Subject: [PATCH v2 3/3] usb: musb: omap: Add device tree support for omap musb glue

From: [email-masked] (Sergei Shtylyov)
Date: Tue, 08 Jan 2013 22:32:16 +0300

Hello.

On 09/11/2012 01:09 PM, Kishon Vijay Abraham I wrote:

> Added device tree support for omap musb driver and updated the
> Documentation with device tree binding information.

> Signed-off-by: Kishon Vijay Abraham I <[email-masked]>

   Belated comments to the patch which didn't pass my message size filter in
time. :-)

> diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
> index f4d9503..d96873b 100644
> --- a/drivers/usb/musb/omap2430.c
> +++ b/drivers/usb/musb/omap2430.c
[...]
> @@ -470,8 +471,11 @@ static u64 omap2430_dmamask = DMA_BIT_MASK(32);
>  static int __devinit omap2430_probe(struct platform_device *pdev)
>  {
>  	struct musb_hdrc_platform_data	*pdata = pdev->dev.platform_data;
> +	struct omap_musb_board_data	*data;
>  	struct platform_device		*musb;
>  	struct omap2430_glue		*glue;
> +	struct device_node		*np = pdev->dev.of_node;
> +	struct musb_hdrc_config		*config;
>  	struct resource			*res;
>  	int				ret = -ENOMEM;
>  
> @@ -501,6 +505,42 @@ static int __devinit omap2430_probe(struct platform_device *pdev)
>  	if (glue->control_otghs == NULL)
>  		dev_dbg(&pdev->dev, "Failed to obtain control memory\n");
>  
> +	if (np) {
> +		pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
> +		if (!pdata) {
> +			dev_err(&pdev->dev,
> +				"failed to allocate musb platfrom data\n");
> +			ret = -ENOMEM;

   'ret' is pre-initialized to -ENOMEM.

> +			goto err1;
> +		}
> +
> +		data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> +		if (!data) {
> +			dev_err(&pdev->dev,
> +					"failed to allocate musb board data\n");

   Overindented this line.

> +			ret = -ENOMEM;

   Same comment about already pre-initialized variable.

> +			goto err1;
> +		}
> +
> +		config = devm_kzalloc(&pdev->dev, sizeof(*config), GFP_KERNEL);
> +		if (!data) {

   You allocate 'config' but check 'data' again, so instead of exiting
gracefully we get an oops later on...

> +			dev_err(&pdev->dev,
> +				"failed to allocate musb hdrc config\n");

   No 'ret = -ENOMEM;' here -- kinda inconsistent. :-)

> +			goto err1;
> +		}
> +
> +		of_property_read_u32(np, "mode", (u32 *)&pdata->mode);
> +		of_property_read_u32(np, "interface_type",
> +						(u32 *)&data->interface_type);
> +		of_property_read_u32(np, "num_eps", (u32 *)&config->num_eps);
> +		of_property_read_u32(np, "ram_bits", (u32 *)&config->ram_bits);
> +		of_property_read_u32(np, "power", (u32 *)&pdata->power);
> +		config->multipoint = of_property_read_bool(np, "multipoint");
> +
> +		pdata->board_data	= data;
> +		pdata->config		= config;
> +	}
> +
>  	pdata->platform_ops		= &omap2430_ops;
>  
>  	platform_set_drvdata(pdev, glue);

   Don't worry now, I've just sent two patches to address these shortcomings.

WBR, Sergei