From: kishon@ti•com (Kishon Vijay Abraham I)
To: linux-arm-kernel@lists•infradead.org
Subject: [PATCH 25/41] ARM: dts: dra7-evm: Add pinmux configuration for MMC
Date: Fri, 19 May 2017 13:45:25 +0530 [thread overview]
Message-ID: <20170519081541.26753-26-kishon@ti.com> (raw)
In-Reply-To: <20170519081541.26753-1-kishon@ti.com>
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra7-evm.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti•com>
---
arch/arm/boot/dts/dra7-evm.dts | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index fbcb3199defd..64955e8f06d2 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -8,6 +8,7 @@
/dts-v1/;
#include "dra74x.dtsi"
+#include "dra74x-mmc-iodelay.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clk/ti-dra7-atl.h>
#include <dt-bindings/input/input.h>
@@ -451,6 +452,16 @@
* is always hardwired.
*/
cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104";
+ pinctrl-0 = <&mmc1_pins_default>;
+ pinctrl-1 = <&mmc1_pins_hs>;
+ pinctrl-2 = <&mmc1_pins_sdr12>;
+ pinctrl-3 = <&mmc1_pins_sdr25>;
+ pinctrl-4 = <&mmc1_pins_sdr50>;
+ pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>;
+ pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
+ pinctrl-7 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
+ pinctrl-8 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
};
&mmc2 {
@@ -459,6 +470,13 @@
pinctrl-0 = <&mmc2_pins_default>;
vmmc-supply = <&evm_1v8_sw>;
bus-width = <8>;
+ pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v";
+ pinctrl-0 = <&mmc2_pins_default>;
+ pinctrl-1 = <&mmc2_pins_hs>;
+ pinctrl-2 = <&mmc2_pins_ddr_1_8v_rev11 &mmc2_iodelay_ddr_1_8v_rev11_conf>;
+ pinctrl-3 = <&mmc2_pins_ddr_rev20>;
+ pinctrl-4 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev11_conf>;
+ pinctrl-5 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
};
&cpu0 {
--
2.11.0
next prev parent reply other threads:[~2017-05-19 8:15 UTC|newest]
Thread overview: 46+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-05-19 8:15 [PATCH 00/41] omap_hsmmc: Add ADMA support and UHS/HS200/DDR support Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 01/41] mmc: host: omap_hsmmc: Support pbias and vmmc_aux to switch to 1.8v Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 02/41] mmc: host: omap_hsmmc: Separate setting voltage capabilities from bus power Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 03/41] mmc: host: omap_hsmmc: Program HCTL based on signal_voltage set by mmc core Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 04/41] mmc: host: omap_hsmmc: Add voltage switch support for UHS SD card Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 05/41] mmc: host: omap_hsmmc: Set clk rate to the max frequency Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 06/41] mmc: host: omap_hsmmc: Add tuning support Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 07/41] mmc: host: omap_hsmmc: Allow io voltage switch even for fixed vdd Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 08/41] mmc: host: omap_hsmmc: Remove incorrect voltage switch sequence Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 09/41] mmc: host: omap_hsmmc: Add software timer when timeout greater than hardware capablility Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 10/41] mmc: host: omap_hsmmc: Prepare *set_timing() to be used for iodelay setting Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 11/41] mmc: host: omap_hsmmc: Add new compatible string to support dra7 Kishon Vijay Abraham I
2017-05-23 14:44 ` Rob Herring
2017-05-19 8:15 ` [PATCH 12/41] mmc: host: omap_hsmmc: Fix error path sequence Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 13/41] mmc: host: omap_hsmmc: Add support to set IODELAY values Kishon Vijay Abraham I
2017-05-23 14:55 ` Rob Herring
2017-05-19 8:15 ` [PATCH 14/41] mmc: host: omap_hsmmc: Remove *use_dma* member Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 15/41] mmc: host: omap_hsmmc: Enable ADMA2 Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 16/41] mmc: omap_hsmmc: Support non-1.8V IO controllers Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 17/41] ARM: dts: dra72-evm: Add vmmc_aux supply to mmc1 Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 18/41] ARM: dts: dra72-evm-revc: " Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 19/41] ARM: dts: am57xx-beagle-x15-revb1: Fix supply name used for MMC1 IO lines Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 20/41] ARM: dts: dra7-evm: Correct the vmmc-supply for mmc2 Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 21/41] ARM: dts: dra72-evm-common: Correct " Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 22/41] ARM: dts: Add dra7 iodelay configuration Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 23/41] ARM: dts: dra72x: Create a common file with MMC/SD IOdelay data Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 24/41] ARM: dts: dra74x: " Kishon Vijay Abraham I
2017-05-19 8:15 ` Kishon Vijay Abraham I [this message]
2017-05-19 8:15 ` [PATCH 26/41] ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 27/41] ARM: dts: am57xx-idk: Move common MMC/SD properties to common file Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 28/41] ARM: dts: am571x-idk: Add pinmux configuration for MMC Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 29/41] ARM: dts: am572x-idk: " Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 30/41] ARM: dts: dra72-evm: " Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 31/41] ARM: dts: dra72-evm-revc: " Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 32/41] ARM: dts: dra71-evm: " Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 33/41] ARM: dts: dra7: Add "max-frequency" property to MMC dt nodes Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 34/41] ARM: dts: dra7: Use new dra7-specific compatible string Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 35/41] ARM: dts: dra7: Add supported MMC/SD modes in MMC dt nodes Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 36/41] ARM: dts: am57xx-idk: Set MMC2 IO voltage to 3.3V Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 37/41] ARM: dts: am57xx-beagle-x15-common: " Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 38/41] ARM: OMAP2+: Add pdata-quirks for MMC/SD on DRA74x EVM Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 39/41] ARM: omap2plus_defconfig: Enable PINCTRL_TI_IODELAY Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 40/41] ARM: multi_v7_defconfig: " Kishon Vijay Abraham I
2017-05-19 8:15 ` [PATCH 41/41] Documentation: ARM: Document new dependencies for MMC on DRA7 Kishon Vijay Abraham I
2017-05-19 22:13 ` [PATCH 00/41] omap_hsmmc: Add ADMA support and UHS/HS200/DDR support Tony Lindgren
2017-05-22 12:20 ` Kishon Vijay Abraham I
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170519081541.26753-26-kishon@ti.com \
--to=kishon@ti$(echo .)com \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox