Subject: [PATCH v2] ARM: AM43xx: hwmod: add VPFE hwmod entries

From: [email-masked] (Benoit Parrot)
Date: Mon, 26 Jan 2015 09:50:32 -0600

Lad, Prabhakar <[email-masked]> wrote on Mon [2015-Jan-26 08:13:01 +0000]:
> Hi Paul,
> 
> Thanks for the review.
> 
> On Mon, Jan 26, 2015 at 2:15 AM, Paul Walmsley <[email-masked]> wrote:
> > Hi
> >
> > On Sun, 25 Jan 2015, Lad, Prabhakar wrote:
> >
> >> From: Benoit Parrot <[email-masked]>
> >>
> >> this patch adds VPFE HWMOD data for AM43xx.
> >>
> >> Signed-off-by: Benoit Parrot <[email-masked]>
> >> Signed-off-by: Darren Etheridge <[email-masked]>
> >> Signed-off-by: Felipe Balbi <[email-masked]>
> >> Signed-off-by: Lad, Prabhakar <[email-masked]>
> >> ---
> >>  Hi Paul,
> >>
> >>  You were right, the hardware team has confirmed that, the VPFE master port is
> >>  connected to L3 and the VPFE slave port is connected to L4. The L3 port cannot
> >>  serve as a register target because it is initiator only.
> >
> > OK makes sense to me.,
> >
> >>
> >>  I have created links referring to dss l3/l4 hwmod and tested it, lemme know
> >>  if I have missed something.
> >
> > A few minor comments below
> >
> >>
> [Snip]
> >>  /* Interfaces */
> >>  static struct omap_hwmod_ocp_if am43xx_l3_main__l4_hs = {
> >>       .master         = &am33xx_l3_main_hwmod,
> >> @@ -788,6 +826,36 @@ static struct omap_hwmod_ocp_if am43xx_l4_ls__dss_rfbi = {
> >>       .user           = OCP_USER_MPU | OCP_USER_SDMA,
> >>  };
> >>
> >> +static struct omap_hwmod_ocp_if am43xx_l3__vpfe0 = {
> >> +     .master         = &am43xx_vpfe0_hwmod,
> >> +     .slave          = &am33xx_l3_main_hwmod,
> >> +     .clk            = "l3_gclk",
> >> +     .flags          = OCPIF_SWSUP_IDLE,
> >
> > OCPIF_SWSUP_IDLE probably isn't needed here.  Could you please try without
> > it?
> >
> >> +     .user           = OCP_USER_MPU | OCP_USER_SDMA,
> >> +};
> >> +
> >> +static struct omap_hwmod_ocp_if am43xx_l3__vpfe1 = {
> >> +     .master         = &am43xx_vpfe1_hwmod,
> >> +     .slave          = &am33xx_l3_main_hwmod,
> >> +     .clk            = "l3_gclk",
> >> +     .flags          = OCPIF_SWSUP_IDLE,
> >
> > Same point as the above.
> >
> Dropped and tested works! posting a v3.

When you tested it without the OCPIF_SWSUP_IDLE, did you go trhough a complete suspend/resume cycle?
This flag was added early on because otherwise the susbsytem would not go idle without it...

Can you post the console output during a suspend/resume cycle?

Benoit

> Cheers,
> --Prabhakar Lad