Subject: Re: [PATCH] ARM: at91: Add GARDENA smart Gateway AT91SAM board

From: Alexandre Belloni <[email-masked]>
Date: Mon, 17 Aug 2020 12:21:36 +0200

Hello,

Thank you for this submission.

On 10/08/2020 19:19:19+0200, Reto Schneider wrote:
> From: Reto Schneider <[email-masked]>
> 
> This patch adds support for the GARDENA smart Gateway, which is based on
> the Atmel AT91SAM9G25. It is equipped with 128 MiB of DDR2 RAM and
> 256 MiB NAND storage.
> 
> Please note that this gateway is not actually based on a AT91SAM9x5 EK
> board, but is close enough to allow its DT to be used.
> 
> Co-developed-by: Stefan Roese <[email-masked]>
> Signed-off-by: Stefan Roese <[email-masked]>
> Co-developed-by: Michael Zimmermann <[email-masked]>
> Signed-off-by: Michael Zimmermann <[email-masked]>
> Signed-off-by: Reto Schneider <[email-masked]>
> ---
>  arch/arm/boot/dts/Makefile                    |   1 +
>  .../dts/at91sam9g25-gardena-smart-gateway.dts | 186 ++++++++++++++++++
>  2 files changed, 187 insertions(+)
>  create mode 100644 arch/arm/boot/dts/at91sam9g25-gardena-smart-gateway.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 4572db3fa5ae..d38d256f59fa 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -44,6 +44,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
>  	at91-wb45n.dtb \
>  	at91sam9g15ek.dtb \
>  	at91sam9g25ek.dtb \
> +	at91sam9g25-gardena-smart-gateway.dtb \
>  	at91sam9g35ek.dtb \
>  	at91sam9x25ek.dtb \
>  	at91sam9x35ek.dtb
> diff --git a/arch/arm/boot/dts/at91sam9g25-gardena-smart-gateway.dts b/arch/arm/boot/dts/at91sam9g25-gardena-smart-gateway.dts
> new file mode 100644
> index 000000000000..19b0f67a7af6
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91sam9g25-gardena-smart-gateway.dts
> @@ -0,0 +1,186 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Device Tree file for the GARDENA smart Gateway (AT91SAM)
> + *
> + *  Copyright (C) 2020 GARDENA GmbH
> + */
> +
> +/dts-v1/;
> +
> +#include "at91sam9g25.dtsi"
> +#include "at91sam9x5ek.dtsi"
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "GARDENA smart Gateway (AT91SAM)";
> +	compatible = "gardena,smart-gateway-at91sam", "atmel,at91sam9g25", "atmel,at91sam9x5", "atmel,at91sam9";

You should document the vendor string. And ideally,
gardena,smart-gateway-at91sam should be documented in
Documentation/devicetree/bindings/arm/atmel-at91.yaml

> +
> +	aliases {
> +		serial1 = &usart3;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";

This is already in at91sam9x5ek.dtsi

> +	};
> +
> +	memory {
> +		reg = <0x20000000 0x8000000>;

This is already in at91sam9x5cm.dtsi, included fromat91sam9x5ek.dtsi

> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		user_btn1 {
> +			label = "USER_BTN1";
> +			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_PROG1>;
> +		};
> +	};
> +
> +	1wire_cm {
> +		status = "disabled";
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		power_blue {
> +			label = "smartgw:power:blue";
> +			gpios = <&pioC 21 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		power_green {
> +			label = "smartgw:power:green";
> +			gpios = <&pioC 20 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +
> +		power_red {
> +			label = "smartgw:power:red";
> +			gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		radio_blue {
> +			label = "smartgw:radio:blue";
> +			gpios = <&pioC 18 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		radio_green {
> +			label = "smartgw:radio:green";
> +			gpios = <&pioC 17 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		radio_red {
> +			label = "smartgw:radio:red";
> +			gpios = <&pioC 16 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		internet_blue {
> +			label = "smartgw:internet:blue";
> +			gpios = <&pioC 15 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		internet_green {
> +			label = "smartgw:internet:green";
> +			gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		internet_red {
> +			label = "smartgw:internet:red";
> +			gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		heartbeat {
> +			label = "smartgw:heartbeat";
> +			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +		pb18 {
> +			status = "disabled";
> +		};
> +
> +		pd21 {
> +			status = "disabled";
> +		};
> +	};
> +};
> +
> +&dbgu {
> +	status = "okay";
> +};

This is already in at91sam9x5ek.dtsi and is duplicated below

> +
> +&macb0 {
> +	phy-mode = "rmii";
> +	status = "okay";
> +};
> +
> +&nand_controller {
> +	status = "okay";

This is already in at91sam9x5cm.dtsi

> +};
> +
> +&usb0 {
> +	status = "okay";
> +	num-ports = <3>;

This is already in at91sam9x5ek.dtsi

> +};
> +
> +&usb1 {
> +	status = "okay";
This is already in at91sam9x5ek.dtsi
> +};
> +
> +&usart0 {
> +	status = "disabled";
> +};
> +
> +&usart2 {
> +	status = "disabled";
> +};
> +
> +&dbgu {
> +	status = "okay";
> +};
> +
> +&usart3 {
> +	status = "okay";
> +
> +	pinctrl-0 = <&pinctrl_usart3
> +		     &pinctrl_usart3_rts
> +		     &pinctrl_usart3_cts
> +		    >;
> +};
> +
> +&watchdog {
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	status = "disabled";
> +};
> +
> +&mmc1 {
> +	status = "disabled";
> +};
> +
> +&spi0 {
> +	status = "disabled";
> +};
> +
> +&i2c0 {
> +	status = "disabled";
> +};
> +
> +&adc0 {
> +	status = "disabled";
> +};
> +
> +&ssc0 {
> +	status = "disabled";
> +};

Overall, I'm not convinced it is a good idea to start from
at91sam9x5ek.dtsi as it makes you dtb bigger than necessary but if you
want it that way, I'm fine with that.

-- 
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel