Subject: [PATCH v5 2/7] ARM: davinci, cp_intc: Add OF support for TI interrupt controller

From: [email-masked] (Sekhar Nori)
Date: Wed, 4 Jul 2012 00:39:20 +0530

Hi Heiko,

On 5/30/2012 3:48 PM, Heiko Schocher wrote:
> Add a function to initialize the Common Platform Interrupt Controller
> (cp_intc) from TI used on OMAP-L1x SoCs using a device tree node.
> 
> Signed-off-by: Heiko Schocher <[email-masked]>
> Cc: davinci-linux-open-source at linux.davincidsp.com
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: devicetree-discuss at lists.ozlabs.org
> Cc: Grant Likely <[email-masked]>
> Cc: Sekhar Nori <[email-masked]>
> Cc: Wolfgang Denk <[email-masked]>
> Cc: Sergei Shtylyov <[email-masked]>
> 
> ---
> - changes for v4
>   - split patch in 2 patches, one for irq_domain adaption
>     one for DT enhancement, as Nori Sekhar suggested.
>   - add comment from Grant Likely for the DT part:
>     remove if/else clause, not needed.
>     Make use of DT runtime configurable
> 
> - changes for v5:
>   add comments from Sergei Shtylyov:
>   - s/intc/cp_intc in commit subject
>   add comments from Grant Likely:
>   - rename compatible" prop to "ti,cp-intc"
> 
>  .../devicetree/bindings/arm/davinci/intc.txt       |   27 ++++++++++++++++++++
>  arch/arm/mach-davinci/cp_intc.c                    |   24 ++++++++++++++++-
>  2 files changed, 49 insertions(+), 2 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/arm/davinci/intc.txt
> 
> diff --git a/Documentation/devicetree/bindings/arm/davinci/intc.txt b/Documentation/devicetree/bindings/arm/davinci/intc.txt
> new file mode 100644
> index 0000000..597e8a0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/davinci/intc.txt

I think this file is better named cp-intc.txt since there is also an
intc (a different IP) used on DaVinci platforms.

> @@ -0,0 +1,27 @@
> +* TI Common Platform Interrupt Controller
> +
> +Common Platform Interrupt Controller (cp_intc) is used on
> +OMAP-L1x SoCs and can support several configurable number
> +of interrupts.
> +
> +Main node required properties:
> +
> +- compatible : should be:
> +	"ti,cp-intc"
> +- interrupt-controller : Identifies the node as an interrupt controller
> +- #interrupt-cells : Specifies the number of cells needed to encode an
> +  interrupt source. The type shall be a <u32> and the value shall be 1.
> +
> +  The cell contains the interrupt number in the range [0-128].
> +- ti,intc-size: Number of interrupts handled by the interrupt controller.
> +- reg: physical base address and size of the intc registers map.
> +
> +Example:
> +
> +	intc: interrupt-controller at 1 {
> +		compatible = "ti,cp-intc";
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		ti,intc-size = <101>;
> +		reg = <0xfffee000 0x2000>;
> +	};
> diff --git a/arch/arm/mach-davinci/cp_intc.c b/arch/arm/mach-davinci/cp_intc.c
> index 45d5256..d1bef55 100644
> --- a/arch/arm/mach-davinci/cp_intc.c
> +++ b/arch/arm/mach-davinci/cp_intc.c
> @@ -14,6 +14,9 @@
>  #include <linux/irq.h>
>  #include <linux/irqdomain.h>
>  #include <linux/io.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_irq.h>
>  
>  #include <mach/common.h>
>  #include <mach/cp_intc.h>
> @@ -119,7 +122,7 @@ static const struct irq_domain_ops cp_intc_host_ops = {
>  	.xlate = irq_domain_xlate_onetwocell,
>  };
>  
> -int __init __cp_intc_init(struct device_node *node)
> +int __init __cp_intc_init(struct device_node *node, struct device_node *parent)
>  {
>  	u32 num_irq		= davinci_soc_info.intc_irq_num;
>  	u8 *irq_prio		= davinci_soc_info.intc_irq_prios;
> @@ -129,6 +132,15 @@ int __init __cp_intc_init(struct device_node *node)
>  
>  	davinci_intc_type = DAVINCI_INTC_TYPE_CP_INTC;

>  	davinci_intc_base = ioremap(davinci_soc_info.intc_base, SZ_8K);

This line needs to be dropped because you are doing an ioremap again
down below.

> +	if (node) {
> +		davinci_intc_base = of_iomap(node, 0);
> +		if (of_property_read_u32(node, "ti,intc-size", &num_irq))
> +			pr_warn("unable to get intc-size, default to %d\n",
> +				num_irq);
> +	} else {
> +		davinci_intc_base = ioremap(davinci_soc_info.intc_base,
> +					SZ_8K);
> +	}
>  	if (WARN_ON(!davinci_intc_base))
>  		return -EINVAL;
>  
> @@ -206,7 +218,15 @@ int __init __cp_intc_init(struct device_node *node)
>  	return 0;
>  }
>  
> +static struct of_device_id irq_match[] __initdata = {
> +	{ .compatible = "ti,cp-intc", .data = __cp_intc_init, },
> +	{ }
> +};
> +
>  void __init cp_intc_init(void)
>  {
> -	__cp_intc_init(NULL);
> +	if (!of_find_compatible_node(NULL, NULL, "ti,cp-intc"))
> +		__cp_intc_init(NULL, NULL);
> +	else
> +		of_irq_init(irq_match);

It turns out of_irq_init() does not exist on non-DT builds so this cause
build breakage when DT is not being used. Looking around, other
platforms are calling of_irq_init() in the generic DT board file and not
in the interrupt controller code. See arch/arm/mach-at91/board-dt.c or
arch/arm/mach-omap2/board-generic.c for examples. We need to adopt a
similar strategy for DaVinci.

To save time, I implemented these fixes and created a new patch which I
will send across shortly. Please have a look at that and let me know if
it works for you. I tested the patch on AM18x EVM.

Thanks,
Sekhar