Subject: Re: [PATCH v8 0/7] add thermal sensor driver for A64, A83T, H3, H5, H6, R40

From: Corentin Labbe <[email-masked]>
Date: Tue, 24 Dec 2019 14:11:55 +0100

On Thu, Dec 19, 2019 at 09:28:16AM -0800, Vasily Khoruzhick wrote:
> This patchset adds driver for thermal sensor in A64, A83T, H3, H5,
> H6 and R40 SoCs.
> 
> v8:
> 	- [vasily] Address more Maxime's comments for dt-schema
> 	- [vasily] Add myself to MAINTAINERS for the driver and schema
> 	- [vasily] Round calibration data size to word boundary for H6 and A64
> 	- [vasily] Change offset for A64 since it reports too low temp otherwise.
> 	           Likely conversion formula in user manual is not correct.
> 
> v7:
> 	- [vasily] Address Maxime's comments for dt-schema
> 	- [vasily] Move common part of H3 and H5 dts into sunxi-h3-h5.dtsi
> 	- [vasily] Add Maxime's a-b to the driver patch 
> 
> v6:
> 	- [ondrej, vasily] Squash all driver related changes into a
> 			   single patch
> 	- [ondrej] Rename calib -> calibration
> 	- [ondrej] Fix thermal zone registration check
> 	- [ondrej] Lower rate of sensor data interrupts to 4/sec/sensor
> 	- [ondrej] Rework scale/offset values, H6 calibration
> 	- [ondrej] Explicitly set mod clock to 24 MHz
> 	- [ondrej] Set undocumented bits in CTRL0 for H6
> 	- [ondrej] Add support for A83T
> 	- [ondrej] Add dts changes for A83T, H3, H5, H6
> 	- [vasily] Add dts changes for A64
> 	- [vasily] Address Maxime's comments for YAML scheme
> 	- [vasily] Make .calc_temp callback mandatory
> 	- [vasily] Set .max_register in regmap config, so regs can be
> 		   inspected using debugfs
> 
> Ondrej Jirman (4):
>   ARM: dts: sun8i-a83t: Add thermal sensor and thermal zones
>   ARM: dts: sun8i-h3: Add thermal sensor and thermal zones
>   arm64: dts: allwinner: h5: Add thermal sensor and thermal zones
>   arm64: dts: allwinner: h6: Add thermal sensor and thermal zones
> 
> Vasily Khoruzhick (1):
>   arm64: dts: allwinner: a64: Add thermal sensors and thermal zones
> 
> Yangtao Li (2):
>   thermal: sun8i: add thermal driver for H6/H5/H3/A64/A83T/R40
>   dt-bindings: thermal: add YAML schema for sun8i-thermal driver
>     bindings
> 
>  .../thermal/allwinner,sun8i-a83t-ths.yaml     | 160 +++++
>  MAINTAINERS                                   |   8 +
>  arch/arm/boot/dts/sun8i-a83t.dtsi             |  36 +
>  arch/arm/boot/dts/sun8i-h3.dtsi               |  20 +
>  arch/arm/boot/dts/sunxi-h3-h5.dtsi            |   6 +
>  arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi |  42 ++
>  arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi  |  26 +
>  arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  |  33 +
>  drivers/thermal/Kconfig                       |  14 +
>  drivers/thermal/Makefile                      |   1 +
>  drivers/thermal/sun8i_thermal.c               | 639 ++++++++++++++++++
>  11 files changed, 985 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
>  create mode 100644 drivers/thermal/sun8i_thermal.c
> 
> -- 
> 2.24.1
> 

Hello

Thanks for your work.

Tested-by: Corentin Labbe <[email-masked]>
Tested-on: sun50i-h6-pine-h64-model-b
Tested-on: sun50i-h6-pine-h64
Tested-on: sun8i-a83t-bananapi-m3
Tested-on: sun8i-h2-plus-orangepi-zero
Tested-on: sun8i-h2-plus-orangepi-r1
Tested-on: sun8i-h2-plus-libretech-all-h3-cc
Tested-on: sun8i-h3-libretech-all-h3-cc
Tested-on: sun50i-h5-libretech-all-h3-cc
Tested-on: sun50i-a64-pine64-plus

Note that your patch serie support R40 but you do not have any R40 DT patch.
If you need testing, do not hesitate to ask.

Regards

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel