Subject: [PATCH v4 1/3] Input: edt-ft5x06 - Add support for regulator

From: [email-masked] (Dmitry Torokhov)
Date: Wed, 25 Jul 2018 17:47:32 -0700

Hi Myl?ne,

On Wed, Jul 25, 2018 at 09:34:08AM +0200, Myl?ne Josserand wrote:
> Add the support of regulator to use it as VCC source.
> 
> Signed-off-by: Myl?ne Josserand <[email-masked]>
> Reviewed-by: Rob Herring <[email-masked]>
> ---
>  .../bindings/input/touchscreen/edt-ft5x06.txt      |  1 +
>  drivers/input/touchscreen/edt-ft5x06.c             | 43 ++++++++++++++++++++++
>  2 files changed, 44 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> index 025cf8c9324a..48e975b9c1aa 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> @@ -30,6 +30,7 @@ Required properties:
>  Optional properties:
>   - reset-gpios: GPIO specification for the RESET input
>   - wake-gpios:  GPIO specification for the WAKE input
> + - vcc-supply:  Regulator that supplies the touchscreen
>  
>   - pinctrl-names: should be "default"
>   - pinctrl-0:   a phandle pointing to the pin settings for the
> diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> index 1e18ca0d1b4e..dcde719094f7 100644
> --- a/drivers/input/touchscreen/edt-ft5x06.c
> +++ b/drivers/input/touchscreen/edt-ft5x06.c
> @@ -39,6 +39,7 @@
>  #include <linux/input/mt.h>
>  #include <linux/input/touchscreen.h>
>  #include <linux/of_device.h>
> +#include <linux/regulator/consumer.h>
>  
>  #define WORK_REGISTER_THRESHOLD		0x00
>  #define WORK_REGISTER_REPORT_RATE	0x08
> @@ -91,6 +92,7 @@ struct edt_ft5x06_ts_data {
>  	struct touchscreen_properties prop;
>  	u16 num_x;
>  	u16 num_y;
> +	struct regulator *vcc;
>  
>  	struct gpio_desc *reset_gpio;
>  	struct gpio_desc *wake_gpio;
> @@ -963,6 +965,13 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
>  	}
>  }
>  
> +static void edt_ft5x06_disable_regulator(void *arg)
> +{
> +	struct edt_ft5x06_ts_data *data = arg;
> +
> +	regulator_disable(data->vcc);
> +}
> +
>  static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  					 const struct i2c_device_id *id)
>  {
> @@ -991,6 +1000,28 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  
>  	tsdata->max_support_points = chip_data->max_support_points;
>  
> +	tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
> +	if (IS_ERR(tsdata->vcc)) {
> +		error = PTR_ERR(tsdata->vcc);
> +		if (error != -EPROBE_DEFER)
> +			dev_err(&client->dev, "failed to request regulator: %d\n",
> +				error);
> +		return error;
> +	}
> +
> +	error = regulator_enable(tsdata->vcc);
> +	if (error < 0) {
> +		dev_err(&client->dev, "failed to enable vcc: %d\n",
> +			error);
> +		return error;
> +	}

It is better to put the chip into reset and then power up the regulatori
and take it out of the reset, rather than power up and then toggle reset
on and off.

> +
> +	error = devm_add_action_or_reset(&client->dev,
> +					 edt_ft5x06_disable_regulator,
> +					 tsdata);
> +	if (error)
> +		return error;
> +
>  	tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
>  						     "reset", GPIOD_OUT_HIGH);
>  	if (IS_ERR(tsdata->reset_gpio)) {
> @@ -1120,9 +1151,12 @@ static int edt_ft5x06_ts_remove(struct i2c_client *client)
>  static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
>  {
>  	struct i2c_client *client = to_i2c_client(dev);
> +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
>  
>  	if (device_may_wakeup(dev))
>  		enable_irq_wake(client->irq);
> +	else
> +		regulator_disable(tsdata->vcc);
>  
>  	return 0;
>  }
> @@ -1130,9 +1164,18 @@ static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
>  static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
>  {
>  	struct i2c_client *client = to_i2c_client(dev);
> +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> +	int ret;
>  
>  	if (device_may_wakeup(dev))
>  		disable_irq_wake(client->irq);
> +	else {
> +		ret = regulator_enable(tsdata->vcc);
> +		if (ret < 0) {
> +			dev_err(dev, "failed to enable vcc: %d\n", ret);
> +			return ret;
> +		}
> +	}

I believe I mentioned in other review that once you powered up the
device, you need to restore its settings, include switching to factory
mode, if it was in factory mode, and restoring threshold/gain/offset
settings.

Thanks.

-- 
Dmitry