Subject: [PATCH v4 1/5] ARM: dts: enable hdmi for exynos5250 based snow board

From: [email-masked] (Tomasz Figa)
Date: Wed, 14 May 2014 21:41:11 +0200

Hi Rahul,

On 14.05.2014 04:45, Rahul Sharma wrote:
> From: Rahul Sharma <[email-masked]>
> 
> Enable support for HDMI for exynos5250 based Snow board.
> 
> Signed-off-by: Rahul Sharma <[email-masked]>
> ---
>  arch/arm/boot/dts/exynos5250-cros-common.dtsi |    6 +++++-
>  arch/arm/boot/dts/exynos5250-pinctrl.dtsi     |    7 +++++++
>  arch/arm/boot/dts/exynos5250-snow.dts         |    7 +++++++
>  3 files changed, 19 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/exynos5250-cros-common.dtsi b/arch/arm/boot/dts/exynos5250-cros-common.dtsi
> index 2c1560d..89ac90f 100644
> --- a/arch/arm/boot/dts/exynos5250-cros-common.dtsi
> +++ b/arch/arm/boot/dts/exynos5250-cros-common.dtsi
> @@ -240,7 +240,7 @@
>  		samsung,i2c-sda-delay = <100>;
>  		samsung,i2c-max-bus-freq = <378000>;
>  
> -		hdmiphy at 38 {
> +		hdmiphy: hdmiphy at 38 {
>  			compatible = "samsung,exynos4212-hdmiphy";
>  			reg = <0x38>;
>  		};
> @@ -304,6 +304,10 @@
>  
>  	hdmi {
>  		hpd-gpio = <&gpx3 7 0>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&hdmi_hpd_irq>;
> +		phy = <&hdmiphy>;
> +		ddc = <&i2c_2>;
>  	};
>  
>  	gpio-keys {
> diff --git a/arch/arm/boot/dts/exynos5250-pinctrl.dtsi b/arch/arm/boot/dts/exynos5250-pinctrl.dtsi
> index 9a49e68..da3ae66 100644
> --- a/arch/arm/boot/dts/exynos5250-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/exynos5250-pinctrl.dtsi
> @@ -560,6 +560,13 @@
>  			samsung,pin-pud = <0>;
>  			samsung,pin-drv = <0>;
>  		};
> +
> +		hdmi_hpd_irq: hdmi-hpd-irq {
> +			samsung,pins = "gpx3-7";
> +			samsung,pin-function = <0>;
> +			samsung,pin-pud = <1>;
> +			samsung,pin-drv = <0>;
> +		};

Based on the fact that this is just being configured as input, I don't
think this is a generic special function, but rather a board-specific
GPIO, which should be defined in dts of respective board.

>  	};
>  
>  	pinctrl at 13400000 {
> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
> index 1ce1088..696850a 100644
> --- a/arch/arm/boot/dts/exynos5250-snow.dts
> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
> @@ -206,4 +206,11 @@
>  			clock-frequency = <24000000>;
>  		};
>  	};
> +
> +	hdmi {
> +		hdmi-en-supply = <&tps65090_fet7>;
> +		vdd-supply = <&ldo8_reg>;
> +		vdd_osc-supply = <&ldo10_reg>;
> +		vdd_pll-supply = <&ldo8_reg>;

Hmm, those regulators don't seem to be listed in
Documentation/devicetree/bindings/video/exynos_hdmi.txt, at least in
today's linux-next. The driver seems to use them, though.

This isn't a problem with this patch, but if you're working on this,
could you also fix the documentation in separate patch?

Best regards,
Tomasz