Subject: [PATCH v6 4/7] ARM: dts: imx: Add support for Advantech/GE Bx50v3

From: [email-masked] (Shawn Guo)
Date: Thu, 28 Jan 2016 14:12:03 +0800

On Wed, Dec 23, 2015 at 05:00:13PM -0500, Akshay Bhat wrote:
> From: Justin Waters <[email-masked]>
> 
> Advantech has 3 carrier boards (B450v3, B650v3, B850v3) which use
> the Advantech BA-16 module (based on iMX6D). This file has the
> devicetree entries that are common to all 3 boards.
> 
> Signed-off-by: Akshay Bhat <[email-masked]>
> ---
>  arch/arm/boot/dts/imx6q-bx50v3.dtsi | 237 ++++++++++++++++++++++++++++++++++++
>  1 file changed, 237 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6q-bx50v3.dtsi
> 
> diff --git a/arch/arm/boot/dts/imx6q-bx50v3.dtsi b/arch/arm/boot/dts/imx6q-bx50v3.dtsi
> new file mode 100644
> index 0000000..1eaf0ce
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-bx50v3.dtsi
> @@ -0,0 +1,237 @@
> +/*
> + * Copyright 2015 Timesys Corporation.
> + * Copyright 2015 General Electric Company
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License
> + *     version 2 as published by the Free Software Foundation.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "imx6q-ba16.dtsi"
> +
> +/ {
> +	clocks {
> +		#address-cells = <1>;
> +		#size-cells = <0>;

Have a new line between properties and sub-node.

> +		mclk: clock at 0 {
> +			compatible = "fixed-clock";
> +			reg = <0>;
> +			#clock-cells = <0>;
> +			clock-frequency = <22000000>;
> +		};

So it's using a different clock naming schema from clk24m in
imx6q-ba16.dtsi.  In any case, they should be consistent.

> +	};
> +
> +	reg_wl18xx_vmmc: regulator-wl18xx_vmmc {

As a convention, hyphen instead of underscore should be used in node
name.  Actually less hyphen form like regulator-wl18xxvmmc or
regulator-wl18xx looks better to me.

> +		compatible = "regulator-fixed";
> +		regulator-name = "vwl1807";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&pca9539 3 GPIO_ACTIVE_HIGH>;
> +		startup-delay-us = <70000>;
> +		enable-active-high;
> +	};
> +
> +	reg_wlan: regulator-wlan {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3P3V_wlan";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +		gpio = <&gpio6 14 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	sound {
> +		compatible = "fsl,imx6q-ba16-sgtl5000",
> +			     "fsl,imx-audio-sgtl5000";
> +		model = "imx6q-ba16-sgtl5000";
> +		ssi-controller = <&ssi1>;
> +		audio-codec = <&codec>;
> +		audio-routing =
> +			"MIC_IN", "Mic Jack",
> +			"Mic Jack", "Mic Bias",
> +			"LINE_IN", "Line In Jack",
> +			"Headphone Jack", "HP_OUT";
> +		mux-int-port = <1>;
> +		mux-ext-port = <4>;
> +	};
> +};
> +
> +&ecspi5 {
> +	fsl,spi-num-chipselects = <1>;
> +	cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi5>;
> +	status = "okay";
> +
> +	m25_eeprom: m25p80 at 0 {
> +		compatible = "atmel,at25";
> +		spi-max-frequency = <20000000>;
> +		size = <0x8000>;
> +		pagesize = <64>;
> +		reg = <0>;
> +		address-width = <16>;
> +	};
> +};
> +
> +&i2c1 {
> +	pca9547: mux at 70 {
> +		compatible = "nxp,pca9547";
> +		reg = <0x70>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		mux_i2c3: i2c at 0 {

How are these mux_i2c labels named?  Where are mux_i2c1 and mux_i2c2?

> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x0>;
> +
> +			ads7830: ads7830 at 48 {
> +				compatible = "ti,ads7830";
> +				reg = <0x48>;
> +			};
> +
> +			mma8453: mma8453 at 1c {
> +				compatible = "fsl,mma8453";
> +				reg = <0x1c>;
> +			};
> +		};
> +
> +		mux_i2c4: i2c at 1 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x1>;
> +
> +			eeprom: eeprom at 50 {
> +				compatible = "atmel,24c08";
> +				reg = <0x50>;
> +			};
> +
> +			mpl3115: mpl3115 at 60 {
> +				compatible = "fsl,mpl3115";
> +				reg = <0x60>;
> +			};
> +		};
> +
> +		mux_i2c5: i2c at 2 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x2>;
> +		};
> +
> +		mux_i2c6: i2c at 3 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x3>;
> +
> +			codec: sgtl5000 at 0a {
> +				compatible = "fsl,sgtl5000";
> +				reg = <0x0a>;
> +				clocks = <&mclk>;
> +				VDDA-supply = <&reg_1p8v>;
> +				VDDIO-supply = <&reg_3p3v>;
> +			};
> +		};
> +
> +		mux_i2c7: i2c at 4 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x4>;
> +
> +			pca9539: pca9539 at 74 {
> +				compatible = "nxp,pca9539";
> +				reg = <0x74>;
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +				interrupt-controller;
> +				interrupt-parent = <&gpio2>;
> +				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +			};
> +		};
> +
> +		mux_i2c8: i2c at 5 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x5>;
> +
> +			igb at 49 {
> +				compatible = "intel,igb";
> +				reg = <0x49>;
> +			};
> +
> +			igb at 61 {
> +				compatible = "intel,igb";
> +				reg = <0x61>;
> +			};
> +		};
> +
> +		mux_i2c9: i2c at 6 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x6>;
> +		};
> +
> +		mux_i2c10: i2c at 7 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x7>;
> +		};
> +	};
> +};
> +
> +&usdhc4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc4>;
> +	bus-width = <4>;
> +	vmmc-supply = <&reg_wl18xx_vmmc>;
> +	no-1-8-v;
> +	non-removable;
> +	enable-sdio-wakeup;

wakeup-source

Shawn

> +	keep-power-in-suspend;
> +	cap-power-off-card;
> +	max-frequency = <25000000>;
> +	status = "okay";
> +
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	wlcore: wlcore at 0 {
> +		compatible = "ti,wl1837";
> +		reg = <2>;
> +		interrupt-parent = <&gpio2>;
> +		interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
> +		tcxo-clock-frequency = <26000000>;
> +	};
> +};
> -- 
> 2.6.3
> 
>