Subject: [PATCH v4 05/17] arch_timer: Move to generic sched_clock framework

From: [email-masked] (Stephen Boyd)
Date: Mon, 14 Oct 2013 11:55:43 -0700

On 10/14/13 11:44, Kevin Hilman wrote:
> Stephen Boyd <[email-masked]> writes:
>
>> Register with the generic sched_clock framework now that it
>> supports 64 bits. This fixes two problems with the current
>> sched_clock support for machines using the architected timers.
>> First off, we don't subtract the start value from subsequent
>> sched_clock calls so we can potentially start off with
>> sched_clock returning gigantic numbers. Second, there is no
>> support for suspend/resume handling so problems such as discussed
>> in 6a4dae5 (ARM: 7565/1: sched: stop sched_clock() during
>> suspend, 2012-10-23) can happen without this patch. Finally, it
>> allows us to move the sched_clock setup into drivers clocksource
>> out of the arch ports.
>>
>> Cc: Christopher Covington <[email-masked]>
>> Cc: Catalin Marinas <[email-masked]>
>> Signed-off-by: Stephen Boyd <[email-masked]>
> A boot failure on Exynos5/Arndale showed up in next-20131014[1], and a
> subsequent bisect has fingered this patch as the culprit.  
>
> I haven't had a chance to debug this any further, but wanted to share in
> case someone else can debug.  
>
> The console log is below, but don't think there is much useful there as
> it shows nothing after the 'Starting kernel ...' from u-boot.

debug_ll output would be nice. Anyway, that patch looks "weird". It is
definitely not what I sent out. Most notably, this hunk jumps out

@@ -471,6 +472,15 @@ static int __init arch_timer_register(void)
                goto out;
        }
 
+       clocksource_register_hz(&clocksource_counter, arch_timer_rate);
+       cyclecounter.mult = clocksource_counter.mult;
+       cyclecounter.shift = clocksource_counter.shift;
+       timecounter_init(&timecounter, &cyclecounter,
+                        arch_counter_get_cntvct());
+
+       /* 56 bits minimum, so we assume worst case rollover */
+       sched_clock_register(arch_timer_read_counter, 56, arch_timer_rate);
+
        if (arch_timer_use_virtual) {
                ppi = arch_timer_ppi[VIRT_PPI];
                err = request_percpu_irq(ppi, arch_timer_handler_virt,

Which is adding the clocksource_register_hz() and timecounter_init()
call twice. It should only be adding the sched_clock_register() call and
the sched_clock_register() call should be in arch_counter_register().
Can you try this patch?

----8<----

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 5d52789..865ecd8 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -420,6 +420,9 @@ static void __init arch_counter_register(unsigned type)
 	cyclecounter.mult = clocksource_counter.mult;
 	cyclecounter.shift = clocksource_counter.shift;
 	timecounter_init(&timecounter, &cyclecounter, start_count);
+
+	/* 56 bits minimum, so we assume worst case rollover */
+	sched_clock_register(arch_timer_read_counter, 56, arch_timer_rate);
 }
 
 static void arch_timer_stop(struct clock_event_device *clk)
@@ -472,15 +475,6 @@ static int __init arch_timer_register(void)
 		goto out;
 	}
 
-	clocksource_register_hz(&clocksource_counter, arch_timer_rate);
-	cyclecounter.mult = clocksource_counter.mult;
-	cyclecounter.shift = clocksource_counter.shift;
-	timecounter_init(&timecounter, &cyclecounter,
-			 arch_counter_get_cntvct());
-
-	/* 56 bits minimum, so we assume worst case rollover */
-	sched_clock_register(arch_timer_read_counter, 56, arch_timer_rate);
-
 	if (arch_timer_use_virtual) {
 		ppi = arch_timer_ppi[VIRT_PPI];
 		err = request_percpu_irq(ppi, arch_timer_handler_virt,

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation