Subject: [PATCH v2] ARM: dts: imx6qdl-wandboard: enable USB OTG

From: [email-masked] (Shawn Guo)
Date: Wed, 26 Jul 2017 10:36:54 +0800

On Sun, Jul 23, 2017 at 06:49:12PM +0200, Alexander Kurz wrote:
> Enable USB OTG (dual-role) on the Wandboard.
> Note, that the USB_OTG_VBUS current is quite limited due to a 22R resistor
> in the power line. Hence, the overcurrent signal of 1A will never be
> triggered on this board.
> 
> Signed-off-by: Alexander Kurz <[email-masked]>
> ---

When sending a version, it's helpful to have a change log here.

>  arch/arm/boot/dts/imx6qdl-wandboard.dtsi | 19 ++++++++++++++++++-
>  1 file changed, 18 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
> index b4fa7f1..f1abde8 100644
> --- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
> @@ -34,6 +34,16 @@
>  			regulator-max-microvolt = <3300000>;
>  			regulator-always-on;
>  		};
> +
> +		reg_usb_otg_vbus: usb_otg_vbus {

You are trying to add a fixed regulator under regulators bus node
without sticking to the existing convention.  I understand that it's
now preferred to put fixed regulator node directly under root node, but
mixing two styles is not good either.

I suggest you order a patch to remove regulators bus node and name node
like below:

	reg_xxx: regulator-xxx {
		...
	};

And then add your changes on top of that.

Shawn

> +			compatible = "regulator-fixed";
> +			regulator-name = "usb_otg_vbus";
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_usbotgvbus>;
> +			gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
> +		};
>  	};
>  
>  	sound {
> @@ -170,6 +180,12 @@
>  			>;
>  		};
>  
> +		pinctrl_usbotgvbus: usbotgvbusgrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x130b0
> +			>;
> +		};
> +
>  		pinctrl_usdhc1: usdhc1grp {
>  			fsl,pins = <
>  				MX6QDL_PAD_SD1_CMD__SD1_CMD		0x17059
> @@ -244,10 +260,11 @@
>  };
>  
>  &usbotg {
> +	vbus-supply = <&reg_usb_otg_vbus>;
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_usbotg>;
>  	disable-over-current;
> -	dr_mode = "peripheral";
> +	dr_mode = "otg";
>  	status = "okay";
>  };
>  
> -- 
> 2.1.4
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel