Subject: [PATCH v2 06/13] dt-bindings: Add Broadcom STB USB PHY binding document

From: Al Cooper <[email-masked]>
Date: Fri, 15 Nov 2019 13:42:16 -0500

Add support for bcm7216 and bcm7211

Signed-off-by: Al Cooper <[email-masked]>
---
 .../bindings/phy/brcm,brcmstb-usb-phy.txt     | 69 +++++++++++++++----
 1 file changed, 56 insertions(+), 13 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
index 24a0d06acd1d..698aacbdcfc4 100644
--- a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
+++ b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
@@ -1,30 +1,49 @@
 Broadcom STB USB PHY
 
 Required properties:
- - compatible: brcm,brcmstb-usb-phy
- - reg: two offset and length pairs.
-	The first pair specifies a manditory set of memory mapped
-	registers used for general control of the PHY.
-	The second pair specifies optional registers used by some of
-	the SoCs that support USB 3.x
- - #phy-cells: Shall be 1 as it expects one argument for setting
-	       the type of the PHY. Possible values are:
-	       - PHY_TYPE_USB2 for USB1.1/2.0 PHY
-	       - PHY_TYPE_USB3 for USB3.x PHY
+- compatible: should be one of
+	"brcm,brcmstb-usb-phy"
+	"brcm,bcm7216-usb-phy"
+	"brcm,bcm7211-usb-phy"
+
+- reg and reg-names properties requirements are specific to the
+  compatible string.
+  "brcm,brcmstb-usb-phy":
+    - reg: 1 or 2 offset and length pairs. One for the base CTRL registers
+           and an optional pair for systems with USB 3.x support
+    - reg-names: not specified
+  "brcm,bcm7216-usb-phy":
+    - reg: 3 offset and length pairs for CTRL, XHCI_EC and XHCI_GBL
+           registers
+    - reg-names: "ctrl", "xhci_ec", "xhci_gbl"
+  "brcm,bcm7211-usb-phy":
+    - reg: 5 offset and length pairs for CTRL, XHCI_EC, XHCI_GBL,
+           USB_PHY and USB_MDIO registers and an optional pair
+	   for the BDC registers
+    - reg-names: "ctrl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio", "bdc_ec"
+
+- #phy-cells: Shall be 1 as it expects one argument for setting
+	      the type of the PHY. Possible values are:
+	      - PHY_TYPE_USB2 for USB1.1/2.0 PHY
+	      - PHY_TYPE_USB3 for USB3.x PHY
 
 Optional Properties:
 - clocks : clock phandles.
 - clock-names: String, clock name.
+- interrupts: wakeup interrupt
+- interrupt-names: "wakeup"
 - brcm,ipp: Boolean, Invert Port Power.
   Possible values are: 0 (Don't invert), 1 (Invert)
 - brcm,ioc: Boolean, Invert Over Current detection.
   Possible values are: 0 (Don't invert), 1 (Invert)
-NOTE: one or both of the following two properties must be set
-- brcm,has-xhci: Boolean indicating the phy has an XHCI phy.
-- brcm,has-eohci: Boolean indicating the phy has an EHCI/OHCI phy.
 - dr_mode: String, PHY Device mode.
   Possible values are: "host", "peripheral ", "drd" or "typec-pd"
   If this property is not defined, the phy will default to "host" mode.
+- brcm,syscon-piarbctl: phandle to syscon for handling config registers
+NOTE: one or both of the following two properties must be set
+- brcm,has-xhci: Boolean indicating the phy has an XHCI phy.
+- brcm,has-eohci: Boolean indicating the phy has an EHCI/OHCI phy.
+
 
 Example:
 
@@ -41,3 +60,27 @@ usbphy_0: usb-phy@f0470200 {
 	clocks = <&usb20>, <&usb30>;
 	clock-names = "sw_usb", "sw_usb3";
 };
+
+usb-phy@29f0200 {
+	reg = <0x29f0200 0x200>,
+		<0x29c0880 0x30>,
+		<0x29cc100 0x534>,
+		<0x2808000 0x24>,
+		<0x2980080 0x8>;
+	reg-names = "ctrl",
+		"xhci_ec",
+		"xhci_gbl",
+		"usb_phy",
+		"usb_mdio";
+	brcm,ioc = <0x0>;
+	brcm,ipp = <0x0>;
+	compatible = "brcm,bcm7211-usb-phy";
+	interrupts = <0x30>;
+	interrupt-parent = <&vpu_intr1_nosec_intc>;
+	interrupt-names = "wake";
+	#phy-cells = <0x1>;
+	brcm,has-xhci;
+	syscon-piarbctl = <&syscon_piarbctl>;
+	clocks = <&scmi_clk 256>;
+	clock-names = "sw_usb";
+};
-- 
2.17.1

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel