Subject: [PATCH v4 1/2] clk: exynos5433: do not use CLK_IGNORE_UNUSED for SPI clocks

From: [email-masked] (Krzysztof Kozlowski)
Date: Thu, 07 Jul 2016 14:46:20 +0200

On 07/07/2016 02:13 PM, Andi Shyti wrote:
> The CLK_IGNORE_UNUSED flag has to be avoided whenever possible.
> Use the CLK_IS_CRITICAL flag instead for critical SPI1 clocks,
> which enables the clock line during boot time.

I don't agree. Both flags should be avoided. Clk is critical does not
solve the problem. It is just a better workaround for lack of proper
clock consumers.

The IOCLK is not a critical clock. It can be disabled (e.g. when SoC is
used on a board without any SPI device connected).

Best regards,
Krzysztof

> 
> Suggested-by: Tomasz Figa <[email-masked]>
> Signed-off-by: Andi Shyti <[email-masked]>
> ---
>  drivers/clk/samsung/clk-exynos5433.c | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/clk/samsung/clk-exynos5433.c b/drivers/clk/samsung/clk-exynos5433.c
> index c3a5318..337387b 100644
> --- a/drivers/clk/samsung/clk-exynos5433.c
> +++ b/drivers/clk/samsung/clk-exynos5433.c
> @@ -1662,7 +1662,7 @@ static struct samsung_gate_clock peric_gate_clks[] __initdata = {
>  			ENABLE_SCLK_PERIC, 13, CLK_SET_RATE_PARENT, 0),
>  	GATE(CLK_SCLK_IOCLK_SPI1, "sclk_ioclk_spi1", "ioclk_spi1_clk_in",
>  			ENABLE_SCLK_PERIC, 12,
> -			CLK_IGNORE_UNUSED | CLK_SET_RATE_PARENT, 0),
> +			CLK_IS_CRITICAL | CLK_SET_RATE_PARENT, 0),
>  	GATE(CLK_SCLK_IOCLK_SPI0, "sclk_ioclk_spi0", "ioclk_spi0_clk_in",
>  			ENABLE_SCLK_PERIC, 11, CLK_SET_RATE_PARENT, 0),
>  	GATE(CLK_SCLK_IOCLK_I2S1_BCLK, "sclk_ioclk_i2s1_bclk",
> @@ -1677,7 +1677,7 @@ static struct samsung_gate_clock peric_gate_clks[] __initdata = {
>  	GATE(CLK_SCLK_SPI2, "sclk_spi2", "sclk_spi2_peric", ENABLE_SCLK_PERIC,
>  			5, CLK_SET_RATE_PARENT, 0),
>  	GATE(CLK_SCLK_SPI1, "sclk_spi1", "sclk_spi1_peric", ENABLE_SCLK_PERIC,
> -			4, CLK_IGNORE_UNUSED | CLK_SET_RATE_PARENT, 0),
> +			4, CLK_SET_RATE_PARENT, 0),
>  	GATE(CLK_SCLK_SPI0, "sclk_spi0", "sclk_spi0_peric", ENABLE_SCLK_PERIC,
>  			3, CLK_SET_RATE_PARENT, 0),
>  	GATE(CLK_SCLK_UART2, "sclk_uart2", "sclk_uart2_peric",
>