Subject: Re: [PATCH] dt-bindings: memory-controllers: Convert Samsung Exynos SROM bindings to json-schema

From: Rob Herring <[email-masked]>
Date: Fri, 13 Sep 2019 15:36:14 +0100

On Sat, Sep 07, 2019 at 04:44:42PM +0200, Krzysztof Kozlowski wrote:
> Convert Samsung Exynos SROM controller bindings to DT schema format
> using json-schema.
> 
> Signed-off-by: Krzysztof Kozlowski <[email-masked]>
> ---
>  .../memory-controllers/exynos-srom.txt        |  79 ----------
>  .../memory-controllers/exynos-srom.yaml       | 136 ++++++++++++++++++
>  2 files changed, 136 insertions(+), 79 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt
>  create mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml

> diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml
> new file mode 100644
> index 000000000000..9573bcfd68bf
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml
> @@ -0,0 +1,136 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/memory-controllers/exynos-srom.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Samsung Exynos SoC SROM Controller driver
> +
> +maintainers:
> +  - Krzysztof Kozlowski <[email-masked]>
> +
> +description: |+
> +  The SROM controller can be used to attach external peripherals. In this case
> +  extra properties, describing the bus behind it, should be specified.
> +
> +properties:
> +  compatible:
> +    items:
> +      - const: samsung,exynos4210-srom
> +
> +  reg:
> +    maxItems: 1
> +
> +  "#address-cells":
> +    const: 2
> +
> +  "#size-cells":
> +    const: 1
> +
> +  ranges:
> +    description: |
> +      Reflects the memory layout with four integer values per bank. Format:
> +      <bank-number> 0 <parent address of bank> <size>
> +
> +patternProperties:
> +  "^.*@[0-9]+,[0-9]+$":

How many chip selects? Can be a single digit?

Also, these should be hex values.

> +    type: object
> +    description:
> +      The actual device nodes should be added as subnodes to the SROMc node.
> +      These subnodes, in addition to regular device specification, should
> +      contain the following properties, describing configuration
> +      of the relevant SROM bank.
> +
> +    properties:
> +      reg:
> +        description:
> +          Bank number, base address (relative to start of the bank) and size
> +          of the memory mapped for the device. Note that base address will be
> +          typically 0 as this is the start of the bank.
> +        maxItems: 1
> +
> +      reg-io-width:
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32
> +          - enum: [1, 2]
> +        description:
> +          Data width in bytes (1 or 2). If omitted, default of 1 is used.
> +
> +      samsung,srom-page-mode:
> +        description:
> +          If page mode is set, 4 data page mode will be configured,
> +          else normal (1 data) page mode will be set.
> +        type: boolean
> +
> +      samsung,srom-timing:
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32-array
> +          - items:
> +              minItems: 6
> +              maxItems: 6
> +        description: |
> +          Array of 6 integers, specifying bank timings in the following order:
> +          Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs.
> +          Each value is specified in cycles and has the following meaning
> +          and valid range:
> +          Tacp: Page mode access cycle at Page mode (0 - 15)
> +          Tcah: Address holding time after CSn (0 - 15)
> +          Tcoh: Chip selection hold on OEn (0 - 15)
> +          Tacc: Access cycle (0 - 31, the actual time is N + 1)
> +          Tcos: Chip selection set-up before OEn (0 - 15)
> +          Tacs: Address set-up before CSn (0 - 15)
> +
> +    required:
> +      - reg
> +      - samsung,srom-timing
> +
> +required:
> +  - compatible
> +  - reg
> +
> +allOf:
> +  - if:
> +      anyOf:
> +        - required: [ "#address-cells" ]
> +        - required: [ ranges ]
> +        - required: [ "#size-cells" ]
> +    then:
> +      required:
> +        - "#address-cells"
> +        - ranges
> +        - "#size-cells"

I don't think this is necessary as the core schema should take care of 
it. This can also be expressed using 'dependencies'. 

Rob

_______________________________________________
linux-arm-kernel mailing list
[email-masked]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel