Subject: Re: [PATCH 6/6] arm64: allwinner: a64: enable LCD-related hardware for Pinebook

From: Laurent Pinchart <[email-masked]>
Date: Thu, 20 Feb 2020 16:17:25 +0200

Hi Vasily,

Thank you for the patch.

On Thu, Feb 20, 2020 at 12:35:08AM -0800, Vasily Khoruzhick wrote:
> From: Icenowy Zheng <[email-masked]>
> 
> Pinebook has an ANX6345 bridge connected to the RGB666 LCD output and
> eDP panel input. The bridge is controlled via I2C that's connected to
> R_I2C bus.
> 
> Enable all this hardware in device tree.
> 
> Signed-off-by: Icenowy Zheng <[email-masked]>
> Signed-off-by: Vasily Khoruzhick <[email-masked]>
> ---
>  .../dts/allwinner/sun50i-a64-pinebook.dts     | 69 ++++++++++++++++++-
>  1 file changed, 68 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
> index c06c540e6c08..f5633f550d8a 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
> @@ -48,6 +48,18 @@ lid_switch {
>  		};
>  	};
>  
> +	panel_edp: panel-edp {
> +		compatible = "neweast,wjfh116008a";
> +		backlight = <&backlight>;
> +		power-supply = <&reg_dc1sw>;
> +
> +		port {
> +			panel_edp_in: endpoint {
> +				remote-endpoint = <&anx6345_out_edp>;
> +			};
> +		};
> +	};
> +
>  	reg_vbklt: vbklt {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vbklt";
> @@ -109,6 +121,10 @@ &dai {
>  	status = "okay";
>  };
>  
> +&de {
> +	status = "okay";
> +};
> +
>  &ehci0 {
>  	phys = <&usbphy 0>;
>  	phy-names = "usb";
> @@ -119,6 +135,10 @@ &ehci1 {
>  	status = "okay";
>  };
>  
> +&mixer0 {
> +	status = "okay";
> +};
> +
>  &mmc0 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&mmc0_pins>;
> @@ -177,12 +197,45 @@ &pwm {
>  	status = "okay";
>  };
>  
> -/* The ANX6345 eDP-bridge is on r_i2c */
>  &r_i2c {
>  	clock-frequency = <100000>;
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&r_i2c_pl89_pins>;
>  	status = "okay";
> +
> +	anx6345: anx6345@38 {
> +		compatible = "analogix,anx6345";
> +		reg = <0x38>;
> +		reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */
> +		dvdd25-supply = <&reg_dldo2>;
> +		dvdd12-supply = <&reg_fldo1>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			anx6345_in: port@0 {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				reg = <0>;
> +				anx6345_in_tcon0: endpoint@0 {
> +					reg = <0>;
> +					remote-endpoint = <&tcon0_out_anx6345>;
> +				};

As there's a single endpoint, you can drop the reg property, the @0
suffix, and the #address-cells and #size-cells property in the port@0
node (but not in the ports node).

> +			};
> +
> +			anx6345_out: port@1 {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				reg = <1>;
> +
> +				anx6345_out_edp: endpoint@0 {
> +					reg = <0>;
> +					remote-endpoint = <&panel_edp_in>;
> +				};

Same here.

Reviewed-by: Laurent Pinchart <[email-masked]>

> +			};
> +		};
> +	};
>  };
>  
>  &r_pio {
> @@ -357,6 +410,20 @@ &sound {
>  			"MIC2", "Internal Microphone Right";
>  };
>  
> +&tcon0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&lcd_rgb666_pins>;
> +
> +	status = "okay";
> +};
> +
> +&tcon0_out {
> +	tcon0_out_anx6345: endpoint@0 {
> +		reg = <0>;
> +		remote-endpoint = <&anx6345_in_tcon0>;
> +	};
> +};
> +
>  &uart0 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&uart0_pb_pins>;

-- 
Regards,

Laurent Pinchart

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel