Subject: [PATCH] arm: dts: am33xx: Add mmc nodes for am33xx platform

From: [email-masked] (Joel Fernandes)
Date: Fri, 6 Sep 2013 13:21:46 -0500

Hi George,

On 09/06/2013 03:21 AM, George Cherian wrote:
> Add mmc nodes for am33xx platforms
> 
> Signed-off-by: George Cherian <[email-masked]>
> ---
> Verified after applying [1] and [2]
> [1] - [PATCH v4 0/6] dma: edma: Support scatter-lists of any length - https://lkml.org/lkml/2013/8/29/466
> [2] - [PATCH v2] ARM: dts: add AM33XX EDMA support - https://lkml.org/lkml/2013/8/26/57

Thanks for the verification.

But, this patch should not be applied on its own as it a part of a bigger patch
I had submitted earlier that includes DTS for other derivative boards and
bindings Documentation. [3] That's the one to be applied and should be applied
only after the above patches are merged. I will resubmit this later again once
pending EDMA changes are merged. Thanks.

[3] https://lkml.org/lkml/2013/6/25/781

Regards,

-Joel
>  arch/arm/boot/dts/am33xx.dtsi | 35 +++++++++++++++++++++++++++++++++++
>  1 file changed, 35 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
> index b0badff..1df512d 100644
> --- a/arch/arm/boot/dts/am33xx.dtsi
> +++ b/arch/arm/boot/dts/am33xx.dtsi
> @@ -236,6 +236,41 @@
>  			status = "disabled";
>  		};
>  
> +		mmc1: mmc at 48061000 {
> +			compatible = "ti,omap4-hsmmc";
> +			reg = <0x48060000 0x1000>;
> +			interrupts = <64>;
> +			ti,hwmods = "mmc1";
> +			ti,dual-volt;
> +			ti,needs-special-reset;
> +			ti,needs-special-hs-handling;
> +			dmas = <&edma 24
> +				&edma 25>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		mmc2: mmc at 481d8000 {
> +			compatible = "ti,omap4-hsmmc";
> +			reg = <0x481d8000 0x1000>;
> +			interrupts = <28>;
> +			ti,hwmods = "mmc2";
> +			ti,needs-special-reset;
> +			dmas = <&edma 2
> +				&edma 3>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		mmc3: mmc at 47810000 {
> +			compatible = "ti,omap4-hsmmc";
> +			reg = <0x47810000 0x1000>;
> +			interrupts = <29>;
> +			ti,hwmods = "mmc3";
> +			ti,needs-special-reset;
> +			status = "disabled";
> +		};
> +
>  		wdt2: wdt at 44e35000 {
>  			compatible = "ti,omap3-wdt";
>  			ti,hwmods = "wd_timer2";
>