Subject: [PATCH v4 3/5] PCI: qcom: Add Qualcomm PCIe controller driver

From: [email-masked] (Stanimir Varbanov)
Date: Thu, 17 Dec 2015 15:18:43 +0200

Bjorn, thanks for the comments!

On 12/16/2015 11:53 PM, Bjorn Helgaas wrote:
> On Thu, Dec 03, 2015 at 03:35:22PM +0200, Stanimir Varbanov wrote:
>> From: Stanimir Varbanov <[email-masked]>
>>
>> The PCIe driver reuse the Designware common code for host
>> and MSI initialization, and also program the Qualcomm
>> application specific registers.
>>
>> Signed-off-by: Stanimir Varbanov <[email-masked]>
>> Signed-off-by: Stanimir Varbanov <[email-masked]>
>> ---
>>  MAINTAINERS                  |    7 +
>>  drivers/pci/host/Kconfig     |   10 +
>>  drivers/pci/host/Makefile    |    1 +
>>  drivers/pci/host/pcie-qcom.c |  624 ++++++++++++++++++++++++++++++++++++++++++
> 
>> +#define PCIE20_CAP				0x70
>> +#define PCIE20_CAP_LINKCTRLSTATUS		(PCIE20_CAP + 0x10)
>> +#define PCIE20_CAP_LINKCTRLSTATUS_LINK_UP	BIT(29)
> 
> This looks like it could be referring to a standard PCIe Capability;
> could you use the existing PCI_EXP_LNKSTA and PCI_EXP_LNKSTA_DLLLA
> symbols here?  And readw() instead of readl()?

Yes, that is possible but I still need to keep PCIE20_CAP capabilities
offset.

> 
>> +static int qcom_pcie_enable_link_training(struct qcom_pcie *pcie)
>> +{
>> +	struct device *dev = pcie->dev;
>> +	u32 val;
>> +	int ret;
>> +
>> +	/* enable link training */
>> +	val = readl(pcie->elbi + PCIE20_ELBI_SYS_CTRL);
>> +	val |= PCIE20_ELBI_SYS_CTRL_LT_ENABLE;
>> +	writel(val, pcie->elbi + PCIE20_ELBI_SYS_CTRL);
>> +
>> +	/* wait for up to 100ms for the link to come up */
>> +	ret = readl_poll_timeout(pcie->elbi + PCIE20_ELBI_SYS_STTS, val,
>> +				 val & XMLH_LINK_UP, LINKUP_DELAY_US,
>> +				 LINKUP_TIMEOUT_US);
>> +
>> +	if (ret < 0 || !dw_pcie_link_up(&pcie->pp)) {
>> +		dev_err(dev, "link initialization failed\n");
>> +		return -ETIMEDOUT;
>> +	}
>> +
>> +	return 0;
>> +}
> 
> This looks a lot like the *_establish_link() functions in other
> DesignWare-based drivers.  Can you make it look even more similar,
> e.g., by renaming it to qcom_pcie_establish_link() and maybe moving
> some of the PHY functionality here?
> 
> readl_poll_timeout() is nice and avoids the hand-coded timeout loop
> the other drivers use.  But is there benefit in checking for
> XMLH_LINK_UP, or could you simply poll dw_pcie_link_up() like the
> others do?  If it's sufficient, I'd prefer using dw_pcie_link_up()
> by itself because it's a little more generic.

OK I will modify the code to use dw_pcie_link_up() and ensure that this
check is sufficient.

-- 
regards,
Stan