Subject: [PATCH 09/11] brcmfmac: Fix OOB interrupt not working for BCM43362

From: [email-masked] (Hans de Goede)
Date: Tue, 27 May 2014 23:28:57 +0200

Hi,

On 05/27/2014 07:03 PM, Arend van Spriel wrote:
> On 05/26/14 09:48, Hans de Goede wrote:
>> It has taken me a long long time to get the OOB interrupt working on the
>> AP6210 sdio wifi/bt module found on various Allwinner A20 boards. In the
>> end I found these magic register pokes in the cubietruck kernel tree:
>> https://github.com/cubieboard2/linux-sunxi/commit/7f08ba395617d17e7a711507503d89a50406fe7a
>>
>> I'm not entirely sure if this specific to the AP6210 module, or if this
>> should be done for all BCM43362 sdio devices.
>
> Let keep it as this for now. I added some remarks below.
>
> Regards,
> Arend
>
>> Signed-off-by: Hans de Goede<[email-masked]>
>> ---
>>   drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 18 ++++++++++++++++++
>>   1 file changed, 18 insertions(+)
>>
>> diff --git a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
>> index 0fc707c..2369a0f 100644
>> --- a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
>> +++ b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
>> @@ -39,7 +39,9 @@
>>   #include<brcm_hw_ids.h>
>>   #include<brcmu_utils.h>
>>   #include<brcmu_wifi.h>
>> +#include<chipcommon.h>
>>   #include<soc.h>
>> +#include "chip.h"
>>   #include "dhd_bus.h"
>>   #include "dhd_dbg.h"
>>   #include "sdio_host.h"
>> @@ -119,6 +121,7 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev)
>>   {
>>       int ret = 0;
>>       u8 data;
>> +    u32 addr, gpiocontrol;
>>       unsigned long flags;
>>
>>       if ((sdiodev->pdata)&&  (sdiodev->pdata->oob_irq_supported)) {
>> @@ -148,6 +151,21 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev)
>>
>>           sdio_claim_host(sdiodev->func[1]);
>>
>> +        if (sdiodev->bus_if->chip == BCM43362_CHIP_ID) {
> +            /* assign GPIO to SDIO core */
>> +            addr = CORE_CC_REG(SI_ENUM_BASE, gpiocontrol);
>> +            gpiocontrol = brcmf_sdiod_regrl(sdiodev, addr,&ret);
>> +            gpiocontrol |= 0x2;
>> +            brcmf_sdiod_regwl(sdiodev, addr, gpiocontrol,&ret);
>> +
>> +            /* SPROM_ADDR_HIGH ? perhaps the defines name is off */
>
> These names are all off. These should be:
> SBSDIO_SPROM_ADDR_HIGH = SBSDIO_GPIO_SELECT
> SBSDIO_CHIP_CTRL_DATA = SBSDIO_GPIO_OUT
> SBSDIO_CHIP_CTRL_EN = SBSDIO_GPIO_EN

Ok, so I guess I should do a pre-patch adding defines for these, should
these replace the existing defines for these addresses in:
drivers/net/wireless/brcm80211/brcmfmac/sdio_host.h

Or should the pre-patch add defines with the new names and keep the old
ones ?

Regards,

Hans