Subject: [PATCH 00/11] ARM: OMAP2+: CM cleanup series

From: [email-masked] (Tony Lindgren)
Date: Fri, 11 Oct 2013 17:09:42 -0700

* Tero Kristo <[email-masked]> [131011 09:24]:
> 
> If someone could verify the omap2 changes, that would be nice.

Seems to boot on my n800 just fine, dmesg below.

Tony

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.12.0-rc4-00050-gf44928c (tmlind at muffinssi) (gcc version 4.3.5 (Debian 4.3.5-4) ) #245 Fri Oct 11 17:03:03 PDT 2013
[    0.000000] CPU: ARMv6-compatible processor [4107b362] revision 2 (ARMv6TEJ), cr=00c5387d
[    0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Nokia N800
[    0.000000] Ignoring unrecognised tag 0x414f4d50
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat c075891c, node_mem_map c0cb9000
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] OMAP2420
[    0.000000] 
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: root=/dev/mmcblk0p2 rootwait console=ttyO2,115200 earlyprintk ignore_loglevel
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 116864K/131072K available (5069K kernel code, 344K rwdata, 1812K rodata, 271K init, 5489K bss, 14208K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06c06d0   (6882 kB)
[    0.000000]       .init : 0xc06c1000 - 0xc0704ddc   ( 272 kB)
[    0.000000]       .data : 0xc0706000 - 0xc075c200   ( 345 kB)
[    0.000000]        .bss : 0xc075c200 - 0xc0cb8808   (5490 kB)
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 2.0) with 96 interrupts
[    0.000000] Total of 96 interrupts on 1 active controller
[    0.000000] Clocking rate (Crystal/DPLL/MPU): 19.2/658/329 MHz
[    0.000000] OMAP clockevent source: timer1 at 32768 Hz
[    0.000000] omap2_sync32k_clocksource_init: failed to get counter_32k resource
[    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[    0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present.
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.000000] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.000000] ... MAX_LOCK_DEPTH:          48
[    0.000000] ... MAX_LOCKDEP_KEYS:        8191
[    0.000000] ... CLASSHASH_SIZE:          4096
[    0.000000] ... MAX_LOCKDEP_ENTRIES:     16384
[    0.000000] ... MAX_LOCKDEP_CHAINS:      32768
[    0.000000] ... CHAINHASH_SIZE:          16384
[    0.000000]  memory used by lock dependency info: 3695 kB
[    0.000000]  per task-struct memory footprint: 1152 bytes
[    0.070000] Calibrating delay loop... 217.49 BogoMIPS (lpj=1087488)
[    0.150000] pid_max: default: 32768 minimum: 301
[    0.150000] Security Framework initialized
[    0.160000] Mount-cache hash table entries: 512
[    0.170000] CPU: Testing write buffer coherency: ok
[    0.180000] Setting up static identity map for 0xc04d3518 - 0xc04d3588
[    0.210000] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2
[    0.260000] pinctrl core: initialized pinctrl subsystem
[    0.280000] regulator-dummy: no parameters
[    0.290000] NET: Registered protocol family 16
[    0.300000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.310000] omap-gpmc omap-gpmc: GPMC revision 2.0
[    0.340000] omap_gpio omap_gpio.0: Could not get gpio dbck
[    0.350000] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.360000] OMAP GPIO hardware version 1.8
[    0.360000] omap_gpio omap_gpio.1: Could not get gpio dbck
[    0.370000] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.380000] omap_gpio omap_gpio.2: Could not get gpio dbck
[    0.390000] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.400000] omap_gpio omap_gpio.3: Could not get gpio dbck
[    0.410000] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.440000] omap_mux_init: Add partition: #1: core, flags: b
[    0.510000]  mmci-omap.0: alias fck already exists
[    0.530000] TUSB 6010
[    0.530000] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[    0.540000] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.590000] OMAP DMA hardware revision 2.0
[    0.600000] Missing cpus node, bailing out
[    0.830000] bio: create slab <bio-0> at 0
[    1.100000] omap-dma-engine omap-dma-engine: OMAP DMA engine driver
[    1.120000] SCSI subsystem initialized
[    1.130000] usbcore: registered new interface driver usbfs
[    1.140000] usbcore: registered new interface driver hub
[    1.150000] usbcore: registered new device driver usb
[    1.170000] omap_i2c omap_i2c.1: bus 1 rev3.3 at 400 kHz
[    1.180000] omap_i2c omap_i2c.2: bus 2 rev3.3 at 400 kHz
[    1.560000] NET: Registered protocol family 2
[    1.570000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    1.580000] TCP bind hash table entries: 1024 (order: 3, 36864 bytes)
[    1.590000] TCP: Hash tables configured (established 1024 bind 1024)
[    1.600000] TCP: reno registered
[    1.600000] UDP hash table entries: 256 (order: 2, 20480 bytes)
[    1.610000] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[    1.620000] NET: Registered protocol family 1
[    1.630000] RPC: Registered named UNIX socket transport module.
[    1.630000] RPC: Registered udp transport module.
[    1.640000] RPC: Registered tcp transport module.
[    1.640000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.660000] NetWinder Floating Point Emulator V0.97 (double precision)
[    1.660000] CPU PMU: probing PMU on CPU 0
[    1.670000] hw perfevents: enabled with v6 PMU driver, 3 counters available
[    2.230000] VFS: Disk quotas dquot_6.5.2
[    2.230000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.250000] NFS: Registering the id_resolver key type
[    2.250000] Key type id_resolver registered
[    2.260000] Key type id_legacy registered
[    2.260000] jffs2: version 2.2. (NAND) (SUMMARY)  ? 2001-2006 Red Hat, Inc.
[    2.270000] msgmni has been set to 228
[    2.290000] io scheduler noop registered
[    2.290000] io scheduler deadline registered
[    2.300000] io scheduler cfq registered (default)
[    2.310000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.340000] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[    2.360000] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[    2.370000] omap_uart.2: ttyO2 at MMIO 0x4806e000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[    2.380000] console [ttyO2] enabled, bootconsole disabled
[    2.380000] console [ttyO2] enabled, bootconsole disabled
[    2.400000] omap_rng omap_rng: OMAP Random Number Generator ver. 40
[    2.500000] brd: module loaded
[    2.550000] loop: module loaded
[    2.560000] Menelaus rev 2.2
[    2.600000] mtdoops: mtd device (mtddev=name/number) must be supplied
[    2.610000] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x04000000, virtual base c88c0000, freq 54 MHz
[    2.620000] OneNAND Manufacturer: Samsung (0xec)
[    2.620000] Muxed OneNAND(DDP) 256MB 1.8V 16-bit (0x48)
[    2.630000] OneNAND version = 0x0011
[    2.630000] Chip support all block unlock
[    2.640000] onenand_wait: controller error! state 15 ctrl 0x0400 intr 0x8000
[    2.650000] Scanning device for bad blocks
[    2.910000] Creating 5 MTD partitions on "omap2-onenand":
[    2.920000] 0x000000000000-0x000000020000 : "bootloader"
[    2.940000] 0x000000020000-0x000000080000 : "config"
[    2.960000] 0x000000080000-0x000000280000 : "kernel"
[    2.970000] 0x000000280000-0x000000680000 : "initfs"
[    2.990000] 0x000000680000-0x000010000000 : "rootfs"
[    3.040000] omap-dma-engine omap-dma-engine: allocating channel for 44
[    3.050000] omap-dma-engine omap-dma-engine: allocating channel for 43
[    3.080000] usbcore: registered new interface driver asix
[    3.090000] usbcore: registered new interface driver ax88179_178a
[    3.100000] usbcore: registered new interface driver cdc_ether
[    3.100000] usbcore: registered new interface driver r815x
[    3.110000] usbcore: registered new interface driver smsc95xx
[    3.120000] usbcore: registered new interface driver net1080
[    3.130000] usbcore: registered new interface driver cdc_subset
[    3.140000] usbcore: registered new interface driver zaurus
[    3.140000] usbcore: registered new interface driver cdc_ncm
[    3.150000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.160000] ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
[    3.170000] ehci-omap: OMAP-EHCI Host Controller driver
[    3.180000] usbcore: registered new interface driver cdc_wdm
[    3.180000] usbcore: registered new interface driver usb-storage
[    3.190000] usbcore: registered new interface driver usbtest
[    3.230000] tusb: prcm2.0 int2.0 gpio3.0 dma3.0 dieid2 rev3.1
[    3.230000] drivers/usb/musb/tusb6010.c tusb_musb_disable: dma still active
[    3.240000] musb-hdrc: ConfigData=0x06 (UTMI-8, dyn FIFOs, SoftConn)
[    3.250000] musb-hdrc: MHDRC RTL version 1.400 
[    3.250000] musb-hdrc: setup fifo_mode 4
[    3.260000] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    3.260000] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver
[    3.280000] musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 1
[    3.280000] musb-hdrc musb-hdrc.0.auto: supports USB remote wakeup
[    3.300000] usb usb1: default language 0x0409
[    3.300000] usb usb1: udev 1, busnum 1, minor = 0
[    3.310000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.310000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.320000] usb usb1: Product: MUSB HDRC host driver
[    3.330000] usb usb1: Manufacturer: Linux 3.12.0-rc4-00050-gf44928c musb-hcd
[    3.330000] usb usb1: SerialNumber: musb-hdrc.0.auto
[    3.350000] usb usb1: usb_probe_device
[    3.350000] usb usb1: configuration #1 chosen from 1 choice
[    3.360000] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    3.370000] hub 1-0:1.0: usb_probe_interface
[    3.370000] hub 1-0:1.0: usb_probe_interface - got id
[    3.380000] hub 1-0:1.0: USB hub found
[    3.380000] hub 1-0:1.0: 1 port detected
[    3.390000] hub 1-0:1.0: standalone hub
[    3.390000] hub 1-0:1.0: individual port power switching
[    3.400000] hub 1-0:1.0: no over-current protection
[    3.400000] hub 1-0:1.0: Single TT
[    3.410000] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[    3.410000] hub 1-0:1.0: power on to power good time: 10ms
[    3.420000] hub 1-0:1.0: 200mA bus power budget for each child
[    3.430000] hub 1-0:1.0: local power source is good
[    3.440000] hub 1-0:1.0: enabling power on all ports
[    3.440000] drivers/usb/musb/tusb6010.c tusb_musb_enable: dma not reactivated
[    3.470000] udc musb-hdrc.0.auto: registering UDC driver [g_ether]
[    3.480000] using random self ethernet address
[    3.480000] using random host ethernet address
[    3.490000] usb0: HOST MAC b2:a6:82:3d:61:d2
[    3.500000] usb0: MAC ba:a4:f3:92:f4:6a
[    3.500000] using random self ethernet address
[    3.510000] using random host ethernet address
[    3.510000] g_ether gadget: adding config #2 'RNDIS'/c074c92c
[    3.520000] rndis_register: configNr = 0
[    3.520000] g_ether gadget: adding 'rndis'/c7b379c0 to config 'RNDIS'/c074c92c
[    3.530000] rndis_set_param_medium: 0 0
[    3.540000] g_ether gadget: RNDIS: dual speed IN/ep1in OUT/ep1out NOTIFY/ep2in
[    3.540000] g_ether gadget: cfg 2/c074c92c speeds: high full
[    3.550000] g_ether gadget:   interface 0 = rndis/c7b379c0
[    3.560000] g_ether gadget:   interface 1 = rndis/c7b379c0
[    3.560000] g_ether gadget: adding config #1 'CDC Ethernet (EEM)'/c074c8b8
[    3.570000] g_ether gadget: adding 'cdc_eem'/c7b37900 to config 'CDC Ethernet (EEM)'/c074c8b8
[    3.580000] g_ether gadget: CDC Ethernet (EEM): dual speed IN/ep1in OUT/ep1out
[    3.590000] g_ether gadget: cfg 1/c074c8b8 speeds: high full
[    3.590000] g_ether gadget:   interface 0 = cdc_eem/c7b37900
[    3.600000] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[    3.610000] g_ether gadget: g_ether ready
[    3.620000] mousedev: PS/2 mouse device common for all mice
[    3.640000] i2c /dev entries driver
[    3.670000] retu-mfd 3-0001: Retu & Vilma v1.5 found
[    3.690000] input: retu-pwrbutton as /devices/platform/i2c-cbus-gpio.3/i2c-3/3-0001/retu-pwrbutton/input/input0
[    3.710000] Driver for 1-wire Dallas network protocol.
[    3.720000] omap_wdt: OMAP Watchdog Timer Rev 0x11: initial timeout 60 sec
[    3.740000] omap-dma-engine omap-dma-engine: allocating channel for 61
[    3.750000] omap-dma-engine omap-dma-engine: allocating channel for 62
[    3.760000] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
[    3.770000] hub 1-0:1.0: hub_suspend
[    3.770000] usb usb1: bus auto-suspend, wakeup 1
[    3.890000] mmci-omap mmci-omap.0: command timeout (CMD52)
[    3.900000] mmci-omap mmci-omap.0: command timeout (CMD52)
[    3.930000] mmci-omap mmci-omap.0: command timeout (CMD5)
[    3.930000] mmci-omap mmci-omap.0: command timeout (CMD5)
[    3.940000] mmci-omap mmci-omap.0: command timeout (CMD5)
[    3.950000] mmci-omap mmci-omap.0: command timeout (CMD5)
[    3.970000] usbcore: registered new interface driver usbhid
[    3.980000] usbhid: USB HID core driver
[    3.990000] oprofile: using arm/armv6
[    3.990000] TCP: cubic registered
[    4.000000] Initializing XFRM netlink socket
[    4.000000] NET: Registered protocol family 17
[    4.010000] NET: Registered protocol family 15
[    4.010000] Key type dns_resolver registered
[    4.030000] mux: Failed to setup hwmod io irq -22
[    4.040000] Power Management for OMAP2 initializing
[    4.050000] PRCM revision 1.0
[    4.070000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    4.090000] Waiting for root device /dev/mmcblk0p2...
[    4.110000] mmc0: host does not support reading read-only switch. assuming write-enable.
[    4.120000] mmc0: new SDHC card at address ea4d
[    4.130000] mmcblk0: mmc0:ea4d SU04G 3.79 GiB 
[    4.150000]  mmcblk0: p1 p2
[    4.160000] mmci-omap mmci-omap.0: command timeout (CMD52)
[    4.170000] mmci-omap mmci-omap.0: command timeout (CMD52)
[    4.180000] mmci-omap mmci-omap.0: command timeout (CMD8)
[    4.190000] mmci-omap mmci-omap.0: command timeout (CMD5)
[    4.190000] mmci-omap mmci-omap.0: command timeout (CMD5)
[    4.210000] mmci-omap mmci-omap.0: command timeout (CMD5)
[    4.220000] mmci-omap mmci-omap.0: command timeout (CMD5)
[    4.230000] mmci-omap mmci-omap.0: command timeout (CMD8)
[    4.320000] mmc1: SD Status: Invalid Allocation Unit size.
[    4.330000] mmc1: host does not support reading read-only switch. assuming write-enable.
[    4.340000] mmc1: new SD card at address e624
[    4.370000] mmcblk1: mmc1:e624 SD128 120 MiB 
[    4.390000]  mmcblk1: p1
[    5.790000] kjournald starting.  Commit interval 5 seconds
[    5.800000] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended
[    5.960000] EXT3-fs (mmcblk0p2): using internal journal
[    5.970000] EXT3-fs (mmcblk0p2): recovery complete
[    5.980000] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[    5.990000] VFS: Mounted root (ext3 filesystem) on device 179:2.
[    6.000000] Freeing unused kernel memory: 268K (c06c1000 - c0704000)