From: jon-hunter@ti•com (Jon Hunter)
To: linux-arm-kernel@lists•infradead.org
Subject: [PATCH 4/4] OMAP: mtd: gpmc: add DT bindings for GPMC timings and NAND
Date: Wed, 24 Oct 2012 20:53:54 -0500 [thread overview]
Message-ID: <50889BB2.3090107@ti.com> (raw)
In-Reply-To: <1350935758-9215-5-git-send-email-zonque@gmail.com>
On 10/22/2012 02:55 PM, Daniel Mack wrote:
> This patch adds basic DT bindings for OMAP GPMC.
>
> The actual peripherals are instanciated from child nodes within the GPMC
> node, and the only type of device that is currently supported is NAND.
>
> Code was added to parse the generic GPMC timing parameters and some
> documentation with examples on how to use them.
>
> Successfully tested on an AM33xx board.
>
> Signed-off-by: Daniel Mack <zonque@gmail•com>
> ---
> Documentation/devicetree/bindings/bus/gpmc.txt | 59 +++++++++
> .../devicetree/bindings/mtd/gpmc-nand.txt | 65 ++++++++++
> arch/arm/mach-omap2/gpmc.c | 139 +++++++++++++++++++++
> 3 files changed, 263 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/bus/gpmc.txt
> create mode 100644 Documentation/devicetree/bindings/mtd/gpmc-nand.txt
>
> diff --git a/Documentation/devicetree/bindings/bus/gpmc.txt b/Documentation/devicetree/bindings/bus/gpmc.txt
> new file mode 100644
> index 0000000..ef1c6e1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/bus/gpmc.txt
> @@ -0,0 +1,59 @@
> +Device tree bindings for OMAP general purpose memory controllers (GPMC)
> +
> +The actual devices are instantiated from the child nodes of a GPMC node.
> +
> +Required properties:
> +
> + - compatible: Should be set to "ti,gpmc"
> +
> +Timing properties for child nodes. All are optional and default to 0.
> +
> + - gpmc,sync-clk: Minimum clock period for synchronous mode, in picoseconds
> +
> + Chip-select signal timings corresponding to GPMC_CS_CONFIG2:
> + - gpmc,cs-on: Assertion time
> + - gpmc,cs-rd-off: Read deassertion time
> + - gpmc,cs-wr-off: Write deassertion time
> +
> + ADV signal timings corresponding to GPMC_CONFIG3:
> + - gpmc,adv-on: Assertion time
> + - gpmc,adv-rd-off: Read deassertion time
> + - gpmc,adv-wr-off: Write deassertion time
> +
> + WE signals timings corresponding to GPMC_CONFIG4:
> + - gpmc,we-on: Assertion time
> + - gpmc,we-off: Deassertion time
> +
> + OE signals timings corresponding to GPMC_CONFIG4
> + - gpmc,oe-on: Assertion time
> + - gpmc,oe-off: Deassertion time
> +
> + Access time and cycle time timings corresponding to GPMC_CONFIG5
> + - gpmc,page-burst-access: Multiple access word delay
> + - gpmc,access: Start-cycle to first data valid delay
> + - gpmc,rd-cycle: Total read cycle time
> + - gpmc,wr-cycle: Total write cycle time
> +
> +The following are only on OMAP3430
> + - gpmc,wr-access
> + - gpmc,wr-data-mux-bus
> +
> +
> +Example for an AM33xx board:
> +
> + gpmc: gpmc at 50000000 {
> + compatible = "ti,gpmc";
> + ti,hwmods = "gpmc";
> + reg = <0x50000000 0x1000000>;
Nit-pick, that size is quite large for a register range. I recommend
looking at the HWMOD data file
(arch/arm/mach-omap2/omap_hwmod_33xx_data.c) and see how much space is
allocated for the registers (see structure am33xx_gpmc_addr_space).
Cheers
Jon
next prev parent reply other threads:[~2012-10-25 1:53 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-22 19:55 [PATCH 0/4] RFC: OMAP GPMC bindings Daniel Mack
2012-10-22 19:55 ` [PATCH 1/4] mtd: omap-nand: pass device_node in platform data Daniel Mack
2012-10-22 19:55 ` [PATCH 2/4] ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs Daniel Mack
2012-10-22 19:55 ` [PATCH 3/4] ARM: OMAP: gpmc: don't create devices from initcall on DT Daniel Mack
2012-10-22 19:55 ` [PATCH 4/4] OMAP: mtd: gpmc: add DT bindings for GPMC timings and NAND Daniel Mack
2012-10-24 23:27 ` Tony Lindgren
2012-10-24 23:31 ` Daniel Mack
2012-10-29 8:10 ` Afzal Mohammed
2012-10-29 11:15 ` Daniel Mack
2012-10-29 11:28 ` Afzal Mohammed
2012-10-29 12:32 ` Daniel Mack
2012-10-29 12:56 ` Afzal Mohammed
2012-10-25 1:28 ` Jon Hunter
2012-10-25 8:00 ` Daniel Mack
2012-10-25 13:16 ` Jon Hunter
2012-10-29 8:09 ` Afzal Mohammed
2012-10-25 1:53 ` Jon Hunter [this message]
2012-10-25 9:43 ` Daniel Mack
2012-10-25 13:22 ` Jon Hunter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=50889BB2.3090107@ti.com \
--to=jon-hunter@ti$(echo .)com \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox