Subject: Re: [PATCH v4 1/6] dt-bindings: usb: musb: Add support for MediaTek musb controller

From: Rob Herring <[email-masked]>
Date: Mon, 21 Jan 2019 09:14:17 -0600

On Mon, Jan 21, 2019 at 08:22:26PM +0800, [email-masked] wrote:
> From: Min Guo <[email-masked]>
> 
> This adds support for MediaTek musb controller in
> host, peripheral and otg mode.
> 
> Signed-off-by: Min Guo <[email-masked]>
> ---
> changes in v4:
> suggested by Sergei:
> 1. String alignment
> 
> changes in v3:
> 1. no changes
> 
> changes in v2:
> suggested by Bin:
> 1. Modify DRC to DRD
> suggested by Rob:
> 2. Drop the "<soc-model>-musb" in compatible

This is not what I said. I gave you the exact text to put.

> 3. Remove phy-names
> 4. Add space after comma in clock-names
> ---
>  .../devicetree/bindings/usb/mediatek,musb.txt      | 43 ++++++++++++++++++++++
>  1 file changed, 43 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/usb/mediatek,musb.txt
> 
> diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
> new file mode 100644
> index 0000000..4305770
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
> @@ -0,0 +1,43 @@
> +MediaTek musb DRD/OTG controller
> +-------------------------------------------
> +
> +Required properties:
> + - compatible      : should be "mediatek,mtk-musb"
> + - reg             : specifies physical base address and size of
> +                     the registers
> + - interrupts      : interrupt used by musb controller
> + - interrupt-names : must be "mc"
> + - phys            : PHY specifier for the OTG phy
> + - dr_mode         : should be one of "host", "peripheral" or "otg",
> +                     refer to usb/generic.txt
> + - clocks          : a list of phandle + clock-specifier pairs, one for
> +                     each entry in clock-names
> + - clock-names     : must contain "main", "mcu", "univpll"
> +                     for clocks of controller
> +
> +Optional properties:
> + - extcon          : external connector for VBUS and ID pin changes detection,
> +                     needed when supports dual-role mode

Again, do not use extcon in new bindings.

> + - vbus-supply     : reference to the VBUS regulator, needed when supports
> +                     dual-role mode
> + - power-domains   : a phandle to USB power domain node to control USB's
> +                     MTCMOS
> +
> +Example:
> +
> +usb2: usb@11200000 {
> +	compatible = "mediatek,mt2701-musb",
> +		     "mediatek,mtk-musb";
> +	reg = <0 0x11200000 0 0x1000>;
> +	interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
> +	interrupt-names = "mc";
> +	phys = <&u2port2 PHY_TYPE_USB2>;
> +	vbus-supply = <&usb_vbus>;
> +	extcon = <&extcon_usb>;
> +	dr_mode = "otg";
> +	clocks = <&pericfg CLK_PERI_USB0>,
> +		 <&pericfg CLK_PERI_USB0_MCU>,
> +		 <&pericfg CLK_PERI_USB_SLV>;
> +	clock-names = "main","mcu","univpll";
> +	power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
> +};
> -- 
> 1.9.1
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> [email-masked]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel