From: elen.song@atmel•com (elen.song)
To: linux-arm-kernel@lists•infradead.org
Subject: [PATCH V2 5/8] serial: at91: support run time switch transfer mode
Date: Thu, 18 Jul 2013 17:21:00 +0800 [thread overview]
Message-ID: <51E7B37C.5090105@atmel.com> (raw)
In-Reply-To: <20130718081520.GC16015@ns203013.ovh.net>
Hi JC:
On 7/18/2013 4:15 PM, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 10:43 Tue 16 Jul , Elen Song wrote:
>> We will switch to pio mode when request of dma or pdc fail.
>> But soon or later, when the request is success, the transfer mode can switch to them at
>> next open serial port action.
>> So in startup stage, we should get original transfer mode.
> You need to update the Documentation of the binding to said the driver support
> dmas bindings for the new IP
one question, it seems the document should write like:
use DMA:
usart0: serial at f001c000{
compatible = "atmel,at91sam9260-usart";
dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
<&dma0 2
(AT91_DMA_CFG_PER_ID(3)|AT91_DMA_CFG_FIFOCFG_ASAP)>;
dma-names = "tx","rx";
};
Should I replace macros with typical values?
Best regards
> and please use true/false for boolean
>
> and check the white space
>> Signed-off-by: Elen Song <elen.song@atmel•com>
>> ---
>> drivers/tty/serial/atmel_serial.c | 139 +++++++++++++++++++++----------------
>> 1 file changed, 80 insertions(+), 59 deletions(-)
>>
>> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
>> index 298b58c..ad787fd1 100644
>> --- a/drivers/tty/serial/atmel_serial.c
>> +++ b/drivers/tty/serial/atmel_serial.c
>> @@ -1371,6 +1371,80 @@ static void atmel_tasklet_func(unsigned long data)
>> spin_unlock(&port->lock);
>> }
>>
>> +static int atmel_init_property(struct atmel_uart_port *atmel_port,
>> + struct platform_device *pdev)
>> +{
>> + struct device_node *np = pdev->dev.of_node;
>> + struct atmel_uart_data *pdata = pdev->dev.platform_data;
>> +
>> + if (np) {
>> + /* DMA/PDC usage specification */
>> + if (of_get_property(np, "atmel,use-dma-rx", NULL)) {
>> + if (of_get_property(np, "dmas", NULL)) {
>> + atmel_port->use_dma_rx = 1;
>> + atmel_port->use_pdc_rx = 0;
>> + } else {
>> + atmel_port->use_dma_rx = 0;
>> + atmel_port->use_pdc_rx = 1;
>> + }
>> + } else {
>> + atmel_port->use_dma_rx = 0;
>> + atmel_port->use_pdc_rx = 0;
>> + }
>> +
>> + if (of_get_property(np, "atmel,use-dma-tx", NULL)) {
>> + if (of_get_property(np, "dmas", NULL)) {
>> + atmel_port->use_dma_tx = 1;
>> + atmel_port->use_pdc_tx = 0;
>> + } else {
>> + atmel_port->use_dma_tx = 0;
>> + atmel_port->use_pdc_tx = 1;
>> + }
>> + } else {
>> + atmel_port->use_dma_tx = 0;
>> + atmel_port->use_pdc_tx = 0;
>> + }
>> +
>> + } else {
>> + atmel_port->use_pdc_rx = pdata->use_dma_rx;
>> + atmel_port->use_pdc_tx = pdata->use_dma_tx;
>> + atmel_port->use_dma_rx = 0;
>> + atmel_port->use_dma_tx = 0;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void atmel_init_rs485(struct atmel_uart_port *atmel_port,
>> + struct platform_device *pdev)
>> +{
>> + struct device_node *np = pdev->dev.of_node;
>> + struct atmel_uart_data *pdata = pdev->dev.platform_data;
>> +
>> + if (np) {
>> + u32 rs485_delay[2];
>> + /* rs485 properties */
>> + if (of_property_read_u32_array(np, "rs485-rts-delay",
>> + rs485_delay, 2) == 0) {
>> + struct serial_rs485 *rs485conf = &atmel_port->rs485;
>> +
>> + rs485conf->delay_rts_before_send = rs485_delay[0];
>> + rs485conf->delay_rts_after_send = rs485_delay[1];
>> + rs485conf->flags = 0;
>> +
>> + if (of_get_property(np, "rs485-rx-during-tx", NULL))
>> + rs485conf->flags |= SER_RS485_RX_DURING_TX;
>> +
>> + if (of_get_property(np, "linux,rs485-enabled-at-boot-time",
>> + NULL))
>> + rs485conf->flags |= SER_RS485_ENABLED;
>> + }
>> + } else {
>> + atmel_port->rs485 = pdata->rs485;
>> + }
>> +
>> +}
>> +
>> static void atmel_set_ops(struct uart_port *port)
>> {
>> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>> @@ -1409,6 +1483,7 @@ static void atmel_set_ops(struct uart_port *port)
>> */
>> static int atmel_startup(struct uart_port *port)
>> {
>> + struct platform_device *pdev = to_platform_device(port->dev);
>> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>> struct tty_struct *tty = port->state->port.tty;
>> int retval;
>> @@ -1433,6 +1508,8 @@ static int atmel_startup(struct uart_port *port)
>> /*
>> * Initialize DMA (if necessary)
>> */
>> + atmel_init_property(atmel_port, pdev);
>> +
>> if (atmel_port->prepare_rx) {
>> retval = atmel_port->prepare_rx(port);
>> if (retval < 0)
>> @@ -1878,55 +1955,6 @@ static struct uart_ops atmel_pops = {
>> #endif
>> };
>>
>> -static void atmel_of_init_port(struct atmel_uart_port *atmel_port,
>> - struct device_node *np)
>> -{
>> - u32 rs485_delay[2];
>> -
>> - /* DMA/PDC usage specification */
>> - if (of_get_property(np, "atmel,use-dma-rx", NULL)) {
>> - if (of_get_property(np, "dmas", NULL)) {
>> - atmel_port->use_dma_rx = 1;
>> - atmel_port->use_pdc_rx = 0;
>> - } else {
>> - atmel_port->use_dma_rx = 0;
>> - atmel_port->use_pdc_rx = 1;
>> - }
>> - } else {
>> - atmel_port->use_dma_rx = 0;
>> - atmel_port->use_pdc_rx = 0;
>> - }
>> -
>> - if (of_get_property(np, "atmel,use-dma-tx", NULL)) {
>> - if (of_get_property(np, "dmas", NULL)) {
>> - atmel_port->use_dma_tx = 1;
>> - atmel_port->use_pdc_tx = 0;
>> - } else {
>> - atmel_port->use_dma_tx = 0;
>> - atmel_port->use_pdc_tx = 1;
>> - }
>> - } else {
>> - atmel_port->use_dma_tx = 0;
>> - atmel_port->use_pdc_tx = 0;
>> - }
>> -
>> - /* rs485 properties */
>> - if (of_property_read_u32_array(np, "rs485-rts-delay",
>> - rs485_delay, 2) == 0) {
>> - struct serial_rs485 *rs485conf = &atmel_port->rs485;
>> -
>> - rs485conf->delay_rts_before_send = rs485_delay[0];
>> - rs485conf->delay_rts_after_send = rs485_delay[1];
>> - rs485conf->flags = 0;
>> -
>> - if (of_get_property(np, "rs485-rx-during-tx", NULL))
>> - rs485conf->flags |= SER_RS485_RX_DURING_TX;
>> -
>> - if (of_get_property(np, "linux,rs485-enabled-at-boot-time", NULL))
>> - rs485conf->flags |= SER_RS485_ENABLED;
>> - }
>> -}
>> -
>> /*
>> * Configure the port from the platform device resource info.
>> */
>> @@ -1936,17 +1964,10 @@ static void atmel_init_port(struct atmel_uart_port *atmel_port,
>> struct uart_port *port = &atmel_port->uart;
>> struct atmel_uart_data *pdata = pdev->dev.platform_data;
>>
>> - if (pdev->dev.of_node) {
>> - atmel_of_init_port(atmel_port, pdev->dev.of_node);
>> - } else {
>> - atmel_port->use_pdc_rx = pdata->use_dma_rx;
>> - atmel_port->use_pdc_tx = pdata->use_dma_tx;
>> - atmel_port->use_dma_rx = 0;
>> - atmel_port->use_dma_tx = 0;
>> - atmel_port->rs485 = pdata->rs485;
>> - }
>> + if (!atmel_init_property(atmel_port, pdev))
>> + atmel_set_ops(port);
>>
>> - atmel_set_ops(port);
>> + atmel_init_rs485(atmel_port, pdev);
>>
>> port->iotype = UPIO_MEM;
>> port->flags = UPF_BOOT_AUTOCONF;
>> --
>> 1.7.9.5
>>
next prev parent reply other threads:[~2013-07-18 9:21 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-07-16 2:43 [PATCH V2 0/8] serial: at91: make usart and uart support dma transfer Elen Song
2013-07-16 2:43 ` [PATCH V2 1/8] serial: at91: correct definition from DMA to PDC Elen Song
2013-07-18 7:49 ` Jean-Christophe PLAGNIOL-VILLARD
2013-07-16 2:43 ` [PATCH V2 2/8] serial: at91: use function pointer to choose pdc or pio Elen Song
2013-07-16 2:43 ` [PATCH V3 3/8] serial: at91: add tx dma support Elen Song
2013-07-16 2:43 ` [PATCH V2 4/8] serial: at91: add rx " Elen Song
2013-07-16 2:43 ` [PATCH V2 5/8] serial: at91: support run time switch transfer mode Elen Song
2013-07-18 8:15 ` Jean-Christophe PLAGNIOL-VILLARD
2013-07-18 9:21 ` elen.song [this message]
2013-07-18 12:36 ` Nicolas Ferre
[not found] ` <51E7A756.6010004@atmel.com>
2013-07-18 10:45 ` Jean-Christophe PLAGNIOL-VILLARD
2013-07-16 2:43 ` [PATCH V2 6/8] serial: at91: make DBGU support dma and pdc transfers Elen Song
2013-07-18 8:18 ` Jean-Christophe PLAGNIOL-VILLARD
2013-07-16 2:43 ` [PATCH V2 7/8] serial: at91: distinguish usart and uart Elen Song
2013-07-16 2:43 ` [PATCH V2 8/8] serial: at91: modify UART to use software timer to trigger rx Elen Song
2013-07-18 7:48 ` [PATCH V2 0/8] serial: at91: make usart and uart support dma transfer Jean-Christophe PLAGNIOL-VILLARD
2013-07-18 8:19 ` Jean-Christophe PLAGNIOL-VILLARD
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=51E7B37C.5090105@atmel.com \
--to=elen.song@atmel$(echo .)com \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox