Subject: Re: [PATCH 1/2] arm64: dts: hisilicon: Use phandles for overriding nodes in hi6220

From: Wei Xu <[email-masked]>
Date: Tue, 21 Jul 2020 10:43:17 +0800

Hi Krzysztof

On 2020/6/29 16:16, Krzysztof Kozlowski wrote:
> When overriding nodes, usage of phandles instead of full paths reduces
> possible mistakes (e.g.  in duplicated unit address) and removes
> duplicate data.  The UART nodes were extended via full path and phandle
> which makes it difficult to review and spot actual differences.
> 
> No functional change (no difference in dtx_diff).
> 
> Signed-off-by: Krzysztof Kozlowski <[email-masked]>

Thanks!
Series applied to the hisilicon arm64 dt tree.

Best Regards,
Wei

> ---
>  .../arm64/boot/dts/hisilicon/hi6220-hikey.dts | 426 +++++++++---------
>  1 file changed, 210 insertions(+), 216 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> index c14205cd6bf5..a41e0db8e71b 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> @@ -122,222 +122,6 @@
>  		power-off-delay-us = <10>;
>  	};
>  
> -	soc {
> -		spi0: spi@f7106000 {
> -			status = "ok";
> -		};
> -
> -		i2c0: i2c@f7100000 {
> -			status = "ok";
> -		};
> -
> -		i2c1: i2c@f7101000 {
> -			status = "ok";
> -		};
> -
> -		uart1: uart@f7111000 {
> -			assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>;
> -			assigned-clock-rates = <150000000>;
> -			status = "ok";
> -
> -			bluetooth {
> -				compatible = "ti,wl1835-st";
> -				enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> -				clocks = <&pmic>;
> -				clock-names = "ext_clock";
> -			};
> -		};
> -
> -		uart2: uart@f7112000 {
> -			status = "ok";
> -		};
> -
> -		uart3: uart@f7113000 {
> -			status = "ok";
> -		};
> -
> -		/*
> -		 * Legend: proper name = the GPIO line is used as GPIO
> -		 *         NC = not connected (not routed from the SoC)
> -		 *         "[PER]" = pin is muxed for peripheral (not GPIO)
> -		 *         "" = no idea, schematic doesn't say, could be
> -		 *              unrouted (not connected to any external pin)
> -		 *         LSEC = Low Speed External Connector
> -		 *         HSEC = High Speed External Connector
> -		 *
> -		 * Pin assignments taken from LeMaker and CircuitCo Schematics
> -		 * Rev A1.
> -		 *
> -		 * For the lines routed to the external connectors the
> -		 * lines are named after the 96Boards CE Specification 1.0,
> -		 * Appendix "Expansion Connector Signal Description".
> -		 *
> -		 * When the 96Board naming of a line and the schematic name of
> -		 * the same line are in conflict, the 96Board specification
> -		 * takes precedence, which means that the external UART on the
> -		 * LSEC is named UART0 while the schematic and SoC names this
> -		 * UART2. This is only for the informational lines i.e. "[FOO]",
> -		 * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
> -		 * ones actually used for GPIO.
> -		 */
> -		gpio0: gpio@f8011000 {
> -			gpio-line-names = "PWR_HOLD", "DSI_SEL",
> -			"USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON",
> -			"PWRON_DET", "5V_HUB_EN";
> -		};
> -
> -		gpio1: gpio@f8012000 {
> -			gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N",
> -			"WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON";
> -		};
> -
> -		gpio2: gpio@f8013000 {
> -			gpio-line-names =
> -				"GPIO-A", /* LSEC Pin 23: GPIO2_0 */
> -				"GPIO-B", /* LSEC Pin 24: GPIO2_1 */
> -				"GPIO-C", /* LSEC Pin 25: GPIO2_2 */
> -				"GPIO-D", /* LSEC Pin 26: GPIO2_3 */
> -				"GPIO-E", /* LSEC Pin 27: GPIO2_4 */
> -				"USB_ID_DET", "USB_VBUS_DET",
> -				"GPIO-H"; /* LSEC Pin 30: GPIO2_7 */
> -		};
> -
> -		gpio3: gpio@f8014000 {
> -			gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "",
> -			"WLAN_ACTIVE", "NC", "NC";
> -		};
> -
> -		gpio4: gpio@f7020000 {
> -			gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3",
> -			"USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE";
> -		};
> -
> -		gpio5: gpio@f7021000 {
> -			gpio-line-names = "NC", "NC",
> -			"[UART1_RxD]", /* LSEC Pin 11: UART3_RX */
> -			"[UART1_TxD]", /* LSEC Pin 13: UART3_TX */
> -			"[AUX_SSI1]", "NC",
> -			"[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */
> -			"[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */
> -		};
> -
> -		gpio6: gpio@f7022000 {
> -			gpio-line-names =
> -			"[SPI0_DIN]", /* Pin 10: SPI0_DI */
> -			"[SPI0_DOUT]", /* Pin 14: SPI0_DO */
> -			"[SPI0_CS]", /* Pin 12: SPI0_CS_N */
> -			"[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */
> -			"NC", "NC", "NC",
> -			"GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */
> -		};
> -
> -		gpio7: gpio@f7023000 {
> -			gpio-line-names = "NC", "NC", "NC", "NC",
> -			"[PCM_DI]", /* Pin 22: MODEM_PCM_DI */
> -			"[PCM_DO]", /* Pin 20: MODEM_PCM_DO */
> -			"NC", "NC";
> -		};
> -
> -		gpio8: gpio@f7024000 {
> -			gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC",
> -			"", "", "", "", "", "";
> -		};
> -
> -		gpio9: gpio@f7025000 {
> -			gpio-line-names = "",
> -			"GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */
> -			"GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */
> -			"NC", "NC", "NC", "NC", "[ISP_CCLK0]";
> -		};
> -
> -		gpio10: gpio@f7026000 {
> -			gpio-line-names = "BOOT_SEL",
> -			"[ISP_CCLK1]",
> -			"GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */
> -			"GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */
> -			"NC", "NC",
> -			"[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */
> -			"[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */
> -		};
> -
> -		gpio11: gpio@f7027000 {
> -			gpio-line-names =
> -			"[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */
> -			"[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */
> -			"", "NC", "NC", "NC", "", "";
> -		};
> -
> -		gpio12: gpio@f7028000 {
> -			gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]",
> -			"[BT_PCM_DO]",
> -			"NC", "NC", "NC", "NC",
> -			"GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */
> -		};
> -
> -		gpio13: gpio@f7029000 {
> -			gpio-line-names = "[UART0_RX]", "[UART0_TX]",
> -			"[BT_UART1_CTS]", "[BT_UART1_RTS]",
> -			"[BT_UART1_RX]", "[BT_UART1_TX]",
> -			"[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */
> -			"[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */
> -		};
> -
> -		gpio14: gpio@f702a000 {
> -			gpio-line-names =
> -			"[UART0_RxD]", /* LSEC Pin 7: UART2_RX */
> -			"[UART0_TxD]", /* LSEC Pin 5: UART2_TX */
> -			"[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */
> -			"[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */
> -			"[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */
> -			"[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */
> -			"[I2C2_SCL]", "[I2C2_SDA]";
> -		};
> -
> -		gpio15: gpio@f702b000 {
> -			gpio-line-names = "", "", "", "", "", "", "NC", "";
> -		};
> -
> -		/* GPIO blocks 16 thru 19 do not appear to be routed to pins */
> -
> -		dwmmc_0: dwmmc0@f723d000 {
> -			cap-mmc-highspeed;
> -			non-removable;
> -			bus-width = <0x8>;
> -			vmmc-supply = <&ldo19>;
> -		};
> -
> -		dwmmc_1: dwmmc1@f723e000 {
> -			card-detect-delay = <200>;
> -			cap-sd-highspeed;
> -			sd-uhs-sdr12;
> -			sd-uhs-sdr25;
> -			sd-uhs-sdr50;
> -			vqmmc-supply = <&ldo7>;
> -			vmmc-supply = <&ldo10>;
> -			bus-width = <0x4>;
> -			disable-wp;
> -			cd-gpios = <&gpio1 0 1>;
> -		};
> -
> -		dwmmc_2: dwmmc2@f723f000 {
> -			bus-width = <0x4>;
> -			non-removable;
> -			cap-power-off-card;
> -			vmmc-supply = <&reg_vdd_3v3>;
> -			mmc-pwrseq = <&wl1835_pwrseq>;
> -
> -			#address-cells = <0x1>;
> -			#size-cells = <0x0>;
> -			wlcore: wlcore@2 {
> -				compatible = "ti,wl1835";
> -				reg = <2>;	/* sdio func num */
> -				/* WL_IRQ, WL_HOST_WAKE_GPIO1_3 */
> -				interrupt-parent = <&gpio1>;
> -				interrupts = <3 IRQ_TYPE_EDGE_RISING>;
> -			};
> -		};
> -	};
> -
>  	leds {
>  		compatible = "gpio-leds";
>  
> @@ -480,10 +264,26 @@
>  	};
>  };
>  
> +&uart1 {
> +	assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>;
> +	assigned-clock-rates = <150000000>;
> +	status = "ok";
> +
> +	bluetooth {
> +		compatible = "ti,wl1835-st";
> +		enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> +		clocks = <&pmic>;
> +		clock-names = "ext_clock";
> +	};
> +};
> +
>  &uart2 {
> +	status = "ok";
>  	label = "LS-UART0";
>  };
> +
>  &uart3 {
> +	status = "ok";
>  	label = "LS-UART1";
>  };
>  
> @@ -506,6 +306,196 @@
>  	};
>  };
>  
> +&dwmmc_0 {
> +	cap-mmc-highspeed;
> +	non-removable;
> +	bus-width = <0x8>;
> +	vmmc-supply = <&ldo19>;
> +};
> +
> +&dwmmc_1 {
> +	card-detect-delay = <200>;
> +	cap-sd-highspeed;
> +	sd-uhs-sdr12;
> +	sd-uhs-sdr25;
> +	sd-uhs-sdr50;
> +	vqmmc-supply = <&ldo7>;
> +	vmmc-supply = <&ldo10>;
> +	bus-width = <0x4>;
> +	disable-wp;
> +	cd-gpios = <&gpio1 0 1>;
> +};
> +
> +&dwmmc_2 {
> +	bus-width = <0x4>;
> +	non-removable;
> +	cap-power-off-card;
> +	vmmc-supply = <&reg_vdd_3v3>;
> +	mmc-pwrseq = <&wl1835_pwrseq>;
> +
> +	#address-cells = <0x1>;
> +	#size-cells = <0x0>;
> +	wlcore: wlcore@2 {
> +		compatible = "ti,wl1835";
> +		reg = <2>;	/* sdio func num */
> +		/* WL_IRQ, WL_HOST_WAKE_GPIO1_3 */
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
> +	};
> +};
> +
> +/*
> + * Legend: proper name = the GPIO line is used as GPIO
> + *         NC = not connected (not routed from the SoC)
> + *         "[PER]" = pin is muxed for peripheral (not GPIO)
> + *         "" = no idea, schematic doesn't say, could be
> + *              unrouted (not connected to any external pin)
> + *         LSEC = Low Speed External Connector
> + *         HSEC = High Speed External Connector
> + *
> + * Pin assignments taken from LeMaker and CircuitCo Schematics
> + * Rev A1.
> + *
> + * For the lines routed to the external connectors the
> + * lines are named after the 96Boards CE Specification 1.0,
> + * Appendix "Expansion Connector Signal Description".
> + *
> + * When the 96Board naming of a line and the schematic name of
> + * the same line are in conflict, the 96Board specification
> + * takes precedence, which means that the external UART on the
> + * LSEC is named UART0 while the schematic and SoC names this
> + * UART2. This is only for the informational lines i.e. "[FOO]",
> + * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
> + * ones actually used for GPIO.
> + */
> +&gpio0 {
> +	gpio-line-names = "PWR_HOLD", "DSI_SEL",
> +	"USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON",
> +	"PWRON_DET", "5V_HUB_EN";
> +};
> +
> +&gpio1 {
> +	gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N",
> +	"WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON";
> +};
> +
> +&gpio2 {
> +	gpio-line-names =
> +		"GPIO-A", /* LSEC Pin 23: GPIO2_0 */
> +		"GPIO-B", /* LSEC Pin 24: GPIO2_1 */
> +		"GPIO-C", /* LSEC Pin 25: GPIO2_2 */
> +		"GPIO-D", /* LSEC Pin 26: GPIO2_3 */
> +		"GPIO-E", /* LSEC Pin 27: GPIO2_4 */
> +		"USB_ID_DET", "USB_VBUS_DET",
> +		"GPIO-H"; /* LSEC Pin 30: GPIO2_7 */
> +};
> +
> +&gpio3 {
> +	gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "",
> +	"WLAN_ACTIVE", "NC", "NC";
> +};
> +
> +&gpio4 {
> +	gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3",
> +	"USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE";
> +};
> +
> +&gpio5 {
> +	gpio-line-names = "NC", "NC",
> +	"[UART1_RxD]", /* LSEC Pin 11: UART3_RX */
> +	"[UART1_TxD]", /* LSEC Pin 13: UART3_TX */
> +	"[AUX_SSI1]", "NC",
> +	"[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */
> +	"[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */
> +};
> +
> +&gpio6 {
> +	gpio-line-names =
> +	"[SPI0_DIN]", /* Pin 10: SPI0_DI */
> +	"[SPI0_DOUT]", /* Pin 14: SPI0_DO */
> +	"[SPI0_CS]", /* Pin 12: SPI0_CS_N */
> +	"[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */
> +	"NC", "NC", "NC",
> +	"GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */
> +};
> +
> +&gpio7 {
> +	gpio-line-names = "NC", "NC", "NC", "NC",
> +	"[PCM_DI]", /* Pin 22: MODEM_PCM_DI */
> +	"[PCM_DO]", /* Pin 20: MODEM_PCM_DO */
> +	"NC", "NC";
> +};
> +
> +&gpio8 {
> +	gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC",
> +	"", "", "", "", "", "";
> +};
> +
> +&gpio9 {
> +	gpio-line-names = "",
> +	"GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */
> +	"GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */
> +	"NC", "NC", "NC", "NC", "[ISP_CCLK0]";
> +};
> +
> +&gpio10 {
> +	gpio-line-names = "BOOT_SEL",
> +	"[ISP_CCLK1]",
> +	"GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */
> +	"GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */
> +	"NC", "NC",
> +	"[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */
> +	"[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */
> +};
> +
> +&gpio11 {
> +	gpio-line-names =
> +	"[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */
> +	"[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */
> +	"", "NC", "NC", "NC", "", "";
> +};
> +
> +&gpio12 {
> +	gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]",
> +	"[BT_PCM_DO]",
> +	"NC", "NC", "NC", "NC",
> +	"GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */
> +};
> +
> +&gpio13 {
> +	gpio-line-names = "[UART0_RX]", "[UART0_TX]",
> +	"[BT_UART1_CTS]", "[BT_UART1_RTS]",
> +	"[BT_UART1_RX]", "[BT_UART1_TX]",
> +	"[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */
> +	"[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */
> +};
> +
> +&gpio14 {
> +	gpio-line-names =
> +	"[UART0_RxD]", /* LSEC Pin 7: UART2_RX */
> +	"[UART0_TxD]", /* LSEC Pin 5: UART2_TX */
> +	"[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */
> +	"[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */
> +	"[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */
> +	"[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */
> +	"[I2C2_SCL]", "[I2C2_SDA]";
> +};
> +
> +&gpio15 {
> +	gpio-line-names = "", "", "", "", "", "", "NC", "";
> +};
> +
> +/* GPIO blocks 16 thru 19 do not appear to be routed to pins */
> +
> +
> +&i2c0 {
> +	status = "ok";
> +};
> +
> +&i2c1 {
> +	status = "ok";
> +};
> +
>  &i2c2 {
>  	#address-cells = <1>;
>  	#size-cells = <0>;
> @@ -549,3 +539,7 @@
>  		};
>  	};
>  };
> +
> +&spi0 {
> +	status = "ok";
> +};
> 

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel