From: Neil Armstrong <narmstrong@baylibre•com>
To: khilman@baylibre•com
Cc: linux-amlogic@lists•infradead.org, linux-kernel@vger•kernel.org,
linux-arm-kernel@lists•infradead.org,
Neil Armstrong <narmstrong@baylibre•com>
Subject: [PATCH 6/6] arm64: dts: add support for SM1 based SEI Robotics SEI610
Date: Tue, 20 Aug 2019 16:40:52 +0200 [thread overview]
Message-ID: <20190820144052.18269-7-narmstrong@baylibre.com> (raw)
In-Reply-To: <20190820144052.18269-1-narmstrong@baylibre.com>
Add support for the Amlogic SM1 Based SEI610 board.
The SM1 SoC is a derivative of the G12A SoC Family with :
- Cortex-A55 core instead of A53
- more power domains, including USB & PCIe
- a neural network co-processor (NNA)
- a CSI input and image processor
- some changes in the audio complex, thus not yet enabled
The SEI610 board is a derivative of the SEI510 board with :
- removed ADC based touch button, replaced with 3x GPIO buttons
- physical switch disabling on-board MICs
- USB-C port for USB 2.0 OTG
- On-board FTDI USB2SERIAL port for Linux console
Audio, Display and USB support will be added later when support of the
corresponding power domains will be added, for now they are kept disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre•com>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-sm1-sei610.dts | 300 ++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-sm1.dtsi | 68 ++++
3 files changed, 369 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index ae5e8d0c08da..edbf128e7707 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -34,3 +34,4 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q201.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-rbox-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
new file mode 100644
index 000000000000..12dab0ba2f26
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+ compatible = "seirobotics,sei610", "amlogic,sm1";
+ model = "SEI Robotics SEI610";
+
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+
+ key1 {
+ label = "A";
+ linux,code = <BTN_0>;
+ gpios = <&gpio GPIOH_6 GPIO_ACTIVE_LOW>;
+ };
+
+ key2 {
+ label = "B";
+ linux,code = <BTN_1>;
+ gpios = <&gpio GPIOH_7 GPIO_ACTIVE_LOW>;
+ };
+
+ key3 {
+ label = "C";
+ linux,code = <BTN_2>;
+ gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ bluetooth {
+ label = "sei610:blue:bt";
+ gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ default-state = "off";
+ };
+ };
+
+ pwmleds {
+ compatible = "pwm-leds";
+
+ power {
+ label = "sei610:red:power";
+ pwms = <&pwm_AO_ab 0 30518 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "default-on";
+ active-low;
+ };
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ ao_5v: regulator-ao_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "AO_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_in>;
+ regulator-always-on;
+ };
+
+ dc_in: regulator-dc_in {
+ compatible = "regulator-fixed";
+ regulator-name = "DC_IN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ emmc_1v8: regulator-emmc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "EMMC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&dc_in>;
+ regulator-always-on;
+ };
+
+ /* Used by Tuner, RGB Led & IR Emitter LED array */
+ vddao_3v3_t: regultor-vddao_3v3_t {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3_T";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+ enable-active-low;
+ regulator-always-on;
+ };
+
+ vddio_ao1v8: regulator-vddio_ao1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ reserved-memory {
+ /* TEE Reserved Memory */
+ bl32_reserved: bl32@5000000 {
+ reg = <0x0 0x05300000 0x0 0x2000000>;
+ no-map;
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+ðmac {
+ status = "okay";
+ phy-handle = <&internal_ephy>;
+ phy-mode = "rmii";
+};
+
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_AO_ab {
+ status = "okay";
+ pinctrl-0 = <&pwm_ao_a_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao1v8>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr50;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_ao1v8>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&emmc_1v8>;
+};
+
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+ max-speed = <2000000>;
+ clocks = <&wifi32k>;
+ clock-names = "lpo";
+ vbat-supply = <&vddao_3v3>;
+ vddio-supply = <&vddio_ao1v8>;
+ };
+};
+
+/* Exposed via the on-board USB to Serial FT232RL IC */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
new file mode 100644
index 000000000000..e902d4f9165f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre•com>
+ */
+
+#include "meson-g12-common.dtsi"
+
+/ {
+ compatible = "amlogic,sm1";
+
+ cpus {
+ #address-cells = <0x2>;
+ #size-cells = <0x0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0 0x2>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0 0x3>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache0 {
+ compatible = "cache";
+ };
+ };
+};
+
+&cecb_AO {
+ compatible = "amlogic,meson-sm1-ao-cec";
+};
+
+&clk_msr {
+ compatible = "amlogic,meson-sm1-clk-measure";
+};
+
+&pwrc_vpu {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
--
2.22.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists•infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-08-20 14:43 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-20 14:40 [PATCH 0/6] arm64: Add support for Amlogic SM1 SoC Family Neil Armstrong
2019-08-20 14:40 ` [PATCH 1/6] soc: amlogic: meson-gx-socinfo: Add SM1 and S905X3 IDs Neil Armstrong
2019-08-20 14:40 ` [PATCH 2/6] dt-bindings: soc: amlogic: clk-measure: Add SM1 compatible Neil Armstrong
2019-08-20 14:40 ` [PATCH 3/6] soc: amlogic: clk-measure: Add support for SM1 Neil Armstrong
2019-08-20 14:40 ` [PATCH 4/6] dt-bindings: arm: amlogic: add SM1 bindings Neil Armstrong
2019-08-20 16:15 ` Rob Herring
2019-08-20 14:40 ` [PATCH 5/6] dt-bindings: arm: amlogic: add SEI Robotics SEI610 bindings Neil Armstrong
2019-08-20 16:16 ` Rob Herring
2019-08-20 14:40 ` Neil Armstrong [this message]
2019-08-20 20:11 ` [PATCH 6/6] arm64: dts: add support for SM1 based SEI Robotics SEI610 Martin Blumenstingl
2019-08-20 20:32 ` Kevin Hilman
2019-08-20 19:25 ` [PATCH 0/6] arm64: Add support for Amlogic SM1 SoC Family Kevin Hilman
2019-08-20 23:06 ` Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190820144052.18269-7-narmstrong@baylibre.com \
--to=narmstrong@baylibre$(echo .)com \
--cc=khilman@baylibre$(echo .)com \
--cc=linux-amlogic@lists$(echo .)infradead.org \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
--cc=linux-kernel@vger$(echo .)kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox