Subject: [RFC PATCH for AMD Seattle 0/4] Drivers for AMD-Seatlle to boot from ACPI

From: [email-masked] (Suravee Suthikulpanit)
Date: Mon, 15 Sep 2014 23:28:07 -0500

Note: Correcting the typo for linux-acpi mailing list in this reply.

Also, I would like to add the link to the "AMD Opteron? A1100 Series 
Processor ACPI Porting Guide", which describes the current ACPI table 
for AMD Seattle platform here:

http://amd-dev.wpengine.netdna-cdn.com/wordpress/media/2012/10/Seattle_ACPI_Guide.pdf

Suravee

On 09/15/2014 07:47 PM, suravee.suthikulpanit at amd.com wrote:
> From: Suravee Suthikulpanit <[email-masked]>
>
> As a follow up of the email thread:
>
>      [PATCH v3 00/17] Introduce ACPI for ARM64 based on ACPI 5.1
>      https://lkml.org/lkml/2014/9/1/446
>
> Besides Hanjun Guo's patches above, these are the additional patches required
> to boot AMD Seattle platform with full ACPI support:
>
>      [PATCH] efi/arm64: efistub: don't abort if base of DRAM is occupied
>      http://lists.infradead.org/pipermail/linux-arm-kernel/2014-July/272274.html
>
>      [PATCH v2] efi/arm64: fix fdt-related memory reservation
>      https://lkml.org/lkml/2014/9/8/483
>
>      [PATCH] ata: ahci_platform: Add ACPI support for AMD Seattle SATA controller
>      https://lkml.org/lkml/2014/9/9/834
>
>      [RFC PATCH for Juno 2/2] tty: SBSA compatible UART
>      https://lkml.org/lkml/2014/9/1/448
>      (NOTE: This is not meant to be submitted upstream, but required to enable
>       ACPI support for UART SBSA driver.)
>
> These patches are rebased from the linux-3.17-rc4 upstream kernel, and
> compatible with the AMD Seattle Firmware version ROD0070C.
> The full kernel boot log can be found here:
>
>      http://people.linaro.org/~al.stone/seattle-boot-acpi-dmesg.txt
>
> Suravee / Al
>
> Ard Biesheuvel (1):
>    arm64/efi: efistub: don't abort if base of DRAM is occupied
>
> Grame Gregory (1):
>    [RFC PATCH for Juno 2/2] tty: SBSA compatible UART
>
> Mark Salter (1):
>    efi/arm64: fix fdt-related memory reservation
>
> Suravee Suthikulpanit (1):
>    ata: ahci_platform: Add ACPI support for AMD Seattle SATA controller
>
>   arch/arm64/kernel/efi-stub.c       |  16 +-
>   arch/arm64/mm/init.c               |   3 +-
>   drivers/ata/Kconfig                |   2 +-
>   drivers/ata/ahci_platform.c        |  13 ++
>   drivers/firmware/efi/libstub/fdt.c |  10 +-
>   drivers/tty/Kconfig                |   6 +
>   drivers/tty/Makefile               |   1 +
>   drivers/tty/sbsauart.c             | 328 +++++++++++++++++++++++++++++++++++++
>   8 files changed, 365 insertions(+), 14 deletions(-)
>   create mode 100644 drivers/tty/sbsauart.c
>