Subject: [PATCH v7 1/2] mfd: devicetree: add bindings for Atmel Flexcom

From: [email-masked] (Lee Jones)
Date: Fri, 24 Jul 2015 15:56:13 +0100

On Fri, 24 Jul 2015, Nicolas Ferre wrote:

> Le 23/07/2015 21:48, Boris Brezillon a ?crit :
> > On Thu, 23 Jul 2015 18:42:55 +0200
> > Cyrille Pitchen <[email-masked]> wrote:
> > 
> >> This patch documents the DT bindings for the Atmel Flexcom which will be
> >> introduced by sama5d2x SoCs. These bindings will be used by the actual
> >> Flexcom driver to be sent in another patch.
> >>
> >> Signed-off-by: Cyrille Pitchen <[email-masked]>
> >> ---
> >>  .../devicetree/bindings/mfd/atmel-flexcom.txt      | 68 ++++++++++++++++++++++
> >>  1 file changed, 68 insertions(+)
> >>  create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
> >>
> >> diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
> >> new file mode 100644
> >> index 000000000000..a63226b7a9cb
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
> >> @@ -0,0 +1,68 @@
> >> +* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit)
> >> +
> >> +The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C
> >> +controller and an USART. Only one function can be used at a time and is chosen
> >> +at boot time according to the device tree.
> >> +
> >> +Required properties:
> >> +- compatible:		Should be "atmel,sama5d2-flexcom"
> >> +- reg:			Should be the pair (offset, size) for the Flexcom
> >> +			dedicated I/O registers (without USART, TWI or SPI
> >> +			registers).
> >> +- clocks:		Should be the Flexcom peripheral clock from PMC.
> >> +- #address-cells:	Should be <2>
> >> +- #size-cells:		Should be <1>
> >> +- ranges:		Should be a list of ranges.
> >> +			One range per peripheral wrapped by the Flexcom. So each
> >> +			range is a triplet (child_addr, parent_addr, size). The
> >> +			first u32 of "child_addr" is the value to be set in the
> >> +			Operating Mode bitfield of the Flexcom Mode Register.
> >> +			Then "parent_addr" stores the base address of the
> >> +			corresponding peripheral in the system memory. Finally,
> >> +			"size" if the size of the memory region of this
> >> +			peripheral.
> >> +
> >> +Required child:
> >> +A single available child for the serial controller to enable.
> >> +
> >> +Required properties of this child:
> >> +- reg:			Should be a pair (child_addr, size) with child_addr
> >> +			matching one of the parent ranges.
> >> +- clocks:		Should be the very same phandle as for the parent's one.
> >> +
> >> +Other properties remain unchanged. See documentation of the respective device:
> >> +- ../serial/atmel-usart.txt
> >> +- ../spi/spi_atmel.txt
> >> +- ../i2c/i2c-at91.txt
> >> +
> >> +Example:
> >> +
> >> +flexcom at f8034000 {
> >> +	compatible = "atmel,sama5d2-flexcom";
> >> +	reg = <0xf8034000 0x200>;
> >> +	clocks = <&flx0_clk>;
> >> +	#address-cells = <2>;
> >> +	#size-cells = <1>;
> >> +	ranges = <1 0 0xf8034200 0x200		/* opmode 1: USART */
> >> +		  2 0 0xf8034400 0x200		/* opmode 2: SPI */
> >> +		  3 0 0xf8034600 0x200>;	/* opmode 3: I2C */
> 
> Yes, the opmode(s) are exactly the values described in the product
> datasheet.
> 
> >> +
> >> +	spi at f8034400 {
> > 
> > Should be:
> > 
> > 	spi at 2,0 {
> 
> Yep!
> 
> I was silently following the discussion in the background and I admit
> that this approach is pretty elegant.
> 
> So, if this approach is validated you can also add my:
> Acked-by: Nicolas Ferre <[email-masked]>

Please see my reply to v6 for the usual way to achieve this.

> >> +		compatible = "atmel,at91rm9200-spi";
> >> +		reg = <2 0 0x200>;
> >> +		interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
> >> +		pinctrl-names = "default";
> >> +		pinctrl-0 = <&pinctrl_flx0_default>;
> >> +		#address-cells = <1>;
> >> +		#size-cells = <0>;
> >> +		clocks = <&flx0_clk>;
> >> +		clock-names = "spi_clk";
> >> +		atmel,fifo-size = <32>;
> >> +
> >> +		mtd_dataflash at 0 {
> >> +			compatible = "atmel,at25f512b";
> >> +			reg = <0>;
> >> +			spi-max-frequency = <20000000>;
> >> +		};
> >> +	};
> >> +};
> > 
> > 
> > 
> 
> 

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog