Subject: Re: [PATCH v3 2/6] ASoC: audio-graph-card: Add plls and sysclks DT bindings

From: Rob Herring <[email-masked]>
Date: Mon, 21 Dec 2020 15:34:13 -0700

On Thu, Dec 17, 2020 at 03:41:38PM +0000, Richard Fitzgerald wrote:
> The audio-graph-card driver has bindings for configuring the clocking
> for DAIs within a component, but is missing bindings for setting
> up the PLLs and sysclks of the component.
> 
> This patch adds the two new bindings 'plls' and 'sysclks' so that the
> audio-graph-driver can fully configure the component clocking.
> 
> Signed-off-by: Richard Fitzgerald <[email-masked]>
> ---
>  .../bindings/sound/audio-graph-card.txt       | 72 +++++++++++++++++++
>  1 file changed, 72 insertions(+)

This is a schema now in master.

> 
> diff --git a/Documentation/devicetree/bindings/sound/audio-graph-card.txt b/Documentation/devicetree/bindings/sound/audio-graph-card.txt
> index d5f6919a2d69..30405e64cfbb 100644
> --- a/Documentation/devicetree/bindings/sound/audio-graph-card.txt
> +++ b/Documentation/devicetree/bindings/sound/audio-graph-card.txt
> @@ -32,6 +32,40 @@ Required properties:
>  Optional properties:
>  - pa-gpios: GPIO used to control external amplifier.
>  
> +- plls: A list of component pll settings. There are 4 cells per PLL setting:
> +	- phandle to the node of the codec or cpu component,
> +	- component PLL id,
> +	- component clock source id,
> +	- frequency (in Hz) of the PLL output clock.
> +
> +	The PLL id and clock source id are specific to the particular component
> +	so see the relevant component driver for the ids. Typically the
> +	clock source id indicates the pin the source clock is connected to.
> +
> +	The same phandle can appear in multiple entries so that several plls
> +	can be set in the same component.
> +
> +- plls-clocks: A list of clock names giving the source clock for each setting
> +	in the plls property.
> +
> +- sysclks: A list of component sysclk settings.  There are 4 cells per sysclk
> +	setting:
> +	- phandle to the node of the codec or cpu component,
> +	- component sysclk id,
> +	- component clock source id,
> +	- direction of the clock: 0 if the clock is an input to the component,
> +	  1 if it is an output.
> +
> +	The sysclk id and clock source id are specific to the particular
> +	component so see the relevant component driver for the ids. Typically
> +	the clock source id indicates the pin the source clock is connected to.
> +
> +	The same phandle can appear in multiple entries so that several sysclks
> +	can be set in the same component.
> +
> +- sysclks-clocks: A list of clock names giving the source clock for each setting
> +	in the sysclks property.
> +
>  -----------------------
>  Example: Single DAI case
>  -----------------------
> @@ -335,3 +369,41 @@ Example: Multi DAI with DPCM
>  			};
>  		};
>  	};
> +
> +-----------------------
> +Example: Set component sysclks and PLLs
> +-----------------------
> +
> +	sound {
> +		compatible = "audio-graph-card";
> +
> +		clocks = <&audioclk>, <&pll1>;
> +		clock-names = "audioclk", "pll1";
> +
> +		plls = <&cs47l15 MADERA_FLL1_REFCLK MADERA_FLL_SRC_MCLK1 98304000>;
> +		plls-clocks = "audioclk";
> +
> +		sysclks = <&cs47l15 MADERA_CLK_SYSCLK_1 MADERA_CLK_SRC_FLL1 0>;
> +		sysclks-clocks = "pll1";
> +
> +		dais = <&cpu_i2s_port>;
> +
> +		pll1: pll1 {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <98304000>;
> +		};
> +	};
> +
> +	cs47l15: codec@0 {
> +		...
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			cs47l15_aif1_port: port@0 {
> +				reg = <0>;
> +				cs47l15_aif1: endpoint {
> +					remote-endpoint = <&cpu_i2s_endpoint>;
> +				};
> +			};
> +	};
> -- 
> 2.20.1
> 

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel