Subject: Re: [PATCH v3 1/2] arm64: dts: fsl: add support for Hummingboard Pulse

From: Shawn Guo <[email-masked]>
Date: Mon, 19 Aug 2019 15:06:23 +0200

On Wed, Aug 14, 2019 at 04:37:04PM +0300, Baruch Siach wrote:
> From: Jon Nettleton <[email-masked]>
> 
> The SolidRun Hummingboard Pulse carrier board carries the SolidRun
> i.MX8MQ based SOM.
> 
> Notably missing is PCIe support that depends on analog PLLOUT clock.
> Current imx clk driver does not support this clock.
> 
> Signed-off-by: Jon Nettleton <[email-masked]>
> Signed-off-by: Baruch Siach <[email-masked]>
> ---
> v3:
>   Fix SD card power regulator enable gpio
>   Address Marco's comments:
>   - Reorder pinctrl properties
>   - Move imx8mq.dtsi include to the SOM .dtsi
>   - Add reg_ prefix to regulator labels
>   - Add pinctrl node to SD card regulator gpio
>   - Add label to SPI flash node
> 
> v2: Address Fabio's comments:
>   - Remove redundant node nesting
>   - Fix comments style
>   - Use mainline DT bindings in UART and USB type C
>   - Fix node names
>   - Move &iomuxc to the end of file
> ---
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../freescale/imx8mq-hummingboard-pulse.dts   | 256 +++++++++++++++
>  .../boot/dts/freescale/imx8mq-sr-som.dtsi     | 309 ++++++++++++++++++
>  3 files changed, 566 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index c043aca66572..6833b23e2dd2 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
>  
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts b/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts
> new file mode 100644
> index 000000000000..4beb3c456448
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts
> @@ -0,0 +1,256 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2018 Jon Nettleton <[email-masked]>
> + */
> +
> +/dts-v1/;
> +
> +#include "dt-bindings/usb/pd.h"
> +#include "imx8mq-sr-som.dtsi"
> +
> +/ {
> +	model = "SolidRun i.MX8MQ HummingBoard Pulse";
> +	compatible = "solidrun,hummingboard-pulse", "fsl,imx8mq";
> +
> +	chosen {
> +		stdout-path = &uart1;
> +	};
> +
> +	reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_usdhc2_vmmc>;
> +		regulator-name = "VSD_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio1 13 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	reg_v_5v0: regulator-v-5v0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v_5v0";
> +		regulator-max-microvolt = <5000000>;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +};
> +
> +&i2c2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c2>;
> +	clock-frequency = <100000>;
> +	status = "okay";
> +
> +	typec_ptn5100: usb-typec@50 {
> +		compatible = "nxp,ptn5110";
> +		reg = <0x50>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_typec>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
> +
> +		connector {
> +			compatible = "usb-c-connector";
> +			label = "USB-C";
> +			data-role = "dual";
> +			power-role = "dual";
> +			try-power-role = "sink";
> +			source-pdos = <PDO_FIXED(5000, 2000,
                                                 ^
> +				PDO_FIXED_USB_COMM |
> +				PDO_FIXED_SUSPEND |
> +				PDO_FIXED_EXTPOWER)>;

It'd be nice to have the lines align with column marked with ^ above.

> +			sink-pdos = <PDO_FIXED(5000, 2000,
                                     ^
> +					PDO_FIXED_USB_COMM |
> +					PDO_FIXED_SUSPEND |
> +					PDO_FIXED_EXTPOWER)
> +				PDO_FIXED(9000, 2000,

It'd be nice to have it align with column marked with ^ above.

> +					PDO_FIXED_USB_COMM |
> +					PDO_FIXED_SUSPEND |
> +					PDO_FIXED_EXTPOWER)>;
> +			op-sink-microwatt = <9000000>;
> +
> +			port {
> +				typec1_dr_sw: endpoint {
> +					remote-endpoint = <&usb1_drd_sw>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&i2c3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c3>;
> +	clock-frequency = <100000>;
> +	status = "okay";
> +
> +	rtc@69 {
> +		compatible = "abracon,ab1805";
> +		reg = <0x69>;
> +		abracon,tc-diode = "schottky";
> +		abracon,tc-resistor = <3>;
> +	};
> +};
> +
> +&uart2 { /* J35 header */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	assigned-clocks = <&clk IMX8MQ_CLK_UART2>;
> +	assigned-clock-parents = <&clk IMX8MQ_CLK_25M>;
> +	status = "okay";
> +};
> +
> +&uart3 { /* Mikrobus */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart3>;
> +	assigned-clocks = <&clk IMX8MQ_CLK_UART3>;
> +	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
> +	uart-has-rtscts;
> +	status = "okay";
> +};
> +
> +&usdhc2 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> +	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> +	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
> +	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> +	vmmc-supply = <&reg_usdhc2_vmmc>;
> +	status = "okay";
> +};
> +
> +&usb_dwc3_0 {
> +	status = "okay";
> +	dr_mode = "otg";

We usually put 'status' line at end of property list, so please flip them.

> +
> +	port {
> +		usb1_drd_sw: endpoint {
> +			remote-endpoint = <&typec1_dr_sw>;
> +		};
> +	};
> +};
> +
> +&usb_dwc3_1 {
> +	status = "okay";
> +	dr_mode = "host";
> +};
> +
> +&usb3_phy0 {
> +	status = "okay";
> +};
> +
> +&usb3_phy1 {
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_hog>;
> +
> +	pinctrl_hog: hoggrp {
> +		fsl,pins = <
> +			/* MikroBus Analog */
> +			MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11		0x41
> +			/* MikroBus Reset */
> +			MX8MQ_IOMUXC_SAI2_RXD0_GPIO4_IO23		0x41
> +			/*
> +			 * The following 2 pins need to be commented out and
> +			 * reconfigured to enable RTS/CTS on UART3
> +			 */
> +			/* MikroBus PWM */
> +			MX8MQ_IOMUXC_ECSPI1_MISO_GPIO5_IO8		0x41
> +			/* MikroBus INT */
> +			MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x41
> +		>;
> +	};
> +
> +	pinctrl_i2c2: i2c2grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL		0x4000007f
> +			MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA		0x4000007f
> +		>;
> +	};
> +
> +	pinctrl_i2c3: i2c3grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL		0x4000007f
> +			MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA		0x4000007f
> +		>;
> +	};
> +
> +	pinctrl_typec: typecgrp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15	0x16
> +			MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6	0x17059
> +		>;
> +	};
> +
> +	pinctrl_uart2: uart2grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x49
> +			MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX		0x49
> +		>;
> +	};
> +
> +	pinctrl_uart3: uart3grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX		0x49
> +			MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX		0x49
> +			/*
> +			 * These pins are by default GPIO on the Mikro Bus
> +			 * Header. To use RTS/CTS on UART3 comment them out
> +			 * of the hoggrp and enable them here
> +			 */
> +			/* MX8MQ_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x49 */
> +			/* MX8MQ_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B	0x49 */
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_gpio: usdhc2grpgpio {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12	0x41
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_vmmc: usdhc2vmmcgpio {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x41
> +		>;
> +	};
> +
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
> +			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
> +			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3
> +			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc3
> +			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc3
> +			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc3
> +			MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x8d
> +			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xcd
> +			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xcd
> +			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xcd
> +			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xcd
> +			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xcd
> +			MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x9f
> +			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xdf
> +			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xdf
> +			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xdf
> +			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xdf
> +			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xdf
> +			MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xc1
> +		>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi
> new file mode 100644
> index 000000000000..cd22d085d6c7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi
> @@ -0,0 +1,309 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2018 Jon Nettleton <[email-masked]>
> + */
> +
> +#include "imx8mq.dtsi"
> +
> +/ {
> +	reg_vdd_3v3: regulator-vdd-3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-always-on;
> +		regulator-name = "vdd_3v3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +};
> +
> +&pgc_gpu{
> +	power-supply = <&sw1a_reg>;
> +};
> +
> +&fec1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_fec1>;
> +	phy-mode = "rgmii-id";
> +	phy-handle = <&ethphy0>;
> +	phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
> +	phy-reset-duration = <2>;
> +	fsl,magic-packet;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy@4 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <4>;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	pmic: pmic@8 {
> +		compatible = "fsl,pfuze100";
> +		reg = <0x08>;
> +
> +		regulators {
> +			sw1a_reg: sw1ab {
> +				regulator-min-microvolt = <300000>;
> +				regulator-max-microvolt = <1875000>;
> +			};
> +
> +			sw1c_reg: sw1c {
> +				regulator-min-microvolt = <300000>;
> +				regulator-max-microvolt = <1875000>;
> +			};
> +
> +			sw2_reg: sw2 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			sw3a_reg: sw3ab {
> +				regulator-min-microvolt = <400000>;
> +				regulator-max-microvolt = <1975000>;
> +				regulator-always-on;
> +			};
> +
> +			sw4_reg: sw4 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			swbst_reg: swbst {
> +				regulator-min-microvolt = <5000000>;
> +				regulator-max-microvolt = <5150000>;
> +			};
> +
> +			snvs_reg: vsnvs {
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-always-on;
> +			};
> +
> +			vref_reg: vrefddr {
> +				regulator-always-on;
> +			};
> +
> +			vgen1_reg: vgen1 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1550000>;
> +			};
> +
> +			vgen2_reg: vgen2 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1550000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen3_reg: vgen3 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen4_reg: vgen4 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen5_reg: vgen5 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen6_reg: vgen6 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +		};
> +	};
> +};
> +
> +&qspi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_qspi>;
> +	status = "okay";
> +
> +	/* SPI flash; not assembled by default */
> +	spi_flash: flash@0 {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		reg = <0>;
> +		compatible = "micron,n25q256a", "jedec,spi-nor";
> +		spi-max-frequency = <29000000>;
> +		status = "disabled";
> +	};
> +};
> +
> +&uart1 { /* console */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	assigned-clocks = <&clk IMX8MQ_CLK_UART1>;
> +	assigned-clock-parents = <&clk IMX8MQ_CLK_25M>;
> +	assigned-clock-rates = <25000000>;
> +	status = "okay";
> +};
> +
> +&uart4 { /* ublox BT */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart4>;
> +	assigned-clocks = <&clk IMX8MQ_CLK_UART4>;
> +	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
> +	assigned-clock-rates = <80000000>;
> +	status = "okay";
> +};
> +
> +&usdhc1 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc1>;
> +	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> +	bus-width = <8>;
> +	non-removable;
> +	status = "okay";
> +};
> +
> +&pgc_vpu {

This one is out of alphabetical order.

Shawn

> +	power-supply = <&sw1c_reg>;
> +};
> +
> +&wdog1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_wdog>;
> +	fsl,ext-reset-output;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_fec1: fec1grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC		0x3
> +			MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO	0x23
> +			MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x1f
> +			MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x1f
> +			MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x1f
> +			MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x1f
> +			MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x91
> +			MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x91
> +			MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x91
> +			MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x91
> +			MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f
> +			MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91
> +			MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
> +			MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
> +			MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x19
> +		>;
> +	};
> +
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL			0x4000007f
> +			MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA			0x4000007f
> +		>;
> +	};
> +
> +	pinctrl_pcie0: pcie0grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B	0x74
> +			MX8MQ_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5	0x16
> +			MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21	0x16
> +		>;
> +	};
> +
> +	pinctrl_qspi: qspigrp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK	0x82
> +			MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B	0x82
> +			MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0	0x82
> +			MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1	0x82
> +			MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2	0x82
> +			MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3	0x82
> +
> +		>;
> +	};
> +
> +	pinctrl_uart1: uart1grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x49
> +			MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX		0x49
> +			MX8MQ_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
> +		>;
> +	};
> +
> +	pinctrl_uart4: uart4grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_UART4_TXD_UART4_DCE_TX		0x49
> +			MX8MQ_IOMUXC_UART4_RXD_UART4_DCE_RX		0x49
> +			MX8MQ_IOMUXC_SAI3_TXD_GPIO5_IO1			0x19
> +		>;
> +	};
> +
> +	pinctrl_usdhc1: usdhc1grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
> +			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc3
> +			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc3
> +			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc3
> +			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc3
> +			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc3
> +			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc3
> +			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc3
> +			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc3
> +			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc3
> +			MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x83
> +			MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x8d
> +			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xcd
> +			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xcd
> +			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xcd
> +			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xcd
> +			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xcd
> +			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xcd
> +			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xcd
> +			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xcd
> +			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xcd
> +			MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x8d
> +			MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x9f
> +			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xdf
> +			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xdf
> +			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xdf
> +			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xdf
> +			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xdf
> +			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xdf
> +			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xdf
> +			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xdf
> +			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xdf
> +			MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x9f
> +			MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
> +		>;
> +	};
> +
> +	pinctrl_wdog: wdoggrp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
> +		>;
> +	};
> +};
> -- 
> 2.20.1
> 

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel