Subject: [PATCH v2] ARM: apq8064: Add pinmux and i2c pinctrl nodes

From: [email-masked] (Andreas Färber)
Date: Wed, 20 Aug 2014 17:36:37 +0200

Hi,

Am 20.08.2014 14:02, schrieb Kiran Padwal:
> This patch adds pinmux and i2c pinctrl DT node for IFC6410 board.
> It also adds necessary DT support for i2c eeprom which is present on
> IFC6410.
> 
> Tested on IFC6410 board.
> 
> Signed-off-by: Kiran Padwal <[email-masked]>
> ---
> Chages since v1:
> 	- Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux".
> 	- Updated pinmux interrupt.
> 
>  arch/arm/boot/dts/qcom-apq8064-ifc6410.dts |   29 ++++++++++++++
>  arch/arm/boot/dts/qcom-apq8064.dtsi        |   59 ++++++++++++++++++++++++++++
>  2 files changed, 88 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
> index 7c2441d..d52ac3c 100644
> --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
> +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
> @@ -5,6 +5,15 @@
>  	compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
>  
>  	soc {
> +		pinmux at 800000 {
> +			i2c1_pins: i2c1_pinmux {

Is there a requirement to have "_pinmux" in the subnode of the "pinmux"
node? Otherwise use just "i2c1"? I notice because the general convention
seems to be dashes rather than underscores for node names.

> +				mux {
> +					pins = "gpio20", "gpio21";
> +					function = "gsbi1";
> +				};
> +			};
> +		};
> +
>  		gsbi at 16600000 {
>  			status = "ok";
>  			qcom,mode = <GSBI_PROT_I2C_UART>;
> @@ -12,5 +21,25 @@
>  				status = "ok";
>  			};
>  		};
> +
> +		gsbi1: gsbi at 12440000 {
> +			qcom,mode = <GSBI_PROT_I2C>;
> +			status = "ok";

Usually the overridden status property goes first, as seen on the
previous gsbi node.

Further, its canonical value is "okay" (although in practice anything
other than "disabled" should work), so suggest you adopt it for your new
nodes.

Also, you already provide a label "gsbi1" to this node in the .dtsi
below, so you don't need to do it here again.
Some architectures prefer in such a case that in the .dts the node is
referenced as &gsbi1 {...}; below the root node in alphabetical order
rather than duplicating the full /soc/foo at bar hierarchy.

> +
> +			i2c1: i2c at 12460000 {

Suggest to move the i2c1 label to the .dtsi. Then optionally same could
be done here as outlined for gsbi1.

> +				status = "ok";

"okay".

> +
> +				clock-frequency = <200000>;
> +
> +				pinctrl-0 = <&i2c1_pins>;
> +				pinctrl-names = "default";
> +
> +				eeprom: eeprom at 52 {
> +					compatible = "atmel,24c128";
> +					reg = <0x52>;
> +					pagesize = <32>;
> +				};
> +			};
> +		};
>  	};
>  };
> diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
> index 92bf793..bb2ccde 100644
> --- a/arch/arm/boot/dts/qcom-apq8064.dtsi
> +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
> @@ -70,6 +70,17 @@
>  		ranges;
>  		compatible = "simple-bus";
>  
> +		tlmm_pinmux: pinmux at 800000 {
> +			compatible = "qcom,apq8064-pinctrl";
> +			reg = <0x800000 0x4000>;
> +
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			interrupts = <0 16 0x4>;

s/0x4/IRQ_TYPE_LEVEL_HIGH/?

> +		};
> +
>  		intc: interrupt-controller at 2000000 {
>  			compatible = "qcom,msm-qgic2";
>  			interrupt-controller;
> @@ -133,6 +144,54 @@
>  			regulator;
>  		};
>  
> +		gsbi1: gsbi at 12440000 {
> +			compatible = "qcom,gsbi-v1.0.0";
> +			reg = <0x12440000 0x100>;
> +			clocks = <&gcc GSBI1_H_CLK>;
> +			clock-names = "iface";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +			status = "disabled";
> +
> +			i2c at 12460000 {
> +				compatible = "qcom,i2c-qup-v1.1.1";
> +				reg = <0x12460000 0x1000>;
> +				interrupts = <0 194 0>;

The trailing 0 might be IRQ_TYPE_NONE?

> +
> +				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
> +				clock-names = "core", "iface";
> +				status = "disabled";

I'd guess this is redundant since the parent is already disabled?

> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +		};
> +
> +		gsbi2: gsbi at 12480000 {
> +			compatible = "qcom,gsbi-v1.0.0";
> +			reg = <0x12480000 0x100>;
> +			clocks = <&gcc GSBI2_H_CLK>;
> +			clock-names = "iface";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +			status = "disabled";
> +
> +			i2c at 124a0000 {
> +				compatible = "qcom,i2c-qup-v1.1.1";
> +				reg = <0x124a0000 0x1000>;
> +				interrupts = <0 196 0>;

Again, IRQ_TYPE_NONE possibly?

Cheers,
Andreas

> +
> +				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
> +				clock-names = "core", "iface";
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +		};
> +
>  		gsbi7: gsbi at 16600000 {
>  			status = "disabled";
>  			compatible = "qcom,gsbi-v1.0.0";

-- 
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imend?rffer; HRB 16746 AG N?rnberg