Subject: [PATCH v2] ARM: shmobile: r8a7790: link PCI USB devices to USB PHY

From: [email-masked] (Sergei Shtylyov)
Date: Thu, 29 May 2014 01:51:11 +0400

Hello.

On 05/27/2014 04:41 AM, Magnus Damm wrote:

>>>> Describe the PCI USB devices that are behind the PCI bridges, adding
>>>> necessary
>>>> links to the USB PHY device.

>>>> Based on the original work by Ben Dooks <[email-masked]>.

>>>> Signed-off-by: Sergei Shtylyov <[email-masked]>

>>>> ---
>>>> This patch is against 'renesas-devel-v3.15-rc7-20140526' tag of Simon
>>>> Horman's
>>>> 'renesas.git' repo plus R8A7790/Lager PCI and USB PHY support patches
>>>> posted
>>>> before. The patch requires the internal PCI DT support, USB PHY driver,
>>>> and
>>>> USB HCD generic PHY support (also already posted) in order to work.

>>>> Changes in version 2:
>>>> - renamed the PCI OHCI/EHCI device nodes to comply with the PCI binding;
>>>> - changed the PHY specifier in the PCI#2 node to reflect that channel #1
>>>> support
>>>>     was dropped;
>>>> - resolved rejects, refreshed the patch.

>>>>    arch/arm/boot/dts/r8a7790.dtsi |   28 ++++++++++++++++++++++++++++
>>>>    1 file changed, 28 insertions(+)

>>>> Index: renesas/arch/arm/boot/dts/r8a7790.dtsi
>>>> ===================================================================
>>>> --- renesas.orig/arch/arm/boot/dts/r8a7790.dtsi
>>>> +++ renesas/arch/arm/boot/dts/r8a7790.dtsi
>>>> @@ -919,6 +919,20 @@
>>>>                   interrupt-map = <0x0000 0 0 1 &gic 0 108
>>>> IRQ_TYPE_LEVEL_HIGH
>>>>                                    0x0800 0 0 1 &gic 0 108
>>>> IRQ_TYPE_LEVEL_HIGH
>>>>                                    0x1000 0 0 2 &gic 0 108
>>>> IRQ_TYPE_LEVEL_HIGH>;
>>>> +
>>>> +               usb at 0,1 {
>>>> +                       reg = <0x800 0 0 0 0>;
>>>> +                       device_type = "pci";
>>>> +                       phys = <&usbphy 0 0>;
>>>> +                       phy-names = "usb";
>>>> +               };
>>>> +
>>>> +               usb at 0,2 {
>>>> +                       reg = <0x1000 0 0 0 0>;
>>>> +                       device_type = "pci";
>>>> +                       phys = <&usbphy 0 0>;
>>>> +                       phy-names = "usb";
>>>> +               };
>>>>           };
>>>>
>>>>           pci1: pci at ee0b0000 {
>>>> @@ -955,5 +969,19 @@
>>>>                   interrupt-map = <0x0000 0 0 1 &gic 0 113
>>>> IRQ_TYPE_LEVEL_HIGH
>>>>                                    0x0800 0 0 1 &gic 0 113
>>>> IRQ_TYPE_LEVEL_HIGH
>>>>                                    0x1000 0 0 2 &gic 0 113
>>>> IRQ_TYPE_LEVEL_HIGH>;
>>>> +
>>>> +               usb at 0,1 {
>>>> +                       reg = <0x800 0 0 0 0>;
>>>> +                       device_type = "pci";
>>>> +                       phys = <&usbphy 1 0>;
>>>> +                       phy-names = "usb";
>>>> +               };
>>>> +
>>>> +               usb at 0,2 {
>>>> +                       reg = <0x1000 0 0 0 0>;
>>>> +                       device_type = "pci";
>>>> +                       phys = <&usbphy 1 0>;
>>>> +                       phy-names = "usb";
>>>> +               };
>>>>           };
>>>>    };

>>> Hi Sergei,

>>> Above I see two hunks of DTS code but my r8a7790 data sheet contains
>>> three USB PCI devices. Perhaps my understanding is wrong, or may there

>>     You probably wanted to say 6 (OHCI and EHCI are 2 different PCI devices).

> Sure. I guess it depends on if you count PCI host controllers or USB
> host controllers..

    You said "USB PCI devices", so I thought you meant the latter.

>>> is some other patch available to enable all USB PCI devices included
>>> in the SoC?

>>     This patch doesn't enable USB devices, it just links them to the PHY
>> where it makes sense (for USB channel #1 it doesn't).

> I know we've discussed this before, and for USB channel #1 you tend to
> say that the PHY is not necessary for operation. From my side I am not
> so sure. Over the months I seen several shortcuts and missing pieces
> so for now just assume this is another rushed attempt. As usual I
> would like to make sure the dependencies are correctly described in DT
> before merging anything.

> Like I mentioned earlier there are shared bits in UGCTRL register in

    Did you mean UGCTRL or UGCTRL2 register? My testing didn't prove that the 
UGCTRL bits (CONNECT and PLLRESET) affect anything but the USBHS controller -- 
my PHY driver only touches these bits if the PHY selected corresponds to the 
USBHS itself (which is not supported by DT yet)...

> the PHY. Those may or may not affect USB channel #1. Furthermore, on
> top of this we have the MSTP bit for the PHY that may or may not be
> related to USB channel #1.

    There is no MSTP bit for the PHY, there's MSTP bit for USBHS controller of 
which this PHY is a part.

> My opinion is that if the USB PHY requires the MSTP clock to be
> enabled when using USB channel #1 _or_ the UGCTRL bits affect the USB
> Channel #1 then DT needs to point out the relationship between the PHY
> and the USB Host

    I agree and I can conduct some additional tests only linking the USB 
channel #1 to the PHY driver, and hence enabling the USBHS clock only for it...

> so Runtime PM can be used in the PHY driver to
> dynamically manage the clock.

    Er, do you insist on using the runtime PM vs clock API? I'm not yet sure 
it'll work with a named clock...

> Thanks,
> / magnus

WBR, Sergei