Subject: [PATCH 4/7] pinctrl: zynq: Document DT binding

From: [email-masked] (Andreas Färber)
Date: Wed, 05 Nov 2014 04:35:18 +0100

Am 03.11.2014 um 20:05 schrieb Soren Brinkmann:
> Add documentation for the devicetree binding for the Zynq pincontroller.
> 
> Signed-off-by: Soren Brinkmann <[email-masked]>
> ---
>  .../bindings/pinctrl/xlnx,zynq-pinctrl.txt         | 90 ++++++++++++++++++++++
>  1 file changed, 90 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt
> new file mode 100644
> index 000000000000..86a86b644e6c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt
> @@ -0,0 +1,90 @@
> +	Binding for Xilinx Zynq Pinctrl
> +
> +Required properties:
> +- compatible: "xlnx,zynq-pinctrl"
> +- syscon: phandle to SLCR
> +- reg: Offset and length of pinctrl space in SLCR
> +
> +Please refer to pinctrl-bindings.txt in this directory for details of the
> +common pinctrl bindings used by client devices, including the meaning of the
> +phrase "pin configuration node".
> +
> +Zynq's pin configuration nodes act as a container for an abitrary number of

"arbitrary"

> +subnodes. Each of these subnodes represents some desired configuration for a
> +pin, a group, or a list of pins or groups. This configuration can include the
> +mux function to select on those pin(s)/group(s), and various pin configuration
> +parameters, such as pull-up, slew rate, etc.
> +
> +The name of each subnode is not important; all subnodes should be enumerated
> +and processed purely based on their content.
> +
> +Each subnode only affects those parameters that are explicitly listed. In
> +other words, a subnode that lists a mux function but no pin configuration
> +parameters implies no information about any pin configuration parameters.
> +Similarly, a pin subnode that describes a pullup parameter implies no
> +information about e.g. the mux function.
> +
> +
> +The following generic properties as defined in pinctrl-bindings.txt are valid
> +to specify in a pin configuration subnode:
> + groups, pins, function, bias-disable, bias-high-impedance, bias-pull-up,
> + slew-rate, low-power-disable, low-power-enable
> +
> + Valid arguments for 'slew-rate' are '0' and '1' to select between slow and fast
> + respectively.
> +
> + Valid values for groups are:
> +   ethernet0_0_grp, ethernet1_0_grp, mdio0_0_grp, mdio1_0_grp,
> +   qspi0_0_grp, qspi1_0_grp, qspi_fbclk, qspi_cs1_grp, spi0_0_grp,
> +   spi0_1_grp - spi0_2_grp, spi1_0_grp - spi1_3_grp, sdio0_0_grp - sdio0_2_grp,
> +   sdio1_0_grp - sdio1_3_grp, sdio0_emio_wp, sdio0_emio_cd, sdio1_emio_wp,
> +   sdio1_emio_cd, smc0_nor, smc0_nor_cs1_grp, smc0_nor_addr25_grp, smc0_nand,
> +   can0_0_grp - can0_10_grp, can1_0_grp - can1_11_grp, uart0_0_grp - uart0_10_grp,
> +   uart1_0_grp - uart1_11_grp, i2c0_0_grp - i2c0_10_grp, i2c1_0_grp - i2c1_10_grp,
> +   ttc0_0_grp - ttc0_2_grp, ttc1_0_grp - ttc1_2_grp, swdt0_0_grp - swdt0_4_grp,
> +   gpio0_0_grp - gpio0_53_grp
> +
> + Valid values for pins are:
> +   MIO0 - MIO53

What about the four EMIO_SD* pins?

> +
> + Valid values for function are:
> +   ethernet0, ethernet1, mdio0, mdio1, qspi0, qspi1, qspi_fbclk, qspi_cs1,
> +   spi0, spi1, sdio0, sdio0_pc, sdio0_cd, sdio0_wp,
> +   sdio1, sdio1_pc, sdio1_cd, sdio1_wp,
> +   smc0_nor, smc0_nor_cs1, smc0_nor_addr25, smc0_nand, can0, can1, uart0, uart1,
> +   i2c0, i2c1, ttc0, ttc1, swdt0, gpio0
> +
> +The following driver-specific properties as defined here are valid to specify in
> +a pin configuration subnode:
> + - io-standard: Configure the pin to use the selected IO standard according to
> +   this mapping:
> +    1: LVCMOS18
> +    2: LVCMOS25
> +    3: LVCMOS33
> +    4: HSTL
> +
> +Example:
> +	pinctrl0: pinctrl at 700 {
> +		compatible = "xlnx,pinctrl-zynq";
> +		reg = <0x700 0x200>;
> +		syscon = <&slcr>;
> +
> +		pinctrl_uart1_default: pinctrl-uart1-default {

Nit: Is it really necessary to prefix subnodes of "pinctrl at 700" with
"pinctrl-", here and in .dts?

> +			common {
> +				groups = "uart1_10_grp";
> +				function = "uart1";
> +				slew-rate = <0>;
> +				io-standard = <1>;
> +			};
> +
> +			rx {
> +				pins = "MIO49";
> +				bias-high-impedance;
> +			};
> +
> +			tx {
> +				pins = "MIO48";
> +				bias-disable;
> +			};
> +		};
> +	};

Otherwise looks good.

Cheers,
Andreas

-- 
SUSE LINUX GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imend?rffer; HRB 21284 AG N?rnberg