Subject: [PATCH v2 1/1] add support for Seagate BlackArmor NAS220

From: [email-masked] (Evgeni Dobrev)
Date: Mon, 22 Dec 2014 09:04:45 +0100

This patch adds support for Seagate BlackArmor NAS220.

The Seagate BlackArmor NAS 220 is a NAS system based on Marvell 88f6192. It has
32MB NAND and 128MB DRAM. It has two SATA slots, one Gigabit Ethernet port, two
USB 2.0 ports, two buttons and three LEDs. There is a serial port available on
the CN5 connector on the board (1 - TX, 4 - RX, 6 - GND).

The only functionality still not implemented is the bi-color led on the front
panel (status). Pins mpp22 and mpp23 control this led. Setting mpp22 to high and
mpp23 to low results in orange color. Setting mpp22 to low and mpp23 to high
results in blue color.

The third led is wired to show the SATA activity on the two drives.

Signed-off-by: Evgeni Dobrev <[email-masked]>
---
 arch/arm/boot/dts/Makefile            |    1 +
 arch/arm/boot/dts/kirkwood-nas220.dts |  158 +++++++++++++++++++++++++++++++++
 2 files changed, 159 insertions(+)
 create mode 100644 arch/arm/boot/dts/kirkwood-nas220.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 38c89ca..8b9ad1d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -132,6 +132,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
 	kirkwood-lsxhl.dtb \
 	kirkwood-mplcec4.dtb \
 	kirkwood-mv88f6281gtw-ge.dtb \
+	kirkwood-nas220.dtb \
 	kirkwood-net2big.dtb \
 	kirkwood-net5big.dtb \
 	kirkwood-netgear_readynas_duo_v2.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-nas220.dts b/arch/arm/boot/dts/kirkwood-nas220.dts
new file mode 100644
index 0000000..43c9bbc
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-nas220.dts
@@ -0,0 +1,158 @@
+/*
+ * Device Tree file for Seagate BlackArmor NAS220
+ *
+ * Copyright (C) 2014 Evgeni Dobrev <[email-masked]>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+
+/ {
+	model = "Seagate NAS 220";
+	compatible = "seagate,nas220","marvell,kirkwood-88f6192","marvell,kirkwood";
+
+	memory { /* 128 MB */
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	ocp at f1000000 {
+		pinctrl: pin-controller at 10000 {
+			pinctrl-0 = <&pmx_uart0
+				     &pmx_button_reset
+				     &pmx_button_power>;
+			pinctrl-names = "default";
+
+			pmx_act_sata0: pmx-act-sata0 {
+				marvell,pins = "mpp15";
+				marvell,function = "sata0";
+			};
+			pmx_act_sata1: pmx-act-sata1 {
+				marvell,pins = "mpp16";
+				marvell,function = "sata1";
+			};
+			pmx_power_sata0: pmx-power-sata0 {
+				marvell,pins = "mpp24";
+				marvell,function = "gpio";
+			};
+			pmx_power_sata1: pmx-power-sata1 {
+				marvell,pins = "mpp28";
+				marvell,function = "gpio";
+			};
+			pmx_button_reset: pmx-button-reset {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+			pmx_button_power: pmx-button-power {
+				marvell,pins = "mpp26";
+				marvell,function = "gpio";
+			};
+		};
+
+		serial at 12000 {
+			status = "okay";
+		};
+
+		sata at 80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+
+		i2c at 11000 {
+			status = "okay";
+			adt7476: adt7476a at 2e {
+				compatible = "adi,adt7476";
+				reg = <0x2e>;
+			};
+		};
+	};
+
+	gpio_poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		button at 1{
+			label = "Reset push button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+		button at 2{
+			label = "Power push button";
+			linux,code = <KEY_SLEEP>;
+			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		blue-power {
+			label = "nas220:blue:power";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_power_sata0 &pmx_power_sata1>;
+		pinctrl-names = "default";
+
+		sata0_power: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "SATA0 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 24 0>;
+		};
+
+		sata1_power: regulator at 2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "SATA1 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 28 0>;
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+	ethphy0: ethernet-phy at 8 {
+		 reg = <8>;
+	 };
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};
-- 
1.7.10.4