Subject: [PATCH-v2 4/7] mmc: sdhci-pxav3: Add pinctl setting according to bus clock

From: [email-masked] (Jisheng Zhang)
Date: Tue, 8 Sep 2015 14:54:39 +0800

On Mon, 7 Sep 2015 16:48:38 +0530
Vaibhav Hiremath <[email-masked]> wrote:

> Different bus clock may need different pin setting.
> For example, fast bus clock like 208Mhz need pin drive fast
> while slow bus clock prefer pin drive slow to guarantee
> signal quality.
> 
> So this patch creates two states,
>   - Default (slow/normal) pin state
>   - And fast pin state for higher freq bus speed.
> 
> And selection of pin state is done based on timing mode.
> 
> Signed-off-by: Vaibhav Hiremath <[email-masked]>
> Signed-off-by: Kevin Liu <[email-masked]>
> ---
>  drivers/mmc/host/sdhci-pxav3.c | 45 +++++++++++++++++++++++++++++++++++++++++-
>  1 file changed, 44 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/mmc/host/sdhci-pxav3.c b/drivers/mmc/host/sdhci-pxav3.c
> index c2b2b78..d933f75 100644
> --- a/drivers/mmc/host/sdhci-pxav3.c
> +++ b/drivers/mmc/host/sdhci-pxav3.c
> @@ -35,6 +35,7 @@
>  #include <linux/pm.h>
>  #include <linux/pm_runtime.h>
>  #include <linux/mbus.h>
> +#include <linux/pinctrl/consumer.h>
>  
>  #include "sdhci.h"
>  #include "sdhci-pltfm.h"
> @@ -92,6 +93,10 @@ struct sdhci_pxa {
>  	void __iomem *io_pwr_reg;
>  	void __iomem *io_pwr_lock_reg;
>  	struct sdhci_pxa_data *data;
> +
> +	struct pinctrl *pinctrl;
> +	struct pinctrl_state *pins_default;
> +	struct pinctrl_state *pins_fast;
>  };
>  
>  static struct sdhci_pxa_data pxav3_data_v1 = {
> @@ -298,6 +303,33 @@ static void pxav3_gen_init_74_clocks(struct sdhci_host *host, u8 power_mode)
>  	pxa->power_mode = power_mode;
>  }
>  
> +static int pxav3_select_pinstate(struct sdhci_host *host, unsigned int uhs)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct sdhci_pxa *pxa = pltfm_host->priv;
> +	struct pinctrl_state *pinctrl;
> +
> +	if (IS_ERR(pxa->pinctrl) ||
> +		IS_ERR(pxa->pins_default) ||
> +		IS_ERR(pxa->pins_fast))
> +		return -EINVAL;
> +
> +	switch (uhs) {
> +	case MMC_TIMING_UHS_SDR50:
> +	case MMC_TIMING_UHS_SDR104:
> +	case MMC_TIMING_MMC_HS200:
> +	case MMC_TIMING_MMC_HS400:

Are you sure this IP can support HS400?

> +		pinctrl = pxa->pins_fast;
> +		break;
> +	default:
> +		/* back to default state for other legacy timing */
> +		pinctrl = pxa->pins_default;
> +		break;
> +	}
> +
> +	return pinctrl_select_state(pxa->pinctrl, pinctrl);
> +}
> +
>  static void pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
>  {
>  	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> @@ -353,6 +385,8 @@ static void pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
>  	dev_dbg(mmc_dev(host->mmc),
>  		"%s uhs = %d, ctrl_2 = %04X\n",
>  		__func__, uhs, ctrl_2);
> +
> +	pxav3_select_pinstate(host, uhs);
>  }
>  
>  static void pxav3_voltage_switch(struct sdhci_host *host,
> @@ -416,7 +450,6 @@ static void pxav3_set_clock(struct sdhci_host *host, unsigned int clock)
>  		/* TX internal clock selection */
>  		pxav3_set_tx_clock(host);
>  	}
> -
>  }
>  
>  static const struct sdhci_ops pxav3_sdhci_ops = {
> @@ -586,6 +619,16 @@ static int sdhci_pxav3_probe(struct platform_device *pdev)
>  		}
>  	}
>  
> +	pxa->pinctrl = devm_pinctrl_get(dev);
> +	if (!IS_ERR(pxa->pinctrl)) {
> +		pxa->pins_default = pinctrl_lookup_state(pxa->pinctrl, "default");
> +		if (IS_ERR(pxa->pins_default))
> +			dev_err(dev, "could not get default pinstate\n");
> +		pxa->pins_fast = pinctrl_lookup_state(pxa->pinctrl, "fast");
> +		if (IS_ERR(pxa->pins_fast))
> +			dev_info(dev, "could not get fast pinstate\n");
> +	}
> +
>  	pm_runtime_get_noresume(&pdev->dev);
>  	pm_runtime_set_active(&pdev->dev);
>  	pm_runtime_set_autosuspend_delay(&pdev->dev, PXAV3_RPM_DELAY_MS);