at 50 {
> + compatible = "at,24c04";
> + pagesize = <16>;
> + reg = <0x50>;
> + };
> + };
> +
> + serial at 12000 {
> + pinctrl-0 = <&pmx_uart0>;
> + pinctrl-names = "default";
> + clock-frequency = <200000000>;
The serial clock-frequency is 166666667 for the net2big_v2 as well as
the TCLK frequency. It could smart to inherit the clock frequencies (if
not given) from the TCLK.
> + status = "ok";
> + };
> +
> + ehci at 50000 {
> + status = "okay";
> + };
> +
> + sata at 80000 {
> + pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
> + pinctrl-names = "default";
> + status = "okay";
> + nr-ports = <2>;
> + };
> + };
> +
> + gpio_poweroff {
> + compatible = "gpio-poweroff";
> + pinctrl-0 = <&pmx_poweroff>;
> + pinctrl-names = "default";
> + gpios = <&gpio0 7 0>;
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_keys>;
> + pinctrl-names = "default";
> +
> + button at 1 {
> + label = "Back power switch (on|auto)";
> + linux,code = <0x1>;
> + linux,input-type = <5>; /* EV_SW */
> + gpios = <&gpio0 13 1>;
> + };
> + button at 2 {
> + label = "Back power switch (auto|off)";
> + linux,code = <0x2>;
> + linux,input-type = <5>; /* EV_SW */
> + gpios = <&gpio0 15 1>;
> + };
> + button at 3 {
> + label = "Function button";
> + linux,code = <0x165>; /* KEY_OPTION */
> + gpios = <&gpio1 3 1>;
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + pinctrl-0 = <&pmx_sata_power>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + sata0_power: regulator at 1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "SATA0 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 16 0>;
> + };
> +
> + sata1_power: regulator at 2 {
> + compatible = "regulator-fixed";
> + reg = <1>;
The regulator driver fails to register an already registred sysfs entry.
If I set "reg = <2>;" then the error goes away.
> + regulator-name = "SATA1 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 17 0>;
As for the d2net_v2, it would be nice to allow to enable/disable power
for the SATA disks.
> + };
> + };
> +};
> +
> +&mdio {
> + status = "okay";
> +
> + ethphy0: ethernet-phy at 0 {
> + device_type = "ethernet-phy";
> + reg = <8>;
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> + ethernet0-port at 0 {
> + phy-handle = <ðphy0>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/kirkwood-net5big-v2.dts b/arch/arm/boot/dts/kirkwood-net5big-v2.dts
> new file mode 100644
> index 0000000..46ca107
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-net5big-v2.dts
> @@ -0,0 +1,265 @@
> +/*
> + * LaCie 5Big Network v2
> + *
> + * Simon Guinot <sguinot@lacie•com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +/include/ "kirkwood.dtsi"
> +/include/ "kirkwood-6281.dtsi"
> +
> +/ {
> + model = "LaCie 5Big Network v2";
> + compatible = "lacie,net5big-v2", "marvell,kirkwood-88f6281", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x20000000>; /* 512 MB */
This time, the memory size is OK :)
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8 earlyprintk";
> + };
> +
> + ocp at f1000000 {
> + pinctrl at 10000 {
> + pinctrl-0 = <&pmx_misc &pmx_sysrst>;
> + pinctrl-names = "default";
> +
> + pmx_keys: pmx-keys {
> + marvell,pins = "mpp13", "mpp15", "mpp34";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sata_power: pmx-sata-power {
> + marvell,pins = "mpp16", "mpp17", "mpp41", "mpp42", "mpp43";
> + marvell,function = "gpio";
> + };
> +
> + pmx_poweroff: pmx-poweroff {
> + marvell,pins = "mpp7";
> + marvell,function = "gpo";
> + };
> +
> + pmx_sysrst: pmx-sysrst {
> + marvell,pins = "mpp6";
> + marvell,function = "sysrst";
> + };
> +
> + /*
> + * MPP14: USB fuse alarm
> + * MPP28: USB enable host vbus
> + * MPP29: GPIO extension ALE
> + * MPP35: inhibit switch power-off
> + * MPP36: SATA HDD1 presence
> + * MPP37: SATA HDD2 presence
> + * MPP38: SATA HDD3 presence
> + * MPP39: SATA HDD4 presence
> + * MPP40: SATA HDD5 presence
> + * MPP44: GPIO extension (data 0)
> + * MPP45: GPIO extension (data 1)
> + * MPP46: GPIO extension (data 2)
> + * MPP47: GPIO extension (addr 0)
> + * MPP48: GPIO extension (addr 1)
> + * MPP49: GPIO extension (addr 2)
> + */
> + pmx_misc: pmx-misc {
> + marvell,pins = "mpp14", "mpp28", "mpp29", "mpp35", "mpp36",
> + "mpp37", "mpp38", "mpp39", "mpp40", "mpp44",
> + "mpp45", "mpp46", "mpp47", "mpp48", "mpp49";
> + marvell,function = "gpio";
> + };
> +
> + pmx_ge1: pmx-ge1 {
> + marvell,pins = "mpp20", "mpp21", "mpp22", "mpp23", "mpp24",
> + "mpp25", "mpp26", "mpp27", "mpp30", "mpp31",
> + "mpp32", "mpp33";
> + marvell,function = "ge1";
> + };
> + };
> +
> + spi at 10600 {
> + status = "okay";
> + pinctrl-0 = <&pmx_spi>;
> + pinctrl-names = "default";
> +
> + flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "mx25l4005a";
> + reg = <0>;
> + spi-max-frequency = <20000000>;
> + mode = <0>;
> +
> + partition at 0 {
> + reg = <0x0 0x80000>;
> + label = "u-boot";
> + };
> + };
> + };
> +
> + i2c at 11000 {
> + status = "okay";
> + pinctrl-0 = <&pmx_twsi0>;
> + pinctrl-names = "default";
> +
> + eeprom at 50 {
> + compatible = "at,24c04";
> + pagesize = <16>;
> + reg = <0x50>;
> + };
> + };
> +
> + serial at 12000 {
> + pinctrl-0 = <&pmx_uart0>;
> + pinctrl-names = "default";
> + clock-frequency = <200000000>;
clock-frequency = <166666667>;
> + status = "ok";
> + };
> +
> + ehci at 50000 {
> + status = "okay";
> + };
> +
> + sata at 80000 {
> + pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
> + pinctrl-names = "default";
> + status = "okay";
> + nr-ports = <2>;
> + };
> + };
> +
> + gpio_poweroff {
> + compatible = "gpio-poweroff";
> + pinctrl-0 = <&pmx_poweroff>;
> + pinctrl-names = "default";
> + gpios = <&gpio0 7 0>;
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_keys>;
> + pinctrl-names = "default";
> +
> + button at 1 {
> + label = "Back power switch (on|auto)";
> + linux,code = <0x1>;
> + linux,input-type = <5>; /* EV_SW */
> + gpios = <&gpio0 13 1>;
> + };
> + button at 2 {
> + label = "Back power switch (auto|off)";
> + linux,code = <0x2>;
> + linux,input-type = <5>; /* EV_SW */
> + gpios = <&gpio0 15 1>;
> + };
> + button at 3 {
> + label = "Function button";
> + linux,code = <0x165>; /* KEY_OPTION */
> + gpios = <&gpio1 3 1>;
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + pinctrl-0 = <&pmx_sata_power>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + sata0_power: regulator at 1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "SATA0 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 16 0>;
> + };
> +
> + sata1_power: regulator at 2 {
> + compatible = "regulator-fixed";
> + reg = <1>;
reg = <2>; ?
> + regulator-name = "SATA1 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 17 0>;
> + };
> +
> + sata2_power: regulator at 3 {
> + compatible = "regulator-fixed";
> + reg = <1>;
reg = <3>; ?
> + regulator-name = "SATA2 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio1 9 0>;
> + };
> +
> + sata3_power: regulator at 4 {
> + compatible = "regulator-fixed";
> + reg = <1>;
reg = <4>; ?
> + regulator-name = "SATA3 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio1 10 0>;
> + };
> +
> + sata4_power: regulator at 5 {
> + compatible = "regulator-fixed";
> + reg = <1>;
reg = <5>; ?
> + regulator-name = "SATA4 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio1 11 0>;
> + };
> + };
> +};
> +
> +&mdio {
> + status = "okay";
> +
> + ethphy0: ethernet-phy at 0 {
> + device_type = "ethernet-phy";
> + reg = <8>;
> + };
> +
> + ethphy1: ethernet-phy at 1 {
> + device_type = "ethernet-phy";
> + reg = <0>;
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> + ethernet0-port at 0 {
> + phy-handle = <ðphy0>;
> + };
> +};
> +
> +ð1 {
> + status = "okay";
> + ethernet1-port at 0 {
> + phy-handle = <ðphy1>;
> + };
eth1 don't work and I don't know why. I can only say it works with the
legacy board-setup and Linux v3.10.
> +};
> diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
> index f624162..b7e66fa 100644
> --- a/arch/arm/mach-kirkwood/Kconfig
> +++ b/arch/arm/mach-kirkwood/Kconfig
> @@ -5,20 +5,6 @@ menu "Marvell Kirkwood Implementations"
> config KIRKWOOD_LEGACY
> bool
>
> -config MACH_NET2BIG_V2
> - bool "LaCie 2Big Network v2 NAS Board"
> - select KIRKWOOD_LEGACY
> - help
> - Say 'Y' here if you want your kernel to support the
> - LaCie 2Big Network v2 NAS.
> -
> -config MACH_NET5BIG_V2
> - bool "LaCie 5Big Network v2 NAS Board"
> - select KIRKWOOD_LEGACY
> - help
> - Say 'Y' here if you want your kernel to support the
> - LaCie 5Big Network v2 NAS.
> -
> config MACH_OPENRD
> select KIRKWOOD_LEGACY
> bool
> @@ -113,6 +99,18 @@ config MACH_MV88F6281GTW_GE_DT
> Say 'Y' here if you want your kernel to support the
> Marvell 88F6281 GTW GE Board (Flattened Device Tree).
>
> +config MACH_NET2BIG_V2_DT
> + bool "LaCie 2Big Network v2 NAS Board (Flattened Device Tree)"
> + help
> + Say 'Y' here if you want your kernel to support the
> + LaCie 2Big Network v2 NAS (Flattened Device Tree).
> +
> +config MACH_NET5BIG_V2_DT
> + bool "LaCie 5Big Network v2 NAS Board (Flattened Device Tree)"
> + help
> + Say 'Y' here if you want your kernel to support the
> + LaCie 5Big Network v2 NAS (Flattened Device Tree).
> +
Before changing this options, we need to fix the Kconfig dependencies
for the driver led-netxbig. I will send a patch.
> endmenu
>
> endif
> diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
> index 0dcc5d4..38d0d74 100644
> --- a/arch/arm/mach-kirkwood/Makefile
> +++ b/arch/arm/mach-kirkwood/Makefile
> @@ -1,8 +1,6 @@
> obj-y += common.o pcie.o
> obj-$(CONFIG_KIRKWOOD_LEGACY) += irq.o mpp.o
>
> -obj-$(CONFIG_MACH_NET2BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o
> -obj-$(CONFIG_MACH_NET5BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o
> obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o
> obj-$(CONFIG_MACH_RD88F6192_NAS) += rd88f6192-nas-setup.o
> obj-$(CONFIG_MACH_RD88F6281) += rd88f6281-setup.o
> @@ -13,3 +11,5 @@ obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o
> obj-$(CONFIG_ARCH_KIRKWOOD_DT) += board-dt.o
> obj-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += board-dnskw.o
> obj-$(CONFIG_MACH_MV88F6281GTW_GE_DT) += board-mv88f6281gtw_ge.o
> +obj-$(CONFIG_MACH_NET2BIG_V2) += board-netxbig_v2.o
CONFIG_MACH_NET2BIG_V2_DT
> +obj-$(CONFIG_MACH_NET5BIG_V2) += board-netxbig_v2.o
CONFIG_MACH_NET5BIG_V2_DT
> diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
> index b129c65..80955cc 100644
> --- a/arch/arm/mach-kirkwood/board-dt.c
> +++ b/arch/arm/mach-kirkwood/board-dt.c
... snip ...
> diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
> index cc639bb..a9010a3 100644
> --- a/arch/arm/mach-kirkwood/common.h
> +++ b/arch/arm/mach-kirkwood/common.h
> @@ -71,6 +71,12 @@ void mv88f6281gtw_ge_init(void);
> static inline void mv88f6281gtw_ge_init(void) {};
> #endif
>
> +#if defined(MACH_NET2BIG_V2_DT) || defined(MACH_NET5BIG_V2_DT)
#if defined(CONFIG_MACH_NET2BIG_V2_DT) || defined(CONFIG_MACH_NET5BIG_V2_DT)
Thanks,
Simon
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 198 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20130802/ea5796f2/attachment.sig>
next prev parent reply other threads:[~2013-08-02 21:25 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-08-01 15:07 [PATCHv2 0/9] ARM: kirkwood: convert a few more boards to DT Thomas Petazzoni
2013-08-01 15:07 ` [PATCHv2 1/9] ARM: kirkwood: convert d2net_v2 " Thomas Petazzoni
2013-08-02 14:31 ` Simon Guinot
2013-10-12 15:26 ` Thomas Petazzoni
2013-08-02 14:46 ` [PATCH] leds: leds-ns2: depends on ARCH_KIRKWOOD Simon Guinot
2013-08-03 18:16 ` Jason Cooper
2013-08-05 22:50 ` Bryan Wu
2013-08-13 9:58 ` [PATCHv2 1/9] ARM: kirkwood: convert d2net_v2 to DT Mark Rutland
2013-10-12 15:29 ` Thomas Petazzoni
2013-10-14 11:26 ` Mark Rutland
2013-08-01 15:07 ` [PATCHv2 2/9] ARM: kirkwood: remove support for legacy booting of Dockstar Thomas Petazzoni
2013-08-03 18:27 ` Jason Cooper
2013-08-01 15:07 ` [PATCHv2 3/9] ARM: kirkwood: remove support for legacy booting of Guruplug Thomas Petazzoni
2013-08-02 12:49 ` Jason Cooper
2013-08-02 13:08 ` Arnaud Patard (Rtp)
2013-08-01 15:07 ` [PATCHv2 4/9] ARM: kirkwood: remove support for legacy booting of Sheevaplug Thomas Petazzoni
2013-08-01 15:07 ` [PATCHv2 5/9] ARM: kirkwood: remove LaCie boards that are supported through DT Thomas Petazzoni
2013-08-01 15:07 ` [PATCHv2 6/9] ARM: kirkwood: convert the mv88f6281gtw_ge board to DT Thomas Petazzoni
2013-08-01 15:07 ` [PATCHv2 7/9] ARM: kirkwood: convert LaCie Net{2, 5}Big v2 platforms " Thomas Petazzoni
2013-08-02 21:25 ` Simon Guinot [this message]
2013-08-03 17:12 ` Jason Cooper
2013-08-02 21:34 ` [PATCH] leds: leds-netxbig: depends on ARCH_KIRKWOOD Simon Guinot
2013-08-03 14:12 ` Jason Cooper
2013-08-05 22:52 ` Bryan Wu
2013-08-06 12:17 ` Jason Cooper
2013-08-06 17:40 ` Bryan Wu
2013-08-01 15:07 ` [PATCHv2 8/9] ARM: kirkwood: remove unused common code for LaCie platforms Thomas Petazzoni
2013-08-02 21:45 ` Simon Guinot
2013-08-01 15:07 ` [PATCHv2 9/9] ARM: kirkwood: update defconfig after DT conversions Thomas Petazzoni
2013-08-03 18:56 ` [PATCHv2 0/9] ARM: kirkwood: convert a few more boards to DT Jason Cooper
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20130802212553.GA20330@kw.sim.vm.gnt \
--to=simon.guinot@sequanux$(echo .)org \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox