From: petr.cvek@tul•cz (Petr Cvek)
To: linux-arm-kernel@lists•infradead.org
Subject: [PATCH v4 18/26] ARM: pxa: magician: Add support for ADS7846
Date: Mon, 28 Sep 2015 23:38:15 +0200 [thread overview]
Message-ID: <5609B347.80202@tul.cz> (raw)
In-Reply-To: <cover.1443472089.git.petr.cvek@tul.cz>
Add support for an ADS7846 touchscreen.
Signed-off-by: Petr Cvek <petr.cvek@tul•cz>
---
arch/arm/mach-pxa/magician.c | 86 ++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 86 insertions(+)
diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c
index af8133a..450f35f 100644
--- a/arch/arm/mach-pxa/magician.c
+++ b/arch/arm/mach-pxa/magician.c
@@ -28,6 +28,7 @@
#include <linux/pwm_backlight.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/gpio-regulator.h>
+#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/usb/gpio_vbus.h>
#include <linux/i2c/pxa-i2c.h>
@@ -44,6 +45,10 @@
#include <linux/platform_data/irda-pxaficp.h>
#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
+#include <linux/spi/ads7846.h>
+
#include "devices.h"
#include "generic.h"
@@ -748,6 +753,37 @@ static struct platform_device bq24022 = {
};
/*
+ * fixed regulator for ads7846
+ */
+
+static struct regulator_consumer_supply ads7846_supply =
+ REGULATOR_SUPPLY("vcc", "spi2.0");
+
+static struct regulator_init_data vads7846_regulator = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &ads7846_supply,
+};
+
+static struct fixed_voltage_config vads7846 = {
+ .supply_name = "vads7846",
+ .microvolts = 3300000, /* probably */
+ .gpio = -EINVAL,
+ .startup_delay = 0,
+ .init_data = &vads7846_regulator,
+};
+
+static struct platform_device vads7846_device = {
+ .name = "reg-fixed-voltage",
+ .id = 1,
+ .dev = {
+ .platform_data = &vads7846,
+ },
+};
+
+/*
* MMC/SD
*/
@@ -879,6 +915,51 @@ static struct i2c_pxa_platform_data magician_i2c_power_info = {
};
/*
+ * Touchscreen
+ */
+
+static struct ads7846_platform_data ads7846_pdata = {
+ .model = 7846,
+ .x_min = 0,
+ .y_min = 0,
+ .x_max = 4096,
+ .y_max = 4096,
+ .x_plate_ohms = 180, /* for pressure in 0-255 */
+ .y_plate_ohms = 180,
+ .pressure_max = 255, /* up to 12bit sampling */
+ .debounce_max = 10,
+ .debounce_tol = 3,
+ .debounce_rep = 1,
+ .gpio_pendown = GPIO115_MAGICIAN_nPEN_IRQ,
+ .keep_vref_on = 1, /* FIXME, external Vref? */
+ .vref_delay_usecs = 100,
+ /* .wait_for_sync, GPIO77_LCD_BIAS low noise measure, latency! */
+};
+
+struct pxa2xx_spi_chip tsc2046_chip_info = {
+ .tx_threshold = 1,
+ .rx_threshold = 2,
+ .timeout = 64,
+ .gpio_cs = -1,
+};
+
+static struct pxa2xx_spi_master magician_spi_info = {
+ .num_chipselect = 1,
+ .enable_dma = 1,
+};
+
+static struct spi_board_info ads7846_spi_board_info[] __initdata = {
+ {
+ .modalias = "ads7846",
+ .bus_num = 2,
+ .max_speed_hz = 1857143,
+ .platform_data = &ads7846_pdata,
+ .controller_data = &tsc2046_chip_info,
+ .irq = PXA_GPIO_TO_IRQ(GPIO115_MAGICIAN_nPEN_IRQ),
+ },
+};
+
+/*
* Platform devices
*/
@@ -887,6 +968,7 @@ static struct platform_device *devices[] __initdata = {
&egpio,
&backlight,
&pasic3,
+ &vads7846_device,
&bq24022,
&gpio_vbus,
&power_supply,
@@ -944,6 +1026,10 @@ static void __init magician_init(void)
lcd_select ? &samsung_info : &toppoly_info);
} else
pr_err("LCD detection: CPLD mapping failed\n");
+
+ pxa2xx_set_spi_info(2, &magician_spi_info);
+ spi_register_board_info(ARRAY_AND_SIZE(ads7846_spi_board_info));
+
}
MACHINE_START(MAGICIAN, "HTC Magician")
--
1.7.12.1
next prev parent reply other threads:[~2015-09-28 21:38 UTC|newest]
Thread overview: 59+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <cover.1443472089.git.petr.cvek@tul.cz>
2015-09-28 21:09 ` [PATCH v4 01/26] ARM: pxa: magician: Fix indentation in machine files Petr Cvek
2015-10-03 12:14 ` Philipp Zabel
2015-09-28 21:10 ` [PATCH v4 02/26] ARM: pxa: magician: Change comments to be more informative Petr Cvek
2015-10-03 12:19 ` Philipp Zabel
2015-10-13 20:08 ` Robert Jarzmik
2015-09-28 21:10 ` [PATCH v4 03/26] ARM: pxa: magician: Print more specific error message for global GPIOs Petr Cvek
2015-10-03 12:19 ` Philipp Zabel
2015-09-28 21:11 ` [PATCH v4 04/26] ARM: pxa: magician: Optimize debug messages for LCD power Petr Cvek
2015-10-03 12:20 ` Philipp Zabel
2015-09-28 21:11 ` [PATCH v4 05/26] ARM: pxa: magician: Change description of LCD power GPIO Petr Cvek
2015-10-03 12:21 ` Philipp Zabel
2015-09-28 21:15 ` [PATCH v4 06/26] ARM: pxa: magician: Add new discovered EGPIO pins Petr Cvek
2015-10-03 12:23 ` Philipp Zabel
2015-09-28 21:15 ` [PATCH v4 07/26] ARM: pxa: magician: Fix HTC Magician pin mux definitions Petr Cvek
2015-10-03 12:30 ` Philipp Zabel
2015-10-05 2:15 ` Petr Cvek
2015-10-13 20:09 ` Robert Jarzmik
2015-09-28 21:15 ` [PATCH v4 08/26] ARM: pxa: magician: Rename abstract LCD GPIOs Petr Cvek
2015-10-03 12:31 ` Philipp Zabel
2015-09-28 21:16 ` [PATCH v4 09/26] ARM: pxa: magician: Optimize powerup delays for Samsung LCD Petr Cvek
2015-10-03 12:32 ` Philipp Zabel
2015-09-28 21:32 ` [PATCH v4 10/26] ARM: pxa: magician: Optimize Samsung LCD refresh to 50Hz Petr Cvek
2015-10-03 12:33 ` Philipp Zabel
2015-09-28 21:32 ` [PATCH v4 11/26] ARM: pxa: magician: Optimize EGPIO initial values Petr Cvek
2015-10-03 12:35 ` Philipp Zabel
2015-10-07 19:45 ` Robert Jarzmik
2015-09-28 21:32 ` [PATCH v4 12/26] ARM: pxa: magician: Rename charger cable detection EGPIOs Petr Cvek
2015-10-03 12:38 ` Philipp Zabel
2015-10-09 2:33 ` Petr Cvek
2015-09-28 21:33 ` [PATCH v4 13/26] ARM: pxa: magician: Fix and add charging detection functions Petr Cvek
2015-09-28 21:33 ` [PATCH v4 14/26] ARM: pxa: magician: Fix platform data for both PXA27x I2C controllers Petr Cvek
2015-10-03 12:41 ` Philipp Zabel
2015-09-28 21:34 ` [PATCH v4 15/26] ARM: pxa: magician: Fix redundant GPIO request for pxaficp_ir Petr Cvek
2015-09-28 21:34 ` [PATCH v4 16/26] ARM: pxa: magician: Fix support for Intel Strata NOR Flash Petr Cvek
2015-09-28 21:38 ` [PATCH v4 17/26] ARM: pxa: magician: Fix wrongly enabled USB host ports Petr Cvek
2015-10-03 12:45 ` Philipp Zabel
2015-10-05 2:03 ` Petr Cvek
2015-09-28 21:38 ` Petr Cvek [this message]
2015-10-03 12:49 ` [PATCH v4 18/26] ARM: pxa: magician: Add support for ADS7846 Philipp Zabel
2015-10-12 4:39 ` Petr Cvek
2015-09-28 21:38 ` [PATCH v4 19/26] ARM: pxa: magician: Add support for Omnivision OV9640 camera Petr Cvek
2015-10-03 12:50 ` Philipp Zabel
2015-10-07 19:49 ` Robert Jarzmik
2015-10-08 6:05 ` Petr Cvek
2015-09-28 21:39 ` [PATCH v4 20/26] ARM: pxa: magician: Add support for MAX1587A Vcore regulator Petr Cvek
2015-10-03 12:57 ` Philipp Zabel
2015-10-13 20:16 ` Robert Jarzmik
2015-09-28 21:39 ` [PATCH v4 21/26] ARM: pxa: magician: Add support for PXA27x UDC Petr Cvek
2015-10-03 12:58 ` Philipp Zabel
2015-10-13 20:29 ` Robert Jarzmik
2015-09-28 21:39 ` [PATCH v4 22/26] ARM: pxa: magician: Remove pdata for pasic3-leds Petr Cvek
2015-10-03 12:59 ` Philipp Zabel
2015-10-13 20:32 ` Robert Jarzmik
2015-09-28 21:40 ` [PATCH v4 23/26] ARM: pxa: magician: Remove definition of the STUART port Petr Cvek
2015-09-28 21:40 ` [PATCH v4 24/26] ARM: pxa: magician: Add debug message for backlight brightness function Petr Cvek
2015-09-28 21:40 ` [PATCH v4 25/26] ARM: pxa: magician: Add missing regulator for PWM backlight Petr Cvek
2015-10-03 13:02 ` Philipp Zabel
2015-09-28 21:42 ` [PATCH v4 26/26] ARM: pxa: magician: Move platform_add_devices() to the end of magician_init() Petr Cvek
2015-10-03 13:04 ` Philipp Zabel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5609B347.80202@tul.cz \
--to=petr.cvek@tul$(echo .)cz \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox