Subject: Re: [PATCH v4 4/4] PCI: imx6: Add support for i.MX8MQ

From: Rob Herring <[email-masked]>
Date: Fri, 11 Jan 2019 13:53:02 -0600

On Fri, Jan 04, 2019 at 08:53:35AM -0800, Andrey Smirnov wrote:
> Add code needed to support i.MX8MQ variant.
> 
> Cc: Bjorn Helgaas <[email-masked]>
> Cc: Fabio Estevam <[email-masked]>
> Cc: Chris Healy <[email-masked]>
> Cc: Lucas Stach <[email-masked]>
> Cc: Leonard Crestez <[email-masked]>
> Cc: "A.s. Dong" <[email-masked]>
> Cc: Richard Zhu <[email-masked]>
> Cc: Rob Herring <[email-masked]>,
> Cc: [email-masked],
> Cc: [email-masked]
> Cc: [email-masked]
> Cc: [email-masked]
> Cc: [email-masked]
> Signed-off-by: Andrey Smirnov <[email-masked]>
> ---
>  .../bindings/pci/fsl,imx6q-pcie.txt           |  3 +-
>  drivers/pci/controller/dwc/Kconfig            |  4 +-
>  drivers/pci/controller/dwc/pci-imx6.c         | 77 ++++++++++++++++++-
>  3 files changed, 79 insertions(+), 5 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> index d514c1f2365f..920ca93870a8 100644
> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> @@ -9,6 +9,7 @@ Required properties:
>  	- "fsl,imx6sx-pcie",
>  	- "fsl,imx6qp-pcie"
>  	- "fsl,imx7d-pcie"
> +	- "fsl,imx8mq-pcie"
>  - reg: base address and length of the PCIe controller
>  - interrupts: A list of interrupt outputs of the controller. Must contain an
>    entry for each entry in the interrupt-names property.
> @@ -45,7 +46,7 @@ Additional required properties for imx6sx-pcie:
>    PCIE_PHY power domains
>  - power-domain-names: Must be "pcie", "pcie_phy"
>  
> -Additional required properties for imx7d-pcie:
> +Additional required properties for imx7d-pcie and imx8mq-pcie:
>  - power-domains: Must be set to a phandle pointing to PCIE_PHY power domain
>  - resets: Must contain phandles to PCIe-related reset lines exposed by SRC
>    IP block
> diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> index 6aafec3fad00..83ea318ad989 100644
> --- a/drivers/pci/controller/dwc/Kconfig
> +++ b/drivers/pci/controller/dwc/Kconfig
> @@ -89,8 +89,8 @@ config PCI_EXYNOS
>  	select PCIE_DW_HOST
>  
>  config PCI_IMX6
> -	bool "Freescale i.MX6/7 PCIe controller"
> -	depends on SOC_IMX6Q || SOC_IMX7D || (ARM && COMPILE_TEST)
> +	bool "Freescale i.MX6/7/8 PCIe controller"
> +	depends on SOC_IMX6Q || SOC_IMX7D || (ARM64 && ARCH_MXC) || ((ARM || ARM64) && COMPILE_TEST)

Since you added the ifdef around the abort handler, I think you can drop 
"(ARM || ARM64)" and enable building other arches.

Rob

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel