Subject: [PATCH 1/5] dt-bindings: i2c: aspeed: add buffer and DMA mode transfer support

From: Jae Hyun Yoo <[email-masked]>
Date: Mon, 7 Oct 2019 16:13:09 -0700

Append bindings to support buffer mode and DMA mode transfer.

Signed-off-by: Jae Hyun Yoo <[email-masked]>
---
 .../devicetree/bindings/i2c/i2c-aspeed.txt    | 67 +++++++++++++++++--
 1 file changed, 60 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
index 8fbd8633a387..e40dcc108307 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
@@ -3,7 +3,10 @@ Device tree configuration for the I2C busses on the AST24XX and AST25XX SoCs.
 Required Properties:
 - #address-cells	: should be 1
 - #size-cells		: should be 0
-- reg			: address offset and range of bus
+- reg			: Address offset and range of bus registers.
+			  An additional SRAM buffer address offset and range is
+			  optional in case of enabling I2C dedicated SRAM for
+			  buffer mode transfer support.
 - compatible		: should be "aspeed,ast2400-i2c-bus"
 			  or "aspeed,ast2500-i2c-bus"
 - clocks		: root clock of bus, should reference the APB
@@ -16,6 +19,18 @@ Optional Properties:
 - bus-frequency	: frequency of the bus clock in Hz defaults to 100 kHz when not
 		  specified
 - multi-master	: states that there is another master active on this bus.
+- aspeed,dma-buf-size	: size of DMA buffer (from 2 to 4095 in case of AST2500
+			  or later versions).
+			  Only AST2500 and later versions support DMA mode
+			  under some limitations:
+			  I2C is sharing the DMA H/W with UHCI host controller
+			  and MCTP controller. Since those controllers operate
+			  with DMA mode only, I2C has to use buffer mode or byte
+			  mode instead if one of those controllers is enabled.
+			  Also make sure that if SD/eMMC or Port80 snoop uses
+			  DMA mode instead of PIO or FIFO respectively, I2C
+			  can't use DMA mode. If both DMA and buffer modes are
+			  enabled, DMA mode will be selected.
 
 Example:
 
@@ -25,12 +40,21 @@ i2c {
 	#size-cells = <1>;
 	ranges = <0 0x1e78a000 0x1000>;
 
-	i2c_ic: interrupt-controller@0 {
-		#interrupt-cells = <1>;
-		compatible = "aspeed,ast2400-i2c-ic";
+	i2c_gr: i2c-global-regs@0 {
+		compatible = "aspeed,ast2500-i2c-gr", "syscon";
 		reg = <0x0 0x40>;
-		interrupts = <12>;
-		interrupt-controller;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x40>;
+
+		i2c_ic: interrupt-controller@0 {
+			#interrupt-cells = <1>;
+			compatible = "aspeed,ast2500-i2c-ic";
+			reg = <0x0 0x4>;
+			interrupts = <12>;
+			interrupt-controller;
+		};
 	};
 
 	i2c0: i2c-bus@40 {
@@ -38,11 +62,40 @@ i2c {
 		#size-cells = <0>;
 		#interrupt-cells = <1>;
 		reg = <0x40 0x40>;
-		compatible = "aspeed,ast2400-i2c-bus";
+		compatible = "aspeed,ast2500-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB>;
 		resets = <&syscon ASPEED_RESET_I2C>;
 		bus-frequency = <100000>;
 		interrupts = <0>;
 		interrupt-parent = <&i2c_ic>;
 	};
+
+	/* buffer mode transfer enabled */
+	i2c1: i2c-bus@80 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0x80 0x40>, <0x210 0x10>;
+		compatible = "aspeed,ast2500-i2c-bus";
+		clocks = <&syscon ASPEED_CLK_APB>;
+		resets = <&syscon ASPEED_RESET_I2C>;
+		bus-frequency = <100000>;
+		interrupts = <1>;
+		interrupt-parent = <&i2c_ic>;
+	};
+
+	/* DMA mode transfer enabled */
+	i2c2: i2c-bus@c0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0xc0 0x40>;
+		aspeed,dma-buf-size = <4095>;
+		compatible = "aspeed,ast2500-i2c-bus";
+		clocks = <&syscon ASPEED_CLK_APB>;
+		resets = <&syscon ASPEED_RESET_I2C>;
+		bus-frequency = <100000>;
+		interrupts = <2>;
+		interrupt-parent = <&i2c_ic>;
+	};
 };
-- 
2.23.0

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel