Subject: [PATCH] ARM: dts: Gateworks GW5520 support (i.MX6)

From: [email-masked] (Shawn Guo)
Date: Mon, 18 Aug 2014 14:35:11 +0800

On Sat, Aug 09, 2014 at 01:23:22AM -0700, Tim Harvey wrote:
> +&iomuxc {

If you do not mind, I would ask you to put iomuxc node at the bottom of
the file.  Doing so makes the file a bit easier to read.

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_hog>;
> +
> +	imx6qdl-gw552x {
> +		pinctrl_hog: hoggrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_GPIO_9__GPIO1_IO09     0x80000000 /* USBHUB_RST# */
> +				MX6QDL_PAD_GPIO_17__GPIO7_IO12    0x80000000 /* PCIESKT_WDIS# */

Please use a proper pad configuration value instead of 0x80000000, which
will rely on the hardware reset state or what bootloader configures.

Also, can these two pins be moved to some pinctrl entries used by
particular client device?

> +			>;
> +		};
> +
> +		pinctrl_gpmi_nand: gpminandgrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
> +				MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
> +				MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
> +				MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
> +				MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
> +				MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
> +				MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
> +				MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
> +				MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
> +				MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
> +				MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
> +				MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
> +				MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
> +				MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
> +				MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
> +				MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
> +			>;
> +		};
> +
> +		pinctrl_i2c1: i2c1grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
> +				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
> +			>;
> +		};
> +
> +		pinctrl_i2c2: i2c2grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
> +				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
> +			>;
> +		};
> +
> +		pinctrl_i2c3: i2c3grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
> +				MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
> +			>;
> +		};
> +
> +		pinctrl_pcie: pciegrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_ENET_TXD1__GPIO1_IO29  0x80000000 /* PCIE_RST# */

Fix 0x80000000.

> +			>;
> +		};
> +
> +		pinctrl_uart2: uart2grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
> +				MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
> +			>;
> +		};
> +
> +		pinctrl_uart3: uart3grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
> +				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
> +			>;
> +		};
> +
> +		pinctrl_uart5: uart5grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x1b0b1
> +				MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x1b0b1
> +			>;
> +		};
> +	};
> +
> +        gpio_leds {

This node can just be saved by putting gpioledsgrp into imx6qdl-gw552x.
> +                pinctrl_gpio_leds: gpioledsgrp {
> +                        fsl,pins = <

Use tab for indentation.

> +				MX6QDL_PAD_KEY_COL0__GPIO4_IO06   0x80000000 /* user1 led */
> +				MX6QDL_PAD_KEY_ROW0__GPIO4_IO07   0x80000000 /* user2 led */
> +				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15   0x80000000 /* user3 led */

Fix 0x80000000.

Shawn

> +                        >;
> +                };
> +        };
> +
> +};
> +
> +&pcie {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pcie>;
> +	reset-gpio = <&gpio1 29 0>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	status = "okay";
> +};
> +
> +&uart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart3>;
> +	status = "okay";
> +};
> +
> +&uart5 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart5>;
> +	status = "okay";
> +};
> +
> +&usbh1 {
> +	status = "okay";
> +};
> -- 
> 1.8.3.2
>