From: gregory.clement@free-electrons•com (Gregory CLEMENT)
To: linux-arm-kernel@lists•infradead.org
Subject: MUSB dual-role on AM335x behaving weirdly
Date: Tue, 04 Aug 2015 16:23:02 +0200 [thread overview]
Message-ID: <55C0CAC6.3020603@free-electrons.com> (raw)
In-Reply-To: <55C0B954.3020106@free-electrons.com>
Hi again,
On 04/08/2015 15:08, Gregory CLEMENT wrote:
> Hi Bin,
>
> On 02/07/2015 19:05, Bin Liu wrote:
>> Hi,
>>
>> On Thu, Jul 2, 2015 at 2:16 AM, Gregory CLEMENT
>> <gregory.clement@free-electrons•com> wrote:
>>> Hi Felipe,
>>>
>>> On 27/05/2015 11:42, Alexandre Belloni wrote:
>>>> Hi,
>>>>
>>>> On 26/05/2015 at 09:51:18 -0500, Felipe Balbi wrote :
>>>>> On Thu, May 14, 2015 at 04:36:33PM -0500, Bin Liu wrote:
>>>>>> Alexandre,
>>>>>>
>>>>>> On Thu, May 14, 2015 at 4:26 PM, Alexandre Belloni
>>>>>> <alexandre.belloni@free-electrons•com> wrote:
>>>>>>> On 14/05/2015 at 16:16:12 -0500, Bin Liu wrote :
>>>>>>>> I think I found the root cause of the problem: board design issue - I
>>>>>>>> bet the custom board has too much cap on VBUS line. It should be <
>>>>>>>> 10uF.
>>>>>>>>
>>>>>>>
>>>>>>> We have a custom board that exhibits the issue but it only has a 100nF
>>>>>>> cap on VBUS.
>>>>>>
>>>>>> Have you measured the VBUS discharging? Is there any way to share your
>>>>>> schematics?
>>>>>
>>>>> Alexandre, any further comments ?
>>>>>
>>>>
>>>> Yeah, I have just got more info.
>>>>
>>>> This is the relevant part of the schematic:
>>>> http://free-electrons.com/~alexandre/usb.png
>>>>
>>>> The total VBUS capacitance is 200nF and the USB0 pins are connected
>>>> directly to the AM3358 pins. U1 is actually not fitted.
>>>>
>>>> We didn't measure VBUS discharging but we observe the OTG pin sensing
>>>> stops when plugging an OTG cable without any device.
>>>
>>> Do you have any news about this topic?
>>>
>>>
>>> Is there something else that we can do to help solving this issue?
>>
>> In the case of CONFIG_USB_MUSB_DUAL_ROLE=y and dr_mode=otg, how is the
>> gadget driver configured? It has to be a module not built-in.
>
> Indeed when I configured CONFIG_USB_MUSB_HDRC=m and CONFIG_USB_MUSB_DSPS=m
> it worked seamless.
>
Actually it didn't worked. And now sometimes I even received continuously
the following message:
musb_bus_suspend 2484: trying to suspend as a_wait_vfall while active
Gregory
--
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
next prev parent reply other threads:[~2015-08-04 14:23 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-01-21 16:06 MUSB dual-role on AM335x behaving weirdly Maxime Ripard
2015-01-21 18:53 ` Bin Liu
2015-01-22 7:37 ` Yegor Yefremov
2015-01-22 10:43 ` Maxime Ripard
2015-01-22 11:01 ` Markus Pargmann
2015-01-22 14:00 ` Maxime Ripard
2015-01-22 14:52 ` Bin Liu
2015-02-05 13:21 ` Maxime Ripard
2015-02-24 10:39 ` Maxime Ripard
2015-02-24 14:54 ` Felipe Balbi
2015-02-24 16:50 ` Maxime Ripard
2015-02-24 17:33 ` Felipe Balbi
2015-02-25 11:11 ` Maxime Ripard
2015-02-25 12:11 ` Yegor Yefremov
2015-05-14 17:07 ` Felipe Balbi
2015-05-14 17:40 ` Felipe Balbi
2015-05-14 17:49 ` Felipe Balbi
2015-05-14 19:04 ` Felipe Balbi
2015-05-14 19:19 ` Bin Liu
2015-05-14 19:21 ` Felipe Balbi
2015-05-14 19:29 ` Bin Liu
2015-05-14 19:29 ` Felipe Balbi
2015-05-14 19:49 ` Felipe Balbi
2015-05-14 20:03 ` Bin Liu
2015-05-14 20:10 ` Felipe Balbi
2015-05-14 21:04 ` Bin Liu
2015-05-14 21:16 ` Bin Liu
2015-05-14 21:26 ` Alexandre Belloni
2015-05-14 21:36 ` Bin Liu
2015-05-26 14:51 ` Felipe Balbi
2015-05-27 9:42 ` Alexandre Belloni
2015-07-02 7:16 ` Gregory CLEMENT
2015-07-02 17:05 ` Bin Liu
2015-08-04 13:08 ` Gregory CLEMENT
2015-08-04 14:23 ` Gregory CLEMENT [this message]
2015-08-04 19:32 ` Felipe Balbi
2015-08-18 12:36 ` Gregory CLEMENT
2015-08-18 14:13 ` Felipe Balbi
2015-08-20 16:35 ` Gregory CLEMENT
2015-08-20 16:46 ` Felipe Balbi
2015-08-21 12:19 ` Gregory CLEMENT
2015-04-14 15:46 ` Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55C0CAC6.3020603@free-electrons.com \
--to=gregory.clement@free-electrons$(echo .)com \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox