Subject: [PATCH 3/3] thermal: exynos: Print a message about exceeded number of supported trip-points

From: [email-masked] (Chanwoo Choi)
Date: Thu, 18 Feb 2016 14:31:59 +0900

On 2016? 02? 18? 14:14, Krzysztof Kozlowski wrote:
> When DeviveTree contains more trip-points than SoC can configure
> (usually more than four) and polling mode is not enabled, then the
> remaining trip-points will be silently ignored. No interrupts will be
> generated for them.
> 
> This might be quite dangerous when one provides DTB with a
> non-configurable critical trip-point, like (assuming four supported
> thresholds in TMU):
>  - alert @50 C (type: active),
>  - alert @60 C (type: active),
>  - alert @70 C (type: active),
>  - alert @80 C (type: active),
>  - critical @120 C (type: critical) <- no interrupts generated.
> 
> This is a mistake in DTB so print a message in such case.
> 
> Signed-off-by: Krzysztof Kozlowski <[email-masked]>
> ---
>  drivers/thermal/samsung/exynos_tmu.c | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
> 
> diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
> index fa61eff88496..6c6f59ba7423 100644
> --- a/drivers/thermal/samsung/exynos_tmu.c
> +++ b/drivers/thermal/samsung/exynos_tmu.c
> @@ -184,6 +184,7 @@
>   * @temp_error2: fused value of the second point trim.
>   * @regulator: pointer to the TMU regulator structure.
>   * @reg_conf: pointer to structure to register with core thermal.
> + * @ntrip: number of supported trip points.
>   * @tmu_initialize: SoC specific TMU initialization method
>   * @tmu_control: SoC specific TMU control method
>   * @tmu_read: SoC specific TMU temperature read method
> @@ -203,6 +204,7 @@ struct exynos_tmu_data {
>  	u16 temp_error1, temp_error2;
>  	struct regulator *regulator;
>  	struct thermal_zone_device *tzd;
> +	unsigned int ntrip;
>  
>  	int (*tmu_initialize)(struct platform_device *pdev);
>  	void (*tmu_control)(struct platform_device *pdev, bool on);
> @@ -346,6 +348,14 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
>  	struct exynos_tmu_data *data = platform_get_drvdata(pdev);
>  	int ret;
>  
> +	if (of_thermal_get_ntrips(data->tzd) > data->ntrip) {
> +		dev_info(&pdev->dev,
> +			 "More trip points than supported by this TMU.\n");
> +		dev_info(&pdev->dev,
> +			 "%d trip points should be configured in polling mode.\n",
> +			 (of_thermal_get_ntrips(data->tzd) - data->ntrip));
> +	}
> +
>  	mutex_lock(&data->lock);
>  	clk_enable(data->clk);
>  	if (!IS_ERR(data->clk_sec))
> @@ -1210,6 +1220,7 @@ static int exynos_map_dt_data(struct platform_device *pdev)
>  		data->tmu_control = exynos4210_tmu_control;
>  		data->tmu_read = exynos4210_tmu_read;
>  		data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
> +		data->ntrip = 4;
>  		break;
>  	case SOC_ARCH_EXYNOS3250:
>  	case SOC_ARCH_EXYNOS4412:
> @@ -1222,6 +1233,7 @@ static int exynos_map_dt_data(struct platform_device *pdev)
>  		data->tmu_read = exynos4412_tmu_read;
>  		data->tmu_set_emulation = exynos4412_tmu_set_emulation;
>  		data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
> +		data->ntrip = 4;
>  		break;
>  	case SOC_ARCH_EXYNOS5433:
>  		data->tmu_initialize = exynos5433_tmu_initialize;
> @@ -1229,6 +1241,7 @@ static int exynos_map_dt_data(struct platform_device *pdev)
>  		data->tmu_read = exynos4412_tmu_read;
>  		data->tmu_set_emulation = exynos4412_tmu_set_emulation;
>  		data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
> +		data->ntrip = 8;
>  		break;
>  	case SOC_ARCH_EXYNOS5440:
>  		data->tmu_initialize = exynos5440_tmu_initialize;
> @@ -1236,6 +1249,7 @@ static int exynos_map_dt_data(struct platform_device *pdev)
>  		data->tmu_read = exynos5440_tmu_read;
>  		data->tmu_set_emulation = exynos5440_tmu_set_emulation;
>  		data->tmu_clear_irqs = exynos5440_tmu_clear_irqs;
> +		data->ntrip = 4;
>  		break;
>  	case SOC_ARCH_EXYNOS7:
>  		data->tmu_initialize = exynos7_tmu_initialize;
> @@ -1243,6 +1257,7 @@ static int exynos_map_dt_data(struct platform_device *pdev)
>  		data->tmu_read = exynos7_tmu_read;
>  		data->tmu_set_emulation = exynos4412_tmu_set_emulation;
>  		data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
> +		data->ntrip = 8;
>  		break;
>  	default:
>  		dev_err(&pdev->dev, "Platform not supported\n");
> 

Exynos5433 and Exynos7 have the 8 interrupt.

Reviewed-by: Chanwoo Choi <[email-masked]>

Best Regards,
Chanwoo Choi