Subject: [PATCH v5 08/14] mfd: max77802: Add DT binding documentation

From: [email-masked] (Andreas Färber)
Date: Fri, 27 Jun 2014 10:06:14 +0200

Am 26.06.2014 20:15, schrieb Javier Martinez Canillas:
> Add Device Tree binding documentation for Maxim 77802 PMIC.
> 
> Signed-off-by: Javier Martinez Canillas <[email-masked]>
> ---
> 
> Changes since v4: None
> 
> Changes since v3: None
> 
> Changes since v2:
>  - Explain better the Dynamic Voltage Scaling (DVS) support in some Buck
>    regulators and the max77802,pmic-buck-{dvs,selb}-gpios properties.
>    Suggested by Mark Brown.
> 
>  Documentation/devicetree/bindings/mfd/max77802.txt | 97 ++++++++++++++++++++++
>  1 file changed, 97 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/max77802.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/max77802.txt b/Documentation/devicetree/bindings/mfd/max77802.txt
> new file mode 100644
> index 0000000..f3b67c5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/max77802.txt
> @@ -0,0 +1,97 @@
> +Maxim MAX77802 multi-function device
> +
> +MAX77802 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is

"Multifunction"?

> +interfaced to host controller using i2c interface. PMIC, Charger and RTC
> +submodules are addressed using same i2c slave address.
> +
> +Buck regulators 1, 2, 3, 4 and 6 include Dynamic Voltage Scaling (DVS) that
> +allows each output voltage to change dynamically. Each Buck output voltage
> +is selected using a set of external inputs: DVS1-3 and SELB1, 2, 3 and 6.
> +
> +There are 8 DVS registers that can be used to configure the output voltage
> +for each Buck regulator and which one is active is controled by DVSx lines.
> +
> +SELBx lines are used to control if individual Buck lines are ON or OFF.
> +
> +This document describes the binding for mfd device and PMIC submodule.
> +
> +Binding for the built-in 32k clock generator block is defined separately
> +in bindings/clk/maxim,max77802.txt file.
> +
> +Required properties:
> +- compatible : Must be "maxim,max77802";
> +- reg : Specifies the i2c slave address of PMIC block.
> +- interrupts : This i2c device has an IRQ line connected to the main SoC.
> +- interrupt-parent : The parent interrupt controller.
> +
> +Optional properties:
> +- max77802,pmic-buck-default-dvs-idx: We'll always write this DVS index in the
> +  PMIC for Bucks with DVS.
> +  NOTE: at the moment these bindings don't include enough details for actual
> +  GPIO-DVS--this just lets you choose which single slot to use.
> +
> +- max77802,pmic-buck-dvs-gpios: A GPIO array where each GPIO is connected to a
> +  DVS line. We'll try to set these GPIOs to match pmic-buck-default-dvs-idx at
> +  probe time if they are defined. If some or all of these GPIOs are not defined
> +  it's assumed that the board has any missing GPIOs hardwired to match
> +  pmic-buck-default-dvs-idx.
> +
> +- max77802,pmic-buck-selb-gpios: A GPIO array where each GPIO is connected to a
> +  SELBx line. Should be five values: 1, 2, 3, 4, 6. It is strongly suggested to
> +  include these GPIOs if there's any chance that changing DVS GPIOs one line at
> +  a time might glitch your DVS values.
> +
> +Optional node:
> +- regulators : The regulators of max77802 have to be instantiated
> +  under subnode named "regulators" using the following format.
> +
> +	regulator_name {

The convention, I was told, would be regulator-name as node name.

> +		standard regulator constraints....
> +	};
> +	refer Documentation/devicetree/bindings/regulator/regulator.txt
> +
> +  The regulator node name should be initialized with a string
> +to get matched with their hardware counterparts as follow:
> +
> +	-LDOn 	:	for LDOs, where n can lie in range 1 to 35.
> +			example: LDO1, LDO2, LDO35.
> +	-BUCKn 	:	for BUCKs, where n can lie in range 1 to 10.
> +			example: BUCK1, BUCK5, BUCK10.
> +Example:
> +
> +	max77802 at 09 {
> +		compatible = "maxim,max77802";
> +		interrupt-parent = <&wakeup_eint>;
> +		interrupts = <26 0>;
> +		reg = <0x09>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		max77802,pmic-buck-default-dvs-idx = <1>;
> +		max77802,pmic-buck-dvs-gpios = <&gpy7 6 0>,
> +					       <&gpj4 2 0>,
> +					       <&gpj4 3 0>;
> +		max77802,pmic-buck-selb-gpios = <&gph0 2 0>,
> +						<&gph0 3 0>,
> +						<&gph0 4 0>,
> +						<&gph0 5 0>,
> +						<&gph0 6 0>;
> +
> +		regulators {
> +			ldo11_reg: LDO11 {
> +				regulator-compatible = "LDO11";
> +				regulator-name = "vdd_ldo11";
> +				regulator-min-microvolt = <1900000>;
> +				regulator-max-microvolt = <1900000>;
> +				regulator-always-on;
> +			};
> +
> +			buck1_reg {

Missing ": BUCK1"

> +				regulator-compatible = "BUCK1";
> +				regulator-name = "vdd_mif";
> +				regulator-min-microvolt = <950000>;
> +				regulator-max-microvolt = <1300000>;
> +				regulator-always-on;
> +				regulator-boot-on;
> +			};
> +	};

Regards,
Andreas

-- 
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imend?rffer; HRB 16746 AG N?rnberg